Functional electrical stimulation (FES) devices have direct applications in the realm of rehabilitation engineering, physiotherapy, occupational therapy and medicine for research, diagnostic and therapeutic purposes. This thesis presents a novel electrical stimulator for use in a FES system. The stimulator produces regulated current pulses using two switched mode power supplies (SMPS) in series. The first power stage - a flyback converter - steps up the supply voltage using primary side digital control. The second power stage is a buck converter with output current hysteretic control. An output switched capacitor circuit shapes the current pulses. All pulse variables are programmable and various pulses can be formed for virtually any FES application. Compared to previous FES devices, the pulses generated here are sharper, have faster rise time and the amplitude and temporal characteristics are more tightly regulated. A single channel prototype system is implemented and experimental results are shown.

Functional electrical stimulation (FES) devices have direct applications in the realm of rehabilitation engineering, physiotherapy, occupational therapy and medicine for research, diagnostic and therapeutic purposes. This thesis presents a novel electrical stimulator for use in a FES system. The stimulator produces regulated current pulses using two switched mode power supplies (SMPS) in series. The first power stage - a flyback converter - steps up the supply voltage using primary side digital control. The second power stage is a buck converter with output current hysteretic control. An output switched capacitor circuit shapes the current pulses. All pulse variables are programmable and various pulses can be formed for virtually any FES application. Compared to previous FES devices, the pulses generated here are sharper, have faster rise time and the amplitude and temporal characteristics are more tightly regulated. A single channel prototype system is implemented and experimental results are shown.

Power management components can be found in a host of different applications ranging from portable hand held gadgets to modern avionics to advanced medical instrumentations, among many other applications. Low-dropout (LDO) linear regulators are particularly popular owing to their: ease of use, low cost, high accuracy, low noise, and high bandwidth. With all its glory, however, it tends to underperform switched-mode power supplies (SMPS) when with comes to power conversion efficiency, although the later generates a lot of ripple at its output. With the growing need to improve system efficiency (hence longer battery life) without degrading system performance, many high end (noise sensitive) applications such as data converters, RF transceivers, precision signal conditioning, among others, use high efficiency SMPS with LDO regulators as post-regulators for rejecting the ripple generated by SMPS. This attribute of LDO regulators is known as power supply rejection (PSR). With the trend towards increasing switching frequency for SMPS, to minimize PC board real estate, it is becoming ever more difficult for LDO regulators to suppress the associate high frequency ripple since at such high frequencies, different parasitic components of the LDO regulator start to deteriorate its PSR performance. There have been a handful of different techniques suggested in the literature that can be used to achieve good PSR performance at higher frequencies. However, each of these techniques suffers from a number of drawbacks ranging from reduced efficiency to increased cost to increased solution size, and with the growing demand for higher efficiency and smaller power supplies, these techniques have their clear limitations. The objective of this research project is to develop a novel current-mode LDO regulator that can achieve good high frequency PSR performance without suffering from the afore mentioned drawbacks. The proposed architecture was fabricated using a proprietary 1.5 um Bipolar process technology, and the measurement results show a PSR improvement of 20dB (at high frequencies) over conventional regulators. Moreover, the proposed LDO regulator requires a small 15nF output capacitor for stability, which is far smaller than some of the currently used techniques.

This diploma thesis deals with design of welding power supply for MIG / MAG and MMA technique with continuous output current 120 A. The first, theoretical part is devoted to welding process technology, physical characteristics of electric arc and description of individual welding methods. The thesis also deals with the concept of power converter. The design of the switched-mode power supply is based on a full bridge topology. In order to implement advanced controls of welding power supply, the ARM Cortex M4 microprocessor was selected. Due to the large power consumption of the stepper motor for drive the welding wire, an auxiliary switched-mode power supply was also implemented. The documentation describing the realization of the welding power supply and the results of the measurements are in the last part of the thesis. The welding power supply was successfully revived and reached nominal parameters. Inert gas welding has not been tested yet, due to lack of time caused by extensive work in order to complete mechanical realization.

The aim of my master’s thesis is the design and implementation of laboratory power supply with output parameters 0-25V and 0-2A and options to manage this resource by elements of the front panel or via a computer control program. Content is the theoretical analysis of the possibility of subsequent theoretical sources suggesting that it verified on the prototype laboratory resources.

Oliver Tambo Institute of Governance and Policy Studies / MPM

The project shows the problems of power supply in electrical engineering. It describes the general parameters of these types of supplies and presents their characteristics. Based on these findings, it is also focused on the selection of specific elements of the laboratory supply, to reach the given parameters. It contains the recalculations of the parameters of other additional components. The overall scheme of the supply is divided into several blocks, thematically corresponded to subchapters. According to the accomplished concept the laboratory supply is realized and its parameters had been tested. Projects results are assessed at the end.

With rising fuel prices, increasing electrification, and imminent fines on CO2 emission within the EU, the requirement for energy and cost efficient supply concepts is becomingmore and more important in the automotive industry. This thesis presents an assessmentof, and improvement for energy and cost efficient power supply concepts for low-end automotiveand light e-mobility electronic control units, containing small µCs, and analogand logic components. Specifically, linear regulators, synchronous and non-synchronous buck converters, andswitched capacitor converters are investigated and assessed theoretically. The mostpromising concept, namely a discrete buck converter, is further studied using theoreticalassessment, experiment, and simulations. The key result of this work is a concept for replacing commonly used linear regulatorsin small electronic control units (ECUs) by a more efficient supply with only a smallcost adder. Specifically, since no low-end switched converter ICs are available today, wedeveloped a buck converter with discrete control circuit. This concept provides a cheap,yet efficient alternative to linear regulators for a wide range of applications. In addition,the application of this concept is supported by component selection criteria, and also bythe developed simulation models.

This master´s thesis describes switch mode power supply and discusses the design of its individual parts. It also contains a simulation of the power part of the converter and a reseach in the area of DC/DC converters.

This thesis is about theory of switching power supplies and about a specific solution of switching power supply for electron microscope. In the beginning of the thesis are mentioned various solutions of part blocks of switching power supplies, their advanteges and disadvanteges, and their suitability for electron microscopy. In the next part of the thesis are described requirements and design scheme of switching power supply for scanning part of electron microscope. The thesis i also about technical solution and practical testing of the switching power supply and verification of its functions.