The combined finite-discrete element method (FEM/DEM) has been used to simulate processes of brittle fracturing and associated seismicity. With the newly extended FEM/DEM algorithm, two topics involving rock mechanics and geophysics are investigated. In the first topic, a velocity-weakening law is implemented to investigate the initiation of frictional slip, and an innovative method that incorporates surface roughness with varying friction coefficients is introduced to examine the influences of surface roughness. Simulated results revealed detailed responses of stresses to the propagation of the slip front. In the second topic, acoustic activities induced in confined compression tests are simulated and quantitatively studied using the internal monitoring algorithm in FEM/DEM. It is shown that with increasing confinement, AE events are spatially more concentrated and temporally more separated, accompanied by a decreasing b-value. Moreover, interesting correlation between orientations of cracks and the mechanical behavior of the rock was observed.

The combined finite-discrete element method (FEM/DEM) has been used to simulate processes of brittle fracturing and associated seismicity. With the newly extended FEM/DEM algorithm, two topics involving rock mechanics and geophysics are investigated. In the first topic, a velocity-weakening law is implemented to investigate the initiation of frictional slip, and an innovative method that incorporates surface roughness with varying friction coefficients is introduced to examine the influences of surface roughness. Simulated results revealed detailed responses of stresses to the propagation of the slip front. In the second topic, acoustic activities induced in confined compression tests are simulated and quantitatively studied using the internal monitoring algorithm in FEM/DEM. It is shown that with increasing confinement, AE events are spatially more concentrated and temporally more separated, accompanied by a decreasing b-value. Moreover, interesting correlation between orientations of cracks and the mechanical behavior of the rock was observed.

Atmospheric particles can affect climate directly, by scattering solar radiation, or indirectly, by acting as the seed upon which cloud droplets form. These clouds can then cool the earth's surface by reflecting incoming sunlight. In order to constrain the large uncertainties in predicting the ultimate effect of aerosol on climate, the sources of atmospheric particles and their subsequent ability to turn into cloud droplets needs to be better understood. This thesis addresses two parts of this issue: the sources of Arctic aerosol and the hygroscopicity of continental organic aerosol. Small particles were observed in Baffin Bay during September 2008 that coincided with high atmospheric and ocean surface dimethyl sulphide (DMS) concentrations suggesting that the aerosol formed from oceanic sources. An aerosol microphysics box model confirmed that local DMS could have produced the observed particles. In addition, the particle chemical composition was measured using aerosol mass spectrometry in the central Arctic Ocean in August 2008 and particles were found to be 43% organic and 46% sulphate. Factor analysis further apportioned the aerosol mass to marine biogenic and continental sources 33% and 36% of the time, respectively, with the source of the remaining mass unidentified. The second part of the study parameterises the hygroscopicity of the ambient organic aerosol fraction (κorg) at Egbert, Ontario and Whistler, British Columbia. This was done using two methods: 1) by assuming that the oxygenated organic component was hygroscopic and that the unoxygenated organic component was non-hygroscopic, κ of the oxygenated component was found to be 0.22 ± 0.04, and 2) by assuming that κorg varied linearly with the atomic oxygen to atomic carbon ratio, it could be parameterised as κorg = (0.29 ± 0.05) × (O/C). Calculations predict that knowing κorg is important in urban, semi-urban, and remote locations whenever the inorganic mass fraction is low.

Atmospheric particles can affect climate directly, by scattering solar radiation, or indirectly, by acting as the seed upon which cloud droplets form. These clouds can then cool the earth's surface by reflecting incoming sunlight. In order to constrain the large uncertainties in predicting the ultimate effect of aerosol on climate, the sources of atmospheric particles and their subsequent ability to turn into cloud droplets needs to be better understood. This thesis addresses two parts of this issue: the sources of Arctic aerosol and the hygroscopicity of continental organic aerosol. Small particles were observed in Baffin Bay during September 2008 that coincided with high atmospheric and ocean surface dimethyl sulphide (DMS) concentrations suggesting that the aerosol formed from oceanic sources. An aerosol microphysics box model confirmed that local DMS could have produced the observed particles. In addition, the particle chemical composition was measured using aerosol mass spectrometry in the central Arctic Ocean in August 2008 and particles were found to be 43% organic and 46% sulphate. Factor analysis further apportioned the aerosol mass to marine biogenic and continental sources 33% and 36% of the time, respectively, with the source of the remaining mass unidentified. The second part of the study parameterises the hygroscopicity of the ambient organic aerosol fraction (κorg) at Egbert, Ontario and Whistler, British Columbia. This was done using two methods: 1) by assuming that the oxygenated organic component was hygroscopic and that the unoxygenated organic component was non-hygroscopic, κ of the oxygenated component was found to be 0.22 ± 0.04, and 2) by assuming that κorg varied linearly with the atomic oxygen to atomic carbon ratio, it could be parameterised as κorg = (0.29 ± 0.05) × (O/C). Calculations predict that knowing κorg is important in urban, semi-urban, and remote locations whenever the inorganic mass fraction is low.

ABSTRACT A study is carried out on the production of aluminum foams via powder processing. The study deals mainly with the effect of TiH2 particle size on the process of foaming. Mainly two TiH2 particle sizes were used / namely 27,5 &amp / #61549 / m and 8,5 &amp / #61549 / m. Foaming experiments were carried out at temperatures between 675oC &ndash / 840oC. The viscosity of the system is adjusted by controlled addition of Al2O3. The study shows that choice of foaming agent size is influential in the foaming process. With the use of fine foaming agent, temperatures in excess of 800oC would be required for successful foaming. The study further showed that the relation between foaming and viscosity was also dependent on the particle size. Viscosity of 2.3 mPa.s was found to be a limiting value for successful foaming with fine foaming agent. This value appears to increase with increasing particle size. An analysis is presented with regard to temperature dependence of foaming which takes into account the effect of particle size.

The confined impinging jet reactor gives efficient mixing performance as required for fast reactions. In this work the mixing performance of CIJR is characterized through three measures: estimates of the energy dissipation, micromixing efficiency based on the yield of a homogeneous (iodide-iodate) reaction and particle size resulting from a heterogeneous (iron oxide) precipitation reaction. Whereas product yield and energy dissipation are used to test operational robustness of CIJR, iron oxide model system is used to study the effect of feed flow rate (mixing) and reactant concentration on precipitate agglomerate size. Mixing and concentration effects on nucleation, particle growth and particle agglomeration are tracked to understand the agglomeration process. Various types of stabilizers and additive concentrations to limit particle agglomeration are also tested. Effects of in situ and post-reaction sonication on agglomerate size are also investigated. Efforts are made to determine variations in mixing efficiency the operational robustness of the scale-up (2X and 4X) geometries. Also efforts are made to identify scaling parameters and the limit on geometric scale-up for good mixing performance. Energy dissipation is found to vary between 20 W/kg and 6800 W/kg in CIJR and decreases on scale-up at constant Reynolds number. The operation of the CIJR and the scale-up geometries is robust to changes in flow rate, exhibiting stable performance up to 30% difference in inlet flow rates. Reliable mixing performance is obtained until 2X scale-up, while at low flow rates, the jets fail to impinge in 4X scale-up, and sometimes failing to fill the reactor volume. Iron oxide primary and agglomerate particles are seen to vary with flow rate and reactant concentrations. Largest primary particles (and smallest agglomerates) are obtained at high flow rates and high reactant concentrations, which indicate to size dependent agglomerative tendency of the primary particles. Stabilizers added in situ see limited success. Post-reaction sonication is helpful in dispersing soft agglomerates, but in situ sonication shows no significant reduction in agglomerate size with or without stabilizer. Primary particles are understood to agglomerate due to collisions induced by Brownian motion, simple shear and velocity fluctuations in turbulent flows. These collision mechanisms operate at different length scales in the fluid mass. / Chemical Engineering

Solid-state amorphization of a crystalline solid to an amorphous phase is extensively studied as a first order phase transition at low temperature for almost thirty years. In this dissertation, we report the recent progress on phenomenological models employed for thermodynamic description of macroscopic systems and fluctuations and nucleation of mesoscopic inhomogeneous systems in binary solid solutions under polymorphic constraints with no long-range diffusion involved. Based on our understanding on atomic picture of solid-state amorphization in binary solid solutions, we propose a Landau free energy to describe amorphization as the first order phase transition. The order parameter is defined which represents the loss of long-range translational order. The elastic strain field induced by composition disorder plays the important role through the bilinear coupling with the order parameter. Elastic softening and amorphization happen simultaneously. From the similarity between the melting and amorphization, we use the temperature and composition as two external variables and treat solid-state amorphization as low temperature melting under polymorphic constraints. For homogeneous system, the phase diagrams for endothermic melting and exothermic melting are built separately and the corresponding thermodynamic quantities are presented. A microscopic homogeneous nucleation mechanism is proposed conceptually in binary solid solutions under polymorphic constraints. The formation of an amorphous embryo is initiated from the composition modulation in the crystal state and a subsequent polymorphous nucleation within the as-formed heterophase fluctuation. This homogeneous nucleation path is thought to be associated with the nonlinear energy localization mechanism connected with the localized large-amplitude excitations of atoms, which are induced by nonlinear and disorder. A Landau-Ginzburg free energy is constructed to describe the critical nucleus and the growth of the new phase in one-dimensional systems. Analytical and numerical methods contribute to the understanding the fluctuations and nucleation processes. Size-dependent melting and amorphization in nanosolids are investigated. Two models are proposed for nanocrystalline solid solutions to glass transformations. Based on the thin film model with finite thickness, we build one-dimensional Landau-Ginzburg approach, which includes surface contribution and size dependence, and numerical results do show similarity with experimentsâ results qualitatively.

Flip Chip in Package (FCIP) has been developed to achieve the assembly process with area array interconnects. Particularly, a high I/O count coupled with finer pitch area array interconnects structured FCIP can be achieved using no-flow underfill assembly process. Using the assembly process, a high, stable yield assembly process recently reported with eutectic lead-tin solder interconnections, 150 µm pitch, and I/O counts in excess of 3000. The assembly process reported created a large number of voids among solder interconnects in FCIP. The voids formed among solder interconnections can propagate, grow, and produce defects such as solder joint cracking and solder bridging. Moreover, these voids can severely reduce reliability performance. Indeed, many studies were conducted to examine the void formation in FCIP. Based on the studies, flip chip geometric design, process conditions, and material formulation have been considered as the potential causes of void formation. However, the present research won't be able to identify the mechanism of void formation, causing a lot of voids in assembly process without consideration of chemical reaction in the assembly process with a fine-pitch, high I/O density FCIP. Therefore, this research will present process technology necessary to achieve high yields in FCIP assemblies using no-flow underfills and investigate the underlying problem of underfill void formation in these assemblies. The plausible causes of void formation will be investigated using experimental techniques. The techniques will identify the primary source of the void formation. Besides, theoretical models will be established to predict the number of voids and to explain the growth behavior of voids in the FCIP. The established theoretical models will be verified by experiments. These models will validate with respect to the relationship between process parameters to achieve a high yield and to minimize voids in FCIP assemblies using no-flow underfill materials regarding process as well as material stand points. Eventually, this research provides design guideline achieving a high, stable yield and void-free assembly process.

The ability to generate three dimensional (3D) microstructures in solids is of great importance in understanding their true nature, as it eliminates speculation about the spatial distribution of features associated with conventional two dimensional (2D) imaging techniques. There are several recently-developed 3D techniques for determining the spatial distribution of microstructural features, each with a given resolution. There is considerable interest in the development of a specific serial sectioning methodology, termed 3D electron backscatter diffraction (3D-EBSD), which combines a focused ion beam (FIB) with EBSD interfaced to a field emission gun scanning electron microscope. Here, FIB is used as a serial sectioning device for cutting parallel slices of single- and multi-phase materials with a site-specific accuracy of up to 50 nm. Each consecutive slice is mapped by EBSD and the complete dataset combined using advanced computer algorithms to generate a volume of a material whereby the true crystallographic features can be analyzed at submicron resolution. The aims of the thesis was to develop 3D-EBSD into a powerful materials analysis tool and use it to resolve several issues concerning the nature of the deformed state and the nucleation and the growth behaviour of recrystallizing grains. The study commenced with an investigation into the effect of material type (restricted to face centred cubic AI, Cu and Au metallic crystals), FIB milling conditions and EBSD software variables on the quality of EBSD patterns generated on ion-milled surfaces of these materials. The effect of material type on EBSD pattern quality following FIB milling was found to be significant with relatively poor quality EBSD patterns obtained for metals of low atomic number. It was demonstrated, particularly for the high atomic number metals, that moderate FIB milling currents (~1-5nA) generated good quality EBSD maps from a given ion-milled surface. This preliminary work was necessary for balancing the time required for serial sectioning during 3D-EBSD and the generation of sufficient quality EBSD maps from each ion-milled surface. The outcomes of this investigation were applied to two major 3D-EBSD investigations on the microstructural and crystallographic characteristics of: (i) deformation features generated in a cold rolled interstitial free (IF) steel, with particular emphasis on the formation of microbands; and (ii) recrystallization of a cold rolled nickel alloy containing coarse (>1 ??m) silica particles, with particular attention given to the generation of particle deformation zones and their influence on nucleation and growth of recrystallizing grains including particle stimulated nucleation (PSN), twin formation during PSN and the growth behaviour of various types of grain boundary into the deformation microstructure. The foregoing 3D-EBSD studies were significant as they revealed various microstructural and crystallographic features not usually clearly evident in conventional 2D micrographs obtained by either EBSD or optical metallography. For example, the technique demonstrated that microbands in cold rolled IF steel consist of irregular curved surfaces that reconcile findings that microbands straight and aligned parallel to slip planes when viewed in normal direction-rolling direction sections but are wavy in transverse direction-rolling direction sections. Three slip planes were found within the angular range of the curved surface of the microband, which indicates that multiple slip planes are operative during deformation. The work also showed the influence of particle diameter on the misorientations generated within particle deformation zones and clearly showed that particle stimulated nucleation (PSN) occurred at particles greater than 1.5-2 ??m. It was observed that PSN in the nickel sample also generates contiguous grains separated by both coherent and incoherent twin boundaries and, on further growth of these grains into the matrix, the coherent boundary dominates and remains parallel to the primary growth direction of the grains.

Bibliography: leaves 228-237 / xii, 287 leaves : ill ; 30 cm. / Title page, contents and abstract only. The complete thesis in print form is available from the University Library. / Thesis (Ph.D.)--University of Adelaide, Dept. of Chemical Engineering, 1990