Indiana University-Purdue University Indianapolis (IUPUI) / Recently, the concept of “bulk-fill” resin-based composites (RBCs) has been re-emphasized, with claimed improvements in depth of cure (DOC) with similar mechanical properties and comparable adaptation to walls and margins relative to conventional composite. More research is needed to carefully examine the properties of these new materials. The objective of this study was to measure the light energy, microhardness (VHN), and elastic modulus across the depth of one conventional and three bulk-fill RBCs. Materials and Methods: Three commercially available bulk-fill RBCs (Tetric EvoCeram Bulk Fill [TE], SonicFill [SF], X-tra fill[XF]) and one conventional RBC (Premise [PR]) were evaluated (n = 10). DOC (using Vickers’s microhardness), elastic modulus (using atomic force microscopy), and the mean irradiance and total light energy transmitted through different thicknesses of RBC were measured by a spectrometer. The effects of group, location, and curing depth on VHN were analyzed using mixed-model ANOVA. Elastic modulus and light energy comparisons were made using two-way ANOVA, with a significance level of 5 percent. Results: There was a significant difference in the depths for the mean irradiance and total energy between different depths in all materials. All materials achieved the manufacturers’ claimed DOC. XF had the highest DOC with 7 mm and a light energy of 0.56± 0.02 J/cm2 at 7 mm. PR had the lowest DOC with 3 mm and a light energy of 0.84 ±0.12 J/cm2 at 3 mm. The elastic modulus showed significant variation in depth profiles that were different than the DOC. Significance: The manufacturers’ claims for bulk-fill DOC were achieved using a microhardness method. However, this method failed to detect the quality of the polymerization. Assessment of the elastic modulus using AFM is a promising method for greater understanding of the polymerization.

京都大学 / 0048 / 新制・課程博士 / 博士(農学) / 甲第18313号 / 農博第2038号 / 新制||農||1020(附属図書館) / 学位論文||H26||N4820(農学部図書室) / 31171 / 京都大学大学院農学研究科食品生物科学専攻 / (主査)教授 安達 修二, 教授 河田 照雄, 教授 保川 清 / 学位規則第4条第1項該当 / Doctor of Agricultural Science / Kyoto University / DFAM

京都大学 / 0048 / 新制・課程博士 / 博士(エネルギー科学) / 甲第18381号 / エネ博第293号 / 新制||エネ||61(附属図書館) / 31239 / 京都大学大学院エネルギー科学研究科エネルギー基礎科学専攻 / (主査)教授 佐川 尚, 教授 八尾 健, 教授 萩原 理加 / 学位規則第4条第1項該当 / Doctor of Energy Science / Kyoto University / DGAM

京都大学 / 0048 / 新制・課程博士 / 博士(工学) / 甲第18469号 / 工博第3905号 / 新制||工||1599(附属図書館) / 31347 / 京都大学大学院工学研究科機械理工学専攻 / (主査)教授 西脇 眞二, 教授 椹木 哲夫, 教授 松原 厚 / 学位規則第4条第1項該当 / Doctor of Philosophy (Engineering) / Kyoto University / DFAM

No description available.

No description available.

I denna studie analyserar vi numeriska metoder som beskriver koncentrationen av ytaktiva ämnen (surfaktanter). Dessa surfaktanter befinner sig i olösliga vätskor som separeras av ett tidsberoende gränssnitt som påverkas av ett givet hastighetsfält. Surfaktanter har stor inverkan på vätskesystem på grund av deras förmåga att sänka ytspänningen mellan två vätskor, exempelvis kan dessa användas för att göra olja mer lösbart i vatten. En vanlig strategi vid implementering av finita elementmetoder (FEM) för att lösa liknande problem är att låta beräkningsnätet anpassas efter den tidsberoende domänen, vilket kräver omdiskretisering i varje tidssteg. Således har så kallade oanpassade metoder, som inte kräver att beräkningsnätet anpassas efter domänen, blivit ett användbart alternativ till standard FEM för komplicerade tidsberoende problem. Oanpassade metoder använder ett kontant bakgrundsnät som täcker beräkningsdomänen i varje tidssteg. I denna studie tillämpar vi skurna finita elementmetoder (CutFEM) på två olika matematiska modeller av surfaktanterna. I den första modellen betraktas endast surfaktantkoncentrationen i bulkgeometrin, där koncentrationen ges av en konvektion-diffusionsekvation. I den andra modellen löses istället två ekvationer som är kopplade till varandra (en i bulkdomänen och en på ytan) genom en icke-linjär kopplingsmodell.

This thesis introduces high-voltage approaches that are implemented in an analog Hall-effect sensor interface. This interface has been realized in a modified 5V 0.6um CMOS process using 40V high-voltage MOS transistors that do not affect low-voltage device functionality. These circuits include a high-voltage, low-offset current sense amplifier, which achieves a common-mode input range that is within a Vtp of Vdd using a bulk-driven differential input stage. The amplifier also uses high voltage cascode devices to protect low-voltage devices that have been placed in critical matching areas to achieve a low input offset voltage of 500uV without the use of trim. A short to battery architecture is also discussed which uses a bulk-driven comparator and a PMOS blocking technique and allows for a reliable short to battery breakdown voltage without using a series blocking diode. Integration of these blocks into a standard CMOS process leads to cost savings as additional devices such as data converters and microprocessors are combined with the Hall-effect sensor interface.

A systematic study of iron-based binary and multi-component alloys was undertaken to study the structural evolution in these powders as a function of milling time during mechanical alloying. Blended elemental powders of Fe100-XBX (where x = 5, 10, 17, 20, 22, 25, 37.5 and 50 at. %) and a bulk metallic glass (BMG) composition (Fe60Co8Zr10Mo5W2B15) were subjected to mechanical alloying in a SPEX 8000 mixer mill. X-ray diffraction technique was employed to study the phase evolution, crystallite size, lattice strain and also to determine the crystal structure(s) of the phases. Depending on the milling time, formation of supersaturated solid solutions, intermetallics, and amorphous phases was noted in the binary Fe-B powder mixtures. A maximum of about 22 at. % B was found to dissolve in Fe in the solid state, and formation of FeB and Fe2B intermetallics was noted in some of the powder blends. However, an interesting observation that was made, for the first time, related to the formation of a crystalline phase on continued milling of the amorphous powder in the BMG composition. This phenomenon, termed mechanical crystallization, has been explored. Reasons for the mechanical crystallization of the amorphous powder using the X-ray diffraction and electron microscopy methods have been discussed. External heat treatments of the milled powder were also conducted to study the complete crystallization behavior of the amorphous phase. Preliminary attempts were made to consolidate the milled BMG powder to bulk shape by hot isostatic pressing (HIP) and magnetic compaction techniques. Full densification was not achieved. Nanoindentation and microhardness tests were performed to characterize the mechanical properties of the glassy alloy. Nanoindentation results gave an elastic modulus of 59 GPa, lower than the expected value of 184 GPa; due to the presence of porosity in the consolidated sample. Optimization of the consolidation parameters is required to achieve a fully dense material.

Bulk Metallic Glasses (BMGs), also known as amorphous metals, are of considerable scientific and commercial interest due to their random or chaotic structure. Given their potential use as engineering materials, there is a concomitant need to establish their mechanical properties. However, BMGs are not conveniently available in sufficient volumes (especially experimental and combinatorial compositions), making property determination via conventional tensile or compression testing problematic. Instrumented indentation is ideally suited for this purpose because the testing requires only small sampling volumes and can probe multiaxial deformation characteristics at various length scales. In this technique, conducted generally on a sub-micron regime, the depth of penetration of an indenter, usually a diamond, is measured as a function of the applied load and expressed graphically as load (P) - displacement (h) curves from which a host of mechanical properties can be extracted and studied. In this work, a methodology for using instrumented indentation at nano- and micro- scales to determine the mechanical response of BMGs was developed and implemented. The implementation primarily focused on deformation in the elastic regime but included preliminary results related to the onset of inelastic deformation. The methodology developed included calibration techniques, formulations to extract the machine compliances, verifications using standards and verification for uniqueness of instrument deformation under a spherical indenter. The methodology was different for the two platforms used based on the load-depth response characteristics of the instrument. In the case of the Micro Test platform, the load-depth response of the instrument was linear. In the case of the Nano Test platform, the instrument load-depth response followed a 3/2 power law, representative of Hertzian behavior. The load-depth response of the instrument was determined by subtracting the theoretical response from the corresponding raw load-depth response obtained by elastically indenting a standard steel specimen of known modulus. The true response of the sample was then obtained by subtracting the instrument's response from the corresponding uncorrected load-depth response (raw data). An analytical model to describe the load-train compliance was developed. The methodology was verified using quartz and tungsten standards. Indentation experiments were conducted on Zr41.25Ti13.75Cu12.5Ni10Be22.5 (Vitreloy 1), Cu60Hf25Ti15, Cu60Zr30Ti10 and Fe60Co7Zr10Mo5W2B16 bulk metallic glasses using spherical indenters with diameters 2.8 mm and 100 [micro]m. The spherical geometry results in a simpler stress distribution under the indenter (when compared to a sharp geometry) and furthermore by recourse to spherical indenters the onset of plastic deformation was delayed. In the case of the Zr-based BMG, the experiments showed that the elastic response did not depend on the diameter of the indenter used indicative of the absence of residual stresses in the sample. Large scale plastic deformation was observed when the sample was indented using a smaller diameter indenter. Log scale analysis (i.e., examining the results on a log load vs. log depth response to check for deviation from Hertzian behavior) showed a deviation from a 3/2 fit indicating a deviation from elastic behavior. The onset implied a yield strength value of ~ 4 GPa, higher than the value reported in the literature (~ 2 GPa). Hence, it is believed that the first signs of plastic deformation occurred at lower loads than the predicted loads from the log scale analysis procedure and is expected to occur as discrete bursts. Discrete plastic events or "pop-ins" were observed in the load-depth indentation responses under quasistatic loading conditions, which were believed to be associated with shear band activity. An attempt was made to formulate a mathematical model based on three yield criteria (Drucker-Prager, Mohr-Coulomb and von Mises). Based on the von Mises predictions and comparable experiments on a quartz standard, it was established that the pop-ins observed were real and not an instrument artifact. Multiple load cycles following partial unload experiments showed that the pop-ins affected the subsequent indentation response. The moduli and the yield strength values obtained for the Cu-based BMGs were comparable to the values reported in the literature. There was significant scatter in the indentation data from the Fe-based BMG. Porosity and lack of 100 % compaction were believed to be the reasons for scatter in the data. The financial support of NSF through grant DMR 0314212 is gratefully acknowledged.