Microtruss cellular materials have large internal surface areas and small cross-sectional strut dimensions, permitting surface modification to substantially enhance their mechanical performance. For instance, a ~400% increase in compressive strength with virtually no weight penalty can be induced by a hard anodized Al2O3 ceramic coating of only ~50 µm thickness. The present study seeks the optimal architecture of these composites by exploring three research challenges: architecture and degree of forming are interdependent due to stretch-forming, architecture and the material properties are interdependent due to work-hardening, and ceramic structural coatings add design complexity. Theoretical predictions and architectural optimizations demonstrated a potential weight reduction of ~3% to ~60% through the increase of internal truss angle for both annealed and work-hardened microtruss cores. While further validation is needed, experimental evidence in this study suggested the collapse in ceramic-aluminum microtruss composites could be considered as a mixture of composite strut global buckling and oxide local shell buckling mechanisms.

The improvement in mechanical strength offered by ultra fine- (UF) and nanocrystalline (NC) sized grains is very attractive for potential applications of structural metals. Accumulative Roll-Bonding (ARB) is one of the promising new techniques for producing bulk UF grained metals. There are numerous reports on the monotonic mechanical behavior of various ARBed metals, however there are few, if any, on the cyclic deformation behavior of such metals. The primary objective of this study is to investigate the cyclic deformation behaviour and the related micro-mechanisms of ARBed metals from a fundamental perspective. To achieve this, the microstructure and the deformation behavior of commercial purity aluminum, OFHC copper, and DLP copper after ARB processing have been systematically characterized. The as-ARBed microstructure is found to be composite natured, with constituents of different grain sizes. The three constituents are: (i)UF grained matrix, (ii)NC primary discontinuities, and (iii)conventional sized pre-existing coarse grains. Due to this composite nature, three different cyclic strain accommodation mechanisms were found in the ARBed OFHC copper: (i)conventional dislocation patterns in the large grains, (ii)reactivation of pre-existing shear bands, and (iii)stress/strain driven grain coarsening at sites of strain localization. The order of activation of the mechanisms can be described with a composite approach based on activation energy. The occurrence of grain coarsening is the major contributor to the cyclic softening response observed in OFHC copper. Conversely, the lesser extent of cyclic softening in the other two metals is likely due to the higher microstructure stability of the initial as-ARBed materials. The microstructure stability is believed to be the primary influencing factor for the extent of grain coarsening and cyclic softening. The applied cyclic plastic strain is a secondary influencing factor, although this is generally overshadowed by the limitation of grain coarsening due to the short cyclic lifespan of these metals. The occurrences of shear banding and grain coarsening reported in the present ARBed metals are similarly reported for UF grained metals from other processes, e.g. ECAPed metals. Thus, its relationship to the cyclic deformation response and governing factors are believed to be applicable for UF grained metals in general.

It has been conventional to simplify the thermo-mechanical modeling of solder joints by omitting the primary (transient) contributions to total creep deformation, assuming that secondary (steady-state) creep strain is dominant and primary creep is negligible. The error associated with this assumption has been difficult to assess because it depends on the properties of the solder joint and the temperature-time profile. This research examines the relative contributions of primary and secondary creep in Sn3.8Ag0.7Cu solder using the constant load creep and stress relaxation measurements for bulk tensile specimens and the finite element analysis of a chip resistor (trilayer) solder joint structure that was thermally cycled under multiple temperature ranges and ramp rates. It was found that neglect of primary creep can result in errors in the predicted stress and strain of the solder joint. In turn, these discrepancies can lead to errors in the estimation of the solder thermal fatigue life due to the changing proportion of primary creep strain to total inelastic strain under different thermal profiles. The constant-load creep and stress relaxation data for Sn3.8Ag0.7Cu span a range of strain rates 10(-8) 1/s < strain rate < 10(-4) 1/s, and temperatures 25°C, 75°C and 100°C. Creep and stress relaxation measurements show that transient creep caused faster strain rates during stress relaxation for a given stress compared to the corresponding minimum creep rate from constant-load creep tests. The extent of strain hardening during primary creep was a function of temperature and strain rate. A constitutive creep model was presented for Sn3.8Ag0.7Cu that incorporates both transient and steady-state creep to provide agreement for both creep and stress relaxation data with a single set of eight coefficients. The model utilizes both temperature compensated time and strain rate to normalize minimum strain rate and saturated transient creep strain, thereby establishing equivalence between decreased temperature and increased strain rate. The apparent activation energy of steady-state creep was indicative of both dislocation core and bulk lattice diffusion was the most sensitive model parameter. A saturation threshold was defined that distinguishes whether primary or secondary creep is dominant under either static or variable loading.

It has been conventional to simplify the thermo-mechanical modeling of solder joints by omitting the primary (transient) contributions to total creep deformation, assuming that secondary (steady-state) creep strain is dominant and primary creep is negligible. The error associated with this assumption has been difficult to assess because it depends on the properties of the solder joint and the temperature-time profile. This research examines the relative contributions of primary and secondary creep in Sn3.8Ag0.7Cu solder using the constant load creep and stress relaxation measurements for bulk tensile specimens and the finite element analysis of a chip resistor (trilayer) solder joint structure that was thermally cycled under multiple temperature ranges and ramp rates. It was found that neglect of primary creep can result in errors in the predicted stress and strain of the solder joint. In turn, these discrepancies can lead to errors in the estimation of the solder thermal fatigue life due to the changing proportion of primary creep strain to total inelastic strain under different thermal profiles. The constant-load creep and stress relaxation data for Sn3.8Ag0.7Cu span a range of strain rates 10(-8) 1/s < strain rate < 10(-4) 1/s, and temperatures 25°C, 75°C and 100°C. Creep and stress relaxation measurements show that transient creep caused faster strain rates during stress relaxation for a given stress compared to the corresponding minimum creep rate from constant-load creep tests. The extent of strain hardening during primary creep was a function of temperature and strain rate. A constitutive creep model was presented for Sn3.8Ag0.7Cu that incorporates both transient and steady-state creep to provide agreement for both creep and stress relaxation data with a single set of eight coefficients. The model utilizes both temperature compensated time and strain rate to normalize minimum strain rate and saturated transient creep strain, thereby establishing equivalence between decreased temperature and increased strain rate. The apparent activation energy of steady-state creep was indicative of both dislocation core and bulk lattice diffusion was the most sensitive model parameter. A saturation threshold was defined that distinguishes whether primary or secondary creep is dominant under either static or variable loading.

Acute lung injury (ALI) is a major cause of mortality after lung transplantation. Recent studies indicate protein kinase C delta (PKCδ) could be an effective target to treat ALI. We have developed a gold nanoparticle (GNP)-peptide hybrid that can inhibit PKCδ signaling. PKCδ inhibitor peptide (PKCi) and 95P2P4 stabilizing peptides were conjugated onto GNP. Physicochemical properties of the nanoformulations were examined. A lung transplant-simulated cell culture model was used to evaluate therapeutic efficacy in vitro. A pulmonary ischemia-reperfusion (IR) model was used to test therapeutic efficacy in vivo. GNP-Peptide hybrids showed good stability with high cellular uptake. GNP-PKCi formulations demonstrated anti-inflammatory and anti-apoptotic effects in vitro. When administered to rats under IR stress, GNP-PKCi formulation improved blood oxygenation, reduced pulmonary edema and histological lung injury. In conclusion, we have successfully formulated a clinically-applicable nanoparticle with therapeutic potential to ameliorate lung injury and inflammation. Our formulation strategy could be used to deliver other peptide-based drugs.

Acute lung injury (ALI) is a major cause of mortality after lung transplantation. Recent studies indicate protein kinase C delta (PKCδ) could be an effective target to treat ALI. We have developed a gold nanoparticle (GNP)-peptide hybrid that can inhibit PKCδ signaling. PKCδ inhibitor peptide (PKCi) and 95P2P4 stabilizing peptides were conjugated onto GNP. Physicochemical properties of the nanoformulations were examined. A lung transplant-simulated cell culture model was used to evaluate therapeutic efficacy in vitro. A pulmonary ischemia-reperfusion (IR) model was used to test therapeutic efficacy in vivo. GNP-Peptide hybrids showed good stability with high cellular uptake. GNP-PKCi formulations demonstrated anti-inflammatory and anti-apoptotic effects in vitro. When administered to rats under IR stress, GNP-PKCi formulation improved blood oxygenation, reduced pulmonary edema and histological lung injury. In conclusion, we have successfully formulated a clinically-applicable nanoparticle with therapeutic potential to ameliorate lung injury and inflammation. Our formulation strategy could be used to deliver other peptide-based drugs.

The current study characterizes the mechanical and biodegradation properties of a polycarbonate polyurethane (PU) electrospun nanofiber scaffold intended for use in the growth of a tissue engineered annulus fibrosus (AF) intervertebral disc component. Both the tensile strength and initial modulus of aligned scaffolds were higher than those of random scaffolds and remained unaffected during a 4 week biodegradation study, suggesting a surface-mediated degradation mechanism. The resulting degradation products were non-toxic. Confined compressive mechanical force of 1kPa, was applied at 1Hz to in vitro bovine AF tissue grown on the scaffolds to investigate the influence of mechanical force on AF tissue production, which was found to decrease significantly at 72 hours relative to 24 hours, independent of any effects from mechanical forces. Overall, the consistent rate of PU degradation, along with mechanical properties comparable to those of native AF tissue, and the absence of cytotoxic effects, make this polymer suitable for further investigation for use in tissue-engineering the AF.

This work investigates fabrication methods of nickel oxide thin films and their use in organic electronics. Two fabrication techniques were studied: UV-ozone oxidation of pure nickel films and reactive RF magnetron sputtering. The former was used to produce Ni/Ni2O3 bi-layer anodes to use as a substitute for the de facto standard ITO anode. OLEDs fabricated using Ni/Ni2O3 bi-layer anodes exhibited comparable device performance to standard ITO devices. UV-ozone oxidation was also used to fabricate Ni2O3 buffer layers for OPVs. Solar cells fabricated using Ni2O3 coated ITO exhibited an enhanced power conversion efficiency of up to 90%. RF magnetron sputtering was used to produce NiOx buffer layers with tunable conductivity and optical transparency for OPVs. Solar cells fabricated using NiOx coated ITO exhibited an enhanced power conversion efficiency of up to 60%. Nickel oxide films have been characterized with various techniques: sheet resistance measurements, optical transmission, XPS, UPS, AFM, and TEM.

Three-dimensional macroporous structures (‘opals’ and ‘inverse opals’) can be produced by colloidal crystal templating, one of the most intensively studied areas in materials science today. There are several potential advantages of lithium-ion battery electrodes based on inverse opal structures. High electrode surface, easier electrolyte access to the bulk of electrode and reduced lithium diffusion lengths allow higher discharge rates. Highly open structures provide for better mechanical stability to volume swings during cycling. Silicon is one of the most promising anode materials for lithium-ion batteries. Its theoretical capacity exceeds capacities of all other materials besides metallic lithium. Silicon is abundant, cheap, and its use would allow for incorporation of microbattery production into the semiconductor manufacturing. Performance of silicon is restricted mainly by large volume changes during cycling. The objective of this work was to investigate how the inverse opal structures influence the performance of silicon electrodes. Several types of silicon-based inverse opal films were synthesised, and their electrochemical performance was studied. Amorphous silicon inverse opals were fabricated via chemical vapour deposition and characterised by various techniques. Galvanostatic cycling of these materials confirmed the feasibility of the approach taken, since the electrodes demonstrated high capacities and decent capacity retentions. The rate performance of amorphous silicon inverse opals was unsatisfactory due to low conductivity of silicon. The conductivity of silicon inverse opals was improved by crystallisation. Nanocrystalline silicon inverse opals demonstrated much better rate capabilities, but the capacities faded to zero after several cycles. Silicon-carbon composite inverse opal materials were synthesised by depositing a thin layer of carbon via pyrolysis of a sucrose-based precursor onto the silicon inverse opals in an attempt to further increase conductivity and achieve mechanical stabilisation of the structures. The amount of carbon deposited proved to be insufficient to stabilise the structures, and silicon-carbon composites demonstrated unsatisfactory electrochemical behaviour. Carbon inverse opals were coated with amorphous silicon producing another type of macroporous composites. These electrodes demonstrated significant improvement both in capacity retentions and in rate capabilities. The inner carbon matrix not only increased the material conductivity, but also resulted in lower silicon pulverisation during cycling.

The current study characterizes the mechanical and biodegradation properties of a polycarbonate polyurethane (PU) electrospun nanofiber scaffold intended for use in the growth of a tissue engineered annulus fibrosus (AF) intervertebral disc component. Both the tensile strength and initial modulus of aligned scaffolds were higher than those of random scaffolds and remained unaffected during a 4 week biodegradation study, suggesting a surface-mediated degradation mechanism. The resulting degradation products were non-toxic. Confined compressive mechanical force of 1kPa, was applied at 1Hz to in vitro bovine AF tissue grown on the scaffolds to investigate the influence of mechanical force on AF tissue production, which was found to decrease significantly at 72 hours relative to 24 hours, independent of any effects from mechanical forces. Overall, the consistent rate of PU degradation, along with mechanical properties comparable to those of native AF tissue, and the absence of cytotoxic effects, make this polymer suitable for further investigation for use in tissue-engineering the AF.