Metallic glasses can be considered for many commercial applications because of the higher mechanical strength, corrosion and wear resistance when compared to crystalline materials. To consider them for novel applications, the challenge of preparing metallic glasses from the liquid melt phase and how the properties of metallic glasses change due to relaxation need to be understood better. The glass forming ability (GFA) with variation in composition and inclusion of different alloying elements was studied by using thermal techniques to determine important GFA indicators for Zr-based bulk metallic glasses (BMG). The effect of alloying elements, annealing temperature and annealing time on the thermal and structural relaxation of the BMGs was studied by using an annealing induced relaxation approach. The thermal relaxation was studied by measuring specific heat of the samples using differential scanning calorimeter (DSC) and calculating the enthalpy recovery on reheating in the BMG samples. The structural relaxation was also studied by using extended X-ray absorption fine structure (EXAFS) technique on the as-obtained and relaxed samples. The effects of alloying elements and annealing on electrical resistance were studied by using a two point probe. From the study, it was found that the currently used GFA indicators are inadequate to fully capture and identify the best GFA BMGs. The fragility (beta) of the melt is a new criterion that has been proposed to measure and analyze GFA. The enthalpy relaxation of Zrbased BMGs was found to follow a stretched exponential function, and the parameters obtained showed the BMGs used in the current study are strong glass formers. EXAFS studies showed variations in the structure of BMGs with changes in alloying elements. Furthermore, alloying elements were found to have an effect on the structure of the relaxed BMGs. The resistance of BMGs was found to decrease with relaxation which can be attributed to short range order on annealing.

The thermal and mechanical properties of the Mg-based bulk metallic glasses are reported in this thesis. The original ingots were prepared by arc melting and induction melting. The thermal and mechanical properties of the Mg-based bulk metallic glasses are reported in this thesis. The original ingots were prepared by arc melting and induction melting. The Mg65Cu25Gd10 and Mg65Cu15Ag10Gd10 bulk metallic glasses with different diameters from 3 to 6 mm were successfully fabricated by conventional copper mold casting in an inert atmosphere. The Mg65Cu25Gd10 bulk metallic glass shows the high glass forming ability and good thermal stability. However, the addition of Ag in the Mg65Cu15Ag10Gd10 alloy degrades the thermal stability. Based on the DSC results, the supercooled liquid region

It is of great importance for a materials scientist both from fundamental and applicability aspects to have better understanding of solid-state phase transformations and its kinetics responsible for micro-/nano-structure development in alloys and corresponding physical and mechanical properties. Transformation kinetics can be analyzed by various experimental techniques such as thermal analysis, laborious electron microscopy combined with extensive image analysis or by measuring changes in electrical resistivity, specimen volume and relative intensities of diffraction lines caused by the phase transformation. Beyond these conventional techniques, this dissertation provides a novel magnetic monitoring approach to study the isothermal kinetics of phase transformations in multicomponent alloy systems involving measurable changes in overall magnetic moment as the transformation proceeds. This dissertation focuses on understanding the microstructural evolution, macro- and micro-alloying behavior, magnetic properties, thermal characteristics, mechanical properties and kinetics of solid-state transformations, i.e. nanoscale precipitation and nanocrystallization, in nickel aluminides and Fe-based bulk amorphous alloys. Microstructural characterization of alloys was done by X-ray diffraction, scanning electron microscopy and transmission electron microcopy techniques. Magnetic properties were analyzed by vibrating sample magnetometry whereas thermal characteristics were evaluated by differential scanning calorimetry. Mechanical properties of alloys were determined by microhardness measurements and compression tests. The influence of Fe macroalloying and 3d transition metal microalloying on the microstructure and properties of Ni-Al-Fe alloys were studied for as-cast and annealed states and it is shown that desired microstructure and related properties can be obtained by proper selection of the type and concentration of macro- or micro-alloying elements together with an appropriate annealing procedure. Thermomagnetic characterization reveals the nanoscale precipitation of a ferromagnetic second phase with annealing. In conjunction with saturation magnetization dependence on annealing, an optimum temperature is identified where nanoscale precipitates impart the highest extent of precipitation strengthening. The isothermal kinetics of ferromagnetic second phase precipitation reveals invariant Avrami exponents close to unity, indicating that nanoscale precipitation is governed by a diffusion-controlled growth process with decreasing growth rate, which closely resembles continuous precipitation kinetics. Appropriate annealing of the Fe-based bulk amorphous alloy precursor produced by suction casting demonstrated extremely fine microstructures containing uniformly distributed and densely dispersed nanocrystals inside a residual amorphous matrix. In order to have better understanding of nanocrystallization mechanisms, kinetic parameters were determined via isothermal magnetic monitoring and non-isothermal differential scanning calorimetry where excellent agreement was obtained in Avrami exponent and activation energy. Analyzing the local kinetics, the nanocrystalline phase was found to evolve through distinct transformation regimes during annealing which were discussed on the basis of transformation kinetics theory and microscopical investigations on each characteristic transformation regime.

Brightness enhancement film (BEF) has been manufactured in foreign factories for backlight module of liquid crystal display (LCD), then it only have some interior factories to put in exploitation. Because of this, the study presents a precision machining and new step-imprint hot embossing process to fabricate pyramid-shaped microlens array. First, a tungsten (W) steel material is manufactured by precision machining. The dimension of a pyramid-shaped microlens on the W steel are about 300 £gm in the base line of three side, 222 £gm in bevel edge of three side, 139 £gm in height of bottom to top, 180 £gm in pitch of the left and right sides between two pyramid-shaped microlens tips, and 85 degree in top angle of three bevel. The W steel mold is used as the first mold. Second, the pyramid peaks of first mold pattern are transferred on bulk metallic glass (BMG) using step-imprint hot embossing method with position adjustable mechanism to form a smaller concave pyramid-shaped microlens array, it can avoid arc radius of cutting tools which is used as the second mold. Another the pyramid peaks are transferred on PMMA (Polymethylmethacrylate) for concave pyramid-shaped microlens array of optical film in the hot embossing system. Finally, the second mold is fabricated to emboss convex pyramid-shaped microlens array of optical film on PMMA. The foregoing method is provided for backlight module of optical films process.

To achieve the miniaturization and high performance of the mobile phone, notebook, hearing aid and personal digital assistant (PDA), many researchers focus on the developing a new-type microphone with very small dimension, high quality and low manufacturing cost utilizing MEMS technology. By using the surface and bulk micromachining technologies, this thesis designed and fabricated a capacitive MEMS microphone with a polyimide bcakplate microstructure. The main processing steps adopted in this study include five photolithoghaphies and seven thin-film depositions. A MEMS-based microphone with an only 2¡Ñ2 mm2 sensing area of the floating Si3N4/Poly-Si/Si3N4 membrane and a 2 £gm-height gap distance between the top and bottom electrodes was implemented and characterized. Measured in a special isolated-box and under 1 kHz audio frequency, a -60.3 dB/Pa sensitivity (deducted the 22.6 dB output gain of the pre-amplifier) and a 51 dB signal to noise ratio (SNR) of the implemented MEMS microphone can be obtained as the biasing voltage only about 3 volts. The very low driving voltage, moderate SNR and sensitivity demonstrated in this work keep abreast with the results of many outstanding research laboratories in the world.

Utilizing the bulk and surface micromachining technologies, this thesis designed and fabricated a piezoresistive pressure microsensor for developing an in-vivo and real-time biomedical detection microsystem to monitor the uric pressure in patients¡¦ bladder. In this study, the main processing steps include the implantation of a moderate boron ion concentration into the N-epitaxial silicon layer to form the piezoresistors, anisotropic etching the backside silicon substrate to create a cavity by 30% KOH solution in 80¢XC temperature, and anodic bonding of the silicon based pressure microsensor and the hole-drilled glass sustain. To obtain the optimum design specification of the piezoresistive pressure microsensor, this study compared the characterization of the four types of devices with three different pressure sensing area (As) and two different length/width ratios (L/W) of the N-epitaxial piezoresistors. Based on the measurement results, the highest sensitivity (0.0076mV/(V*kgf/cm2) can be achieved as the As and the L/W ratio are equal to 1050 ¡Ñ 1050 £gm2 and 90/9 £gm/£gm, respectively. Such sensitivity is suitable for the application of bladder pressure detection microsystem. A very high sensing linearity (99.6%) can also be demonstrated in this research and this value approach to that of the commercial pressure sensor. On the other hand, through cooperation with another laboratory, this work has established a prototype of the uric pressure detecting microsystem by assembled with the piezoresistive pressure microsensor, a control ASIC and a radio-frequency (RF) module.

Mercuric Iodide in its tetragonal form has received a lot of attention for many years as a prospective room temperature X-ray and y-ray detector. Its basic properties are well suited for this purpose. Its wide band gap of 2.1eV contributes to a high dark resistivity of 1012ohm-cm or higher. A high atomic number of its constituent atoms (Hg-80, I -53) and a density of 6.3g/cm3 result in its efficient interaction with incident X-ray or y-ray radiation. Single crystalline mercuric iodide has been thoroughly studied and successfully utilized in commercial radiation detectors. But with the urgent need for large area ,low cost efficient X-ray detectors, focus has now shifted towards the development and understanding of the properties of thin film Polycrystalline Mercuric iodide detectors. Such detectors also have the advantage of being most suited for direct X-ray detection i.e. a direct conversion of incident X rays into electric signals which are then used to obtain an equivalent image in digital X-ray imaging. They also can be used in applications where a scintillator intermediate is used to generate visible light from incident high energy photons.Therefore it is important to study their optical response in order to understand and evaluate their Optical Properties. The present work focuses on obtaining the Optical response of the thin film Mercuric iodide photoconductive detectors .These films were grown on TEC-15 LOF glass with a Tin Oxide (SnO2) coating on it, which acts as a growth surface for the films and also functions as the front contact of the detector.Palladium which is sputtered on top of this film acts as the back contact. There are a total of seven contacted devices on each film sample and each device has been tested for its optical response in terms of Spectral Response and I-V characteristics in both light and dark conditions.

For more than 20 years, scientists have studied solar cells made from organic semiconductors. Throughout this time, device structures have evolved from bilayer devices to bulk heterojunction (BHJ) devices and even though efficiencies are approaching 10%, scientists still know relatively little about the transport of charge carriers and recombination mechanisms in these materials. Novel structures, based on lateral BHJ solar cells, have proven to be versatile tools to study transport and recombination mechanisms. In addition, these structures can easily be employed by researchers and solar cell manufacturers to determine the quality and measure the improvement of their materials. For these studies, poly(3-hexylthiophene) (P3HT):[6,6]-phenyl C61-butyric acid methyl ester (PCBM) has been employed due to its wide use among researchers as well as potential for commercialization. DC photocurrent measurements as a function of device length have yielded the mobility-lifetime product and the generation rate of free carriers within these BHJ devices. In addition to these parameters, the recombination rate as a function of light intensity provides information about the mechanisms of recombination. For example, by measuring the recombination rate as a function of applied electric field and light intensity we have found that recombination is unimolecular in nature and shifts to bimolecular at increased electric field strengths. Additionally, the mobility-lifetime product, generation rate, and recombination mechanism have been studied as a function of applied electric field, illumination spectrum, illumination intensity, etc. This information has provided much insight on physics of the P3HT:PCBM material system which did not exist before these studies. / text

The growth of bulk cubic silicon carbide has for a long time seemed to be something for the future. However, in this thesis the initial steps towards bulk cubic silicon carbide have been taken. The achievement of producing bulk cubic silicon carbide will have a great impact in various fields of science and industry such as for example the fields of semiconductor technology within electronic- and optoelectronic devices and bio-medical applications. The process that has been used to grow the bulk cubic silicon carbide is a modification of the seeded sublimation growth, and the seeds have been grown by sublimation epitaxy. Selected samples have been characterized with a variety of different methods. The surface morphology of the samples has been examined using optical microscope, atomic force microscope and scanning electron microscope. The crystal structure has been investigated by the methods X-ray diffraction and transmission electron microscopy. The electrical resistance of the grown seeds was evaluated by four probe measurements. High crystal quality seeds have been grown with semiconductor properties and bulk silicon carbide was demonstrated using the seeds.

Dominica has been recognized for its landscape containing hundreds of rivers and receiving high rainfall, and "our water belongs to the world," or so says many Dominican citizens, and their government. A schism exists in the understanding of the water resources of Dominica. Local perceptions are in conflict with regional climate change data. Where climate change research has found Dominica to be high risk for water quality and quantity, locals maintain the mindset that there is an overabundance of the resource. Local epistemologies influence governmental water management practices, which presently focus on exportation of the resource. In efforts of economic development, while trusting that there is a surplus of water, Dominica leases billions of gallons of water each year to foreign companies. A popular conception on the island is that there is an abundance of water, and therefore, it should be shared globally. This unique social construction of Dominican water has been a foundation leading to the sale of billions of gallons of fresh water to international corporations. However, the bulk exportation of water is occurring in the context of climate change, and thus, the availability of water will be impacted by changes in annual rainfall, sea level rise, increased temperatures, and more severe hurricanes. The purpose of this study is to gain a better understanding of how the social understanding of water in Dominica was constructed, and what this means in relation to resource exportation and climate change. This research-based paper explores Dominican perceptions of water abundance and sustainability.