Thesis (Ph.D.)--Massachusetts Institute of Technology, Dept. of Aeronautics and Astronautics, 1981. / MICROFICHE COPY AVAILABLE IN ARCHIVES AND AERONAUTICS. / Bibliography: p. 235-239. / by Jere Schenck Meserole, Jr. / Ph.D.

This thesis describes an experimental program covering the development of certain simple combustion chamber modifications to alleviate smoke emissions from the Allison T56 turboprop engines operated by the Royal Australian Air Force. The work includes a literature survey, smoke emission tests on two variants of the T56 engine, flow visualisation studies of the combustion system in a water tunnel and combustion rig tests of a standard combustor and four possible modifications. The rig tests showed that reductions in smoke emissions of 80% were possible by simple modifications that reduced the primary zone equivalence ratio and improved mixing in that zone.

Combustor blowout is a very serious concern in modern land-based and aircraft engine combustors. The ability to sense blowout precursors can provide significant payoffs in engine reliability and life. The objective of this work is to characterize the blowout phenomenon and develop a sensing methodology which can detect and assess the proximity of a combustor to blowout by monitoring its acoustic signature, thus providing early warning before the actual blowout of the combustor. The first part of the work examines the blowout phenomenon in a piloted jet burner. As blowout was approached, the flame detached from one side of the burner and showed increased flame tip fluctuations, resulting in an increase in low frequency acoustics. Work was then focused on swirling combustion systems. Close to blowout, localized extinction/re-ignition events were observed, which manifested as bursts in the acoustic signal. These events increased in number and duration as the combustor approached blowout, resulting an increase in low frequency acoustics. A variety of spectral, wavelet and thresholding based approaches were developed to detect precursors to blowout. The third part of the study focused on a bluff body burner. It characterized the underlying flame dynamics near blowout in greater detail and related it to the observed acoustic emissions. Vorticity was found to play a significant role in the flame dynamics. The flame passed through two distinct stages prior to blowout. The first was associated with momentary strain levels that exceed the flames extinction strain rate, leading to flame holes. The second was due to large scale alteration of the fluid dynamics in the bluff body wake, leading to violent flapping of the flame front and even larger straining of the flame. This led to low frequency acoustic oscillations, of the order of von Karman vortex shedding. This manifested as an abrupt increase in combustion noise spectra at 40-100 Hz very close to blowout. Finally, work was also done to improve the robustness of lean blowout detection by developing integration techniques that combined data from acoustic and optical sensors.

In the development of modern rotorcraft vehicles, many unique challenges emerge due to the highly coupled nature of individual rotorcraft design disciplines therefore, the use of an integrated product and process development (IPPD) methodology is necessary to drive the design solution. Through the use of parallel design and analysis, this approach achieves the design synthesis of numerous product and process requirements that is essential in ultimately satisfying the customers demands. Over the past twenty years, Georgia Techs Center for Excellence in Rotorcraft Technology (CERT) has continuously focused on refining this IPPD approach within its rotorcraft design course by using the annual American Helicopter Society (AHS) Student Design Competition as the design requirement catalyst. Despite this extensive experience, however, the documentation of this preliminary rotorcraft design approach has become out of date or insufficient in addressing a modern IPPD methodology. In no design discipline is this need for updated documentation more prevalent than in propulsion system design, specifically in the area of gas turbine technology. From an academic perspective, the vast majority of current propulsion system design resources are focused on fixed-wing applications with very limited reference to the use of turboshaft engines. Additionally, most rotorcraft design resources are centered on aerodynamic considerations and largely overlook propulsion system integration. This research effort is aimed at bridging this information gap by developing a preliminary turboshaft engine design methodology that is applicable to a wide range of potential rotorcraft propulsion system design problems. The preliminary engine design process begins by defining the design space through analysis of the initial performance and mission requirements dictated in a given request for proposal (RFP). Engine cycle selection is then completed using tools such as GasTurb and the NASA Engine Performance Program (NEPP) to conduct thorough parametric and engine performance analysis. Basic engine component design considerations are highlighted to facilitate configuration trade studies and to generate more detailed engine performance and geometric data. Throughout this approach, a comprehensive engine design case study is incorporated based on a two-place, turbine training helicopter known as the Georgia Tech Generic Helicopter (GTGH). This example serves as a consistent propulsion system design reference highlighting the level of integration and detail required for each step of the preliminary turboshaft engine design methodology.

Turbulent combustion processes are inherently unsteady and, thus, a source of acoustic radiation, which occurs due to the unsteady expansion of reacting gases. While prior studies have extensively characterized the total sound power radiated by turbulent flames, their spectral characteristics are not well understood. The objective of this research work is to measure the flow and acoustic properties of an open turbulent premixed jet flame and explain the spectral trends of combustion noise. The flame dynamics were characterized using high speed chemiluminescence images of the flame. A model based on the solution of the wave equation with unsteady heat release as the source was developed and was used to relate the measured chemiluminescence fluctuations to its acoustic emission. Acoustic measurements were performed in an anechoic environment for several burner diameters, flow velocities, turbulence intensities, fuels, and equivalence ratios. The acoustic emissions are shown to be characterized by four parameters: peak frequency (Fpeak), low frequency slope (beta), high frequency slope (alpha) and Overall Sound Pressure Level (OASPL). The peak frequency (Fpeak) is characterized by a Strouhal number based on the mean velocity and a flame length. The transfer function between the acoustic spectrum and the spectrum of heat release fluctuations has an f^2 dependence at low frequencies, while it converged to a constant value at high frequencies. Furthermore, the OASPL was found to be characterized by (Fpeak mfH)^2, which resembles the source term in the wave equation.

Gas turbine engines for aircraft applications are required to meet multiple performance and sizing requirements, subject to constraints established by the best available technology level. The performance requirements and limiting values of constraints that are considered by the cycle analyst conducting an engine cycle design occur at multiple operating conditions. The traditional approach to cycle analysis chooses a single design point with which to perform the on-design analysis. Additional requirements and constraints not transpiring at the design point must be evaluated in off-design analysis and therefore do not influence the cycle design. Such an approach makes it difficult to design the cycle to meet more than a few requirements and limits the number of different aerothermodynamic cycle designs that can reasonably be evaluated. Engine manufacturers have developed computational methods to create aerothermodynamic cycles that meet multiple requirements, but such methods are closely held secrets of their design process. This thesis presents a transparent and publicly available on-design cycle analysis method for gas turbine engines which generates aerothermodynamic cycles that simultaneously meet performance requirements and constraints at numerous design points. Such a method provides the cycle analyst the means to control all aspects of the aerothermodynamic cycle and provides the ability to parametrically create candidate engine cycles in greater numbers to comprehensively populate the cycle design space from which a "best" engine can be selected. This thesis develops the multi-design point on-design cycle analysis method labeled simultaneous MDP. The method is divided into three different phases resulting in an 11 step process to generate a cycle design space for a particular application. Through implementation of simultaneous MDP, a comprehensive cycle design space can be created quickly for the most complex of cycle design problems. Furthermore, the process documents the creation of each candidate engine providing transparency as to how each engine cycle was designed to meet all of the requirements. The simultaneous MDP method is demonstrated in this thesis on a high bypass ratio, separate flow turbofan with up to 25 requirements and constraints and 9 design points derived from a notional 300 passenger aircraft.

Thesis (Ph.D.) -- McMaster University, 1998. / Includes bibliographical references (leaves 206-210). Also available via World Wide Web.

Thesis (Ph. D.)--Florida State University, 2005. / Advisor: Dr. Anjaneyulu Krothapalli, Florida State University, College of Engineering, Dept. of Mechanical Engineering. Title and description from dissertation home page (viewed June 14, 2005). Document formatted into pages; contains xx, 224 pages. Includes bibliographical references.

Thesis (M.S.)--Rochester Institute of Technology, 2004. / Typescript. Includes bibliographical references (leaves 65-66).

Thesis (Ph.D)--Aerospace Engineering, Georgia Institute of Technology, 2008. / Committee Chair: Seitzman, Jerry; Committee Member: Filatyev, Sergei; Committee Member: Jagoda, Jechiel; Committee Member: Lieuwen, Timothy; Committee Member: Shelton, Samuel; Committee Member: Zinn, Ben. Part of the SMARTech Electronic Thesis and Dissertation Collection.