The doctoral thesis deals with design of coding for frequency hopping stations in band with intensive jamming. In digital modulations erroneous determination of the modulation state occurs due to jam at the receiver side. The result is erroneously transferred symbols of the message. Errors created during the transmission can be eliminated by using error control systems. It is also possible to prevent these errors by using algorithms (techniques) of frequency hopping which select the appropriate channel. Appropriate communication channel is a channel with a lower probability of erroneous symbol in the message. The main contribution of this thesis is to design a new frequency hopping technique with collision avoidance (FH/CA). The station with FH/CA technique measures signal levels in the considered several channels before every jump. Based on the measurements the most appropriate channel with the lowest value of measured signal level is selected. Therefore, it is more probable that a jump to an unoccupied channel with a transmission will occur. Using a mathematical model, the performance of the newly proposed FH/CA technique is compared with the currently used techniques FH and AFH. Comparison criteria are the probability of a collision between an FH/CA communication system and a static (device transmitting continuously at a fixed frequency) or dynamic jammer (i.e. other FH or AFH systems). By comparing the values of the probability of jammed transmission, indisputable theoretical advantages of the new FH/CA technique were found, compared to the currently used FH and AFH techniques. The FH/CA technique always has better or equal results compared with the FH technique in the case of interference by static and dynamic jammers. The FH/CA technique in a band with static and dynamic jammers usually has better results than the AFH technique. A significant contribution of the FH/CA technique can be seen in the case of dynamic jammers. On the other hand, in the case of static jammers the FH/CA technique is in certain situations worse than the AFH technique. The accuracy of the mathematical models were successfully verified on a simulation model that was created as a part of this thesis in the MATLAB environment. Based on the obtained data from the model there was designed coding for frequency hopping stations with the new technique of frequency hopping FH/CA which is designed for small-volume data transfer in a band with intensive jamming.

Les réseaux de capteurs acoustiques sous-marins (UW-ASN) sont les plus nouveaux achèvements technologiques en termes de communication. Les UW-ASN visent à observer et à explorer les lacs, les rivières, les mers et les océans. Récemment, ils ont été soumis à une attention particulière en raison de leur grand potentiel en termes d'applications prometteuses dans divers domaines (militaires, environnementaux, scientifiques ...) et aux nouvelles questions scientifiques qu'ils suscitent. Un problème majeur dans les UW-ASN est l'épuisement rapide de l'énergie, car une grande puissance est nécessaire pour la communication acoustique, tandis que le budget de la batterie des capteurs est limité. Par conséquent, les protocoles de communication énergétiques revêtent une importance primordiale pour faire usage judiciaire du budget énergétique disponible. Dans ce contexte, cette thèse vise à étudier les principales caractéristiques des capteurs acoustiques sous-marins difficiles afin de concevoir des protocoles de communication énergétiques, plus spécifiquement au niveau routage et MAC. Tout d'abord, nous abordons le problème des trous énergétiques dans UW-ASN. Le problème du « sink-hole » se produit lorsque les capteurs les plus proches du sink épuisent leur énergie plus rapidement en raison de leur charge plus lourde. En effet, ces capteurs, en particulier ceux qui sont à un seul saut du sinkstatique, agissent comme des relais pour tous les autres capteurs, ce qui leur épuise sévèrement l’énergie.A la couche de routage,en particulier, nous proposons de distribuer la charge transmise par chaque capteur parmi plusieurs voisins potentiels, en supposant que les capteurs peuvent ajuster leur gamme de communication entre deux niveaux lorsqu'ils envoient ou transmettent des données. Plus précisément, nous déterminons pour chaque capteur l'ensemble des prochains sauts avec les poids de charge associés qui entraînent un épuisement équitable d'énergie entre tous les capteurs du réseau. Ensuite, nous étendons notre stratégie de routage équilibrée en supposant que chaque capteur n'est pas seulement capable d'ajuster sa puissance d'émission à 2 niveaux mais aussi jusqu'à n niveaux où n> 2. Par conséquent, à la couche de routage, pour chaque valeur possible de n, nous déterminons pour chaque capteur l'ensemble des éventuels sauts avec les poids de charge associés qui mènent à une consommation d'énergie équitable chez tous les capteurs du réseau. En outre, nous obtenons le nombre optimal de puissances de transmission n qui équilibre la consommation d'énergie de tous les capteurs pour chaque configuration de réseau. En plus de cela, il convient de souligner que notre protocole de routage étendu utilise un modèle de canal à variation de temps plus réaliste qui tient compte de la plupart des caractéristiques fondamentales de la propagation acoustique sous-marine. Les résultats analytiques montrent que notre protocole de routage assure une réduction importante de la consommation d’énergie. Deuxièmement, pour atténuer les impacts de collision spectaculaires gaspillant l’énergie, nous concevons un protocole MAC multicanal (MC-UWMAC) évitant les collisions pour les UW-ASNs. MC-UWMAC fonctionne avec un canal de contrôle (décomposé en créneaux de temps) et un ensemble de canaux de données à bande passante égale. Les créneaux du canal de contrôle sont dédiés à l’échange RTS / CTS permettant à une paire de capteurs communicants de s'accorder sur l'heure de début de la communication sur un canal de données pré-alloué. Dans cette thèse, nous proposons deux nouvelles procédures associées d'allocation des créneaux du canal de contrôle et d'attribution des canaux de données sans nécessiter de frais de négociation supplémentaires. En conséquence, chaque capteur peut initier l'échange RTS / CTS uniquement à son créneau assigné, calculé à l'aide d'une procédure d'allocation basée sur une partition virtuelle de grille de la zone de déploiement. (...) / UnderWaterAcoustic Sensor Networks (UW-ASNs) are the newest technological achievement in terms of communication. Composed of a set of communicating underwater sensors, UW-ASNs are intended to observe and explore lakes, rivers, seas and oceans. Recently, they have been subject to a special attention due to their great potential in terms of promising applications in various domains (military, environmental, scientific...) and to the new scientific issues they raise. A great challenging issue in UW-ASNs is the fast energy depletion since high power is needed for acoustic communication while sensors battery budget is limited. Hence, energy-efficient networking protocols are of a paramount importance to make judicious use of the available energy budget while considering the distinguishing underwater environment characteristics. In this context, this thesis aims at studying the main challenging underwater acoustic sensors characteristics to design energy-efficient communication protocols specifically at the routing and MAC layers. First, we address the problem of energy holes in UW-ASNs. The sink-hole problem occurs when the closest nodes to sink drain their energy faster due to their heavier load. Indeed, those sensors especially the ones that are 1-hop away from the static sink act as relays to it on behalf of all other sensors, thus suffering from severe energy depletion. In particular, at the routing layer, we propose to distribute the transmission load at each sensor among several potential neighbors, assuming that sensors can adjust their communication range among two levels when they send or forward data. Specifically, we determine for each sensor the set of next hops with the associated load weights that lead to a fair energy depletion among all sensors in the network. Then, we extend our balanced routing strategy by assuming that each sensor node is not only able to adjust its transmission power to 2 levels but eventually up to n levels where n > 2. Consequently, at the routing layer, for each possible value of n, we determine for each sensor the set of possible next hops with the associated load weights that lead to a fair energy consumption among all sensors in the network. Moreover, we derive the optimal number of transmission powers n that balances the energy consumption among all sensors for each network configuration. In addition to that, it is worth pointing out that our extended routing protocol uses a more realistic time varying channel model that takes into account most of the fundamental characteristics of the underwater acoustic propagation. Analytical results show that further energy saving is achieved by our extended routing scheme. Second, to mitigate the dramatic collision impacts, we design a collision avoidance energy efficient multichannel MAC protocol (MC-UWMAC) for UW-ASNs. MC-UWMAC operates on single slotted control and a set of equal-bandwidth data channels. Control channel slots are dedicated to RTS/CTS handshaking allowing a communicating node pair to agree on the start time of communication on a pre-allocated data channel. In this thesis, we propose two novel coupled slot assignment and data channels allocation procedures without requiring any extra negotiation overhead. Accordingly, each node can initiate RTS/CTS exchange only at its assigned slot calculated using a slot allocation procedure based on a grid virtual partition of the deployment area. Moreover, for each communicating pair of nodes, one data channel is allocated using a channel allocation procedure based on our newly designed concept of singleton- intersecting quorum. Accordingly, each pair of communicating nodes will have at their disposal a unique 2-hop conflict free data channel. Compared with existing MAC protocol, MC-UWMAC reduces experienced collisions and improves network throughput while minimizing energy consumption.

This work presents applications of an ab-initio molecular dynamics method, the so-called nonadiabatic quantum molecular dynamics (NA-QMD), for various molecular systems with many electronic and nuclear degrees of freedom. Thereby, the nuclei will be treated classically and the electrons with time-dependent density functional theory (TD-DFT) in basis expansion. Depending on the actual system and physical process, well suited basis sets for the Kohn-Sham orbitals has to be chosen. For the ionization process a novel absorber acting in the energy space as well as additional basis functions will be used depending on the laser frequency. In the first part of the applications, a large variety of different laser-induced molecular processes will be investigated. This concerns, the orientation dependence of the ionization of multielectronic diatomics (N2, O2), the isomerization of organic molecules (N2H2) and the giant excitation of the breathing mode in fullerenes (C60). In the second part, fullerene-fullerene collisions are investigated, for the first time in the whole range of relevant impact velocities concerning the vibrational and electronic energy transfer (\"stopping~power\"). For low energetic (adiabatic) collisions, it is surprisingly found, that a two-dimensional, phenomenological collision model can reproduce (even quantitatively) the basic features of fusion and scattering observed in the fully microscopic calculations as well as in the experiment. For high energetic (nonadiabatic) collisions, the electronic and vibrational excitation regimes are predicted, leading to multifragmentation up to complete atomization.

Indiana University-Purdue University Indianapolis (IUPUI) / The Pedestrian Automatic Emergency Braking System (PAEB) can utilize on-board sensors to detect pedestrians and take safety related actions. However, PAEB system only benefits the individual vehicle and the pedestrians detected by its PAEB. Additionally, due to the range limitations of PAEB sensors and speed limitations of sensory data processing, PAEB system often cannot detect or do not have sufficient time to respond to a potential crash with pedestrians. For further improving pedestrian safety, we proposed the idea for integrating the complimentary capabilities of V2V and PAEB (V2V-PAEB), which allows the vehicles to share the information of pedestrians detected by PAEB system in the V2V network. So a V2V-PAEB enabled vehicle uses not only its on-board sensors of the PAEB system, but also the received V2V messages from other vehicles to detect potential collisions with pedestrians and make better safety related decisions. In this thesis, we discussed the architecture and the information processing stages of the V2V-PAEB system. In addition, a comprehensive Matlab/Simulink based simulation model of the V2V-PAEB system is also developed in PreScan simulation environment. The simulation result shows that this simulation model works properly and the V2V-PAEB system can improve pedestrian safety significantly.

Technology pervades our daily living, and is increasingly integrated into the vehicle – directly affecting driving. On the one hand technology such as cell phones provoke driver distraction and inattention, whereas, on the other hand, Advanced Driver Assistance Systems (ADAS) support the driver in the driving task. The question is, can a driver successfully adapt to the ever growing technological advancements? Thus, this thesis aimed at improving safe driver behaviour by understanding the underlying psychological mechanisms that influence behavioural change. Previous research on ADAS and human attention was reviewed in the context of driver behavioural adaptation. Empirical data from multiple data sources such as driving performance data, visual behaviour data, video footage, and subjective data were analyzed to evaluate two ADAS (a brake-capacity forward collision warning system, B-FCW, and a Visual Distraction Alert System, VDA-System). Results from a field operational test (EuroFOT) showed that brake-capacity forward collision warnings lead to immediate attention allocation toward the roadway and drivers hit the brake, yet change their initial response later on by directing their eyes toward the warning source in the instrument cluster. A similar phenomenon of drivers changing initial behaviour was found in a driving simulator study assessing a Visual Distraction Alert System. Analysis showed that a Visual Distraction Alert System successfully assists drivers in redirecting attention to the relevant aspects of the driving task and significantly improves driving performance. The effects are discussed with regard to behavioural adaptation, calibration and system acceptance. Based on these findings a novel assessment for human-machine-interaction (HMI) of ADAS was introduced. Based on the contribution of this thesis and previous best-practices, a holistic safety management model on accident prevention strategies (before, during and after driving) was developed. The DO-IT BEST Feedback Model is a comprehensive feedback strategy including driver feedback at various time scales and therefore is expected to provide an added benefit for distraction and inattention prevention. The central contributions of this work are to advance research in the field of traffic psychology in the context of attention allocation strategies, and to improve the ability to design future safety systems with the human factor in focus. The thesis consists of the introduction of the conducted research, six publications in full text and a comprehensive conclusion of the publications. In brief this thesis intends to improve safe driver behaviour by understanding the underlying psychological mechanisms that influence behavioral change, thereby resulting in more attention allocation to the forward roadway, and improved vehicle control.:Abstract i Zusammenfassung iii List of included publications v Acknowledgements vii Previously published work ix Table of contents xi Preface xii 1 Chapter 1 Introduction 1 1.1 Outline 1 1.2 Objectives 2 1.3 Background 8 1.3.1 Behavioural adaption to ADAS 8 1.3.2 Driver distraction and inattention 9 2 Chapter 2 Paper I 23 3 Chapter 3 Paper II 47 4 Chapter 4 Paper III 61 5 Chapter 5 Paper IV 91 6 Chapter 6 Paper V 117 7 Chapter 7 Paper VI 143 8 Chapter 8 Conclusions and discussion 161 8.1. Contributions 161 8.2. Implications 171 8.3. Limitations and research needs 173 9 References 177 Curriculum Vitae 199 Eidesstattliche Erklärung 201 / Technologie durchdringt unser tägliches Leben und ist zunehmend integriert in Fahrzeuge – das Resultat sind veränderte Anforderungen an Fahrzeugführer. Einerseits besteht die Gefahr, dass er durch die Bedienung innovativer Technologien (z.B. Mobiltelefone) unachtsam wird und visuell abgelenkt ist, andererseits kann die Nutzung von Fahrerassistenzsystemen die den Fahrer bei der Fahraufgabe unterstützten einen wertvollen Beitrag zur Fahrsicherheit bieten. Die steigende Aktualität beider Problematiken wirft die Frage auf: "Kann der Fahrer sich erfolgreich dem ständig wachsenden technologischen Fortschritt anpassen?" Das Ziel der vorliegenden Arbeit ist der Erkenntnisgewinn zur Verbesserung des Fahrverhaltens indem der Verhaltensänderungen zugrunde liegende psychologische Mechanismen untersucht werden. Eine Vielzahl an Literatur zu Fahrerassistenzsystemen und Aufmerksamkeitsverteilung wurde vor dem Hintergrund von Verhaltensanpassung der Fahrer recherchiert. Daten mehrerer empirischer Quellen, z. B. Fahrverhalten, Blickbewegungen, Videomitschnitte und subjektive Daten dienten zur Datenauswertung zweier Fahrerassistenzsysteme. Im Rahmen einer Feldstudie zeigte sich, dass Bremskapazitäts-Kollisionswarnungen zur sofortigen visuellen Aufmerksamkeitsverteilung zur Fahrbahn und zum Bremsen führen, Fahrer allerdings ihre Reaktion anpassen indem sie zur Warnanzeige im Kombinationsinstrument schauen. Ein anderes Phänomen der Verhaltensanpassung wurde in einer Fahrsimulatorstudie zur Untersuchung eines Ablenkungswarnsystems, das dabei hilft die Blicke von Autofahrern stets auf die Straße zu lenken, gefunden. Diese Ergebnisse weisen nach, dass solch ein System unterstützt achtsamer zu sein und sicherer zu fahren. Die vorliegenden Befunde wurden im Zusammenhang zu Vorbefunden zur Verhaltensanpassung zu Fahrerassistenzsystemen, Fahrerkalibrierung und Akzeptanz von Technik diskutiert. Basierend auf den gewonnenen Erkenntnissen wurde ein neues Vorgehen zur Untersuchung von Mensch- Maschine-Interaktion eingeführt. Aufbauend auf den Resultaten der vorliegenden Arbeit wurde ein ganzheitliches Modell zur Fahrsicherheit und -management, das DO-IT BEST Feedback Modell, entwickelt. Das Modell bezieht sich auf multitemporale Fahrer-Feedbackstrategien und soll somit einen entscheidenen Beitrag zur Verkehrssicherheit und dem Umgang mit Fahrerunaufmerksamkeit leisten. Die zentralen Beiträge dieser Arbeit sind die Gewinnung neuer Erkenntnisse in den Bereichen der Angewandten Psychologie und der Verkehrspsychologie in den Kontexten der Aufmerksamkeitsverteilung und der Verbesserung der Gestaltung von Fahrerassistenzsystemen fokusierend auf den Bediener. Die Dissertation besteht aus einem Einleitungsteil, drei empirischen Beiträgen sowie drei Buchkapiteln und einer abschliessenden Zusammenfassung.:Abstract i Zusammenfassung iii List of included publications v Acknowledgements vii Previously published work ix Table of contents xi Preface xii 1 Chapter 1 Introduction 1 1.1 Outline 1 1.2 Objectives 2 1.3 Background 8 1.3.1 Behavioural adaption to ADAS 8 1.3.2 Driver distraction and inattention 9 2 Chapter 2 Paper I 23 3 Chapter 3 Paper II 47 4 Chapter 4 Paper III 61 5 Chapter 5 Paper IV 91 6 Chapter 6 Paper V 117 7 Chapter 7 Paper VI 143 8 Chapter 8 Conclusions and discussion 161 8.1. Contributions 161 8.2. Implications 171 8.3. Limitations and research needs 173 9 References 177 Curriculum Vitae 199 Eidesstattliche Erklärung 201

Den Kern der vorliegenden Arbeit bilden sog. sensorgeführte Roboterbewegungen, d. h. die Nutzung von Informationen externer Sensoren zur Regelung des Roboters. Da gängige Industrierobotersysteme üblicherweise positionsgeregelt sind und seitens der Robotersteuerung lediglich der Zugriff zu den Sollwerten der Lageregelkreise erlaubt wird, kann auch der Regelkreis der sensorgeführten Roboterbewegung nur über den Lageregelkreis geschlossen werden. Aus diesem Grunde werden hier nur positionsbasierte Regelungsansätze verfolgt. Die Kraft-/ Momentregelung gilt als eine der wichtigsten Varianten sensorgeführter Roboterbewegungen. Dementsprechend widmet sich auch ein großer Teil dieser Arbeit dem Thema, mit dem Ziel durch innovative und übersichtliche Regelalgorithmen die Akzeptanz der Kraft-/ Momentregelung in industriellen Produktionsprozessen zu erhöhen. Beginnend mit der eindimensionalen Kraftregelung führt der Weg dabei über Konzepte zur Konturenverfolgung und kraft-/ momentgeregelten Montageaufgaben hin zur Kooperation von Robotern. In einem weiteren Teil wird ein Konzept zur Kollisionsvermeidung zwischen Robotern und Hindernissen präsentiert. Es basiert auf dem Ansatz der virtuellen Potential- bzw. Kraftfelder. Dabei ruft das künstliche Feld eine Bewegung des Roboters hervor, die vom Hindernis weg führt. Um das Feld zu erzeugen, wird die Methode der künstlichen Punktladungen entwickelt. Diese werden auf der Oberfläche eines Hindernisses platziert und generieren dann das virtuelle Kraftfeld. Die Platzierung kann z. B. mithilfe der CAD-Daten des Hindernisses erfolgen. Bei bewegten Objekten müssen alle Ladungspositionen ständig aktualisiert werden. Für Lehr- und Präsentationszwecke ist das sog. inverse Pendel eine oft genutzte Regelstrecke. Sein Aufrichten und Stabilisieren ist auch mit Hilfe eines Industrieroboters möglich. Dazu beschäftigt sich ein Kapitel dieser Arbeit mit Fragen zur Modellbildung der Kombination inverses Pendel und Industrieroboter und mit Regelungskonzepten für das Aufschwingen und Balancieren. Letztendlichen wird in diesem Zusammenhang noch ein Visual-Servoing System präsentiert, dass den Neigungswinkel des Pendels mit einer Kamera bestimmt. Alle hier vorgestellten Konzepte und Algorithmen werden Anhand von praktischen Experimenten verifiziert. / This work deals with so-called sensor guided robot motions, which means using the data of external sensors to control the robot. The control loop of the sensor guided robot motion can be only closed around the position control loop, because industrial robot systems usually work position controlled and only access to the desired positions is enabled. For this reason here only position based control approaches are regarded. Force/torque control is a very important type of sensor guided robot motions. According to this, a good portion of this work deals with the subject of force/torque control. Thus, the acceptance of force/torque control in industrial production processes should be increased, by using innovative and clear control algorithms. For this purpose force control in one degree of freedom, contour-following, force/torque controlled assembling tasks and the cooperation between robots are discussed here in different chapters. Thereafter, a concept to collision avoidance between robots and obstacles is presented. It uses the approach of virtual potential/force fields. In this case the artificial field induces a robot motion away from the obstacle. The method of artificial charges is developed to generate this field. For this purpose virtual charges are placed on the surface of the obstacles. Placing of the charges can be performed using e.g. CAD data of the obstacles. Having moving obstacles charge positions must be updated continuously. The inverted pendulum is commonly used teaching students in control theory. The swinging up and the stabilization of the pendulum also can be performed by an industrial robot. One chapter of this work deals with modelling of the robot mounted inverted pendulum and control algorithms for its swinging up and its stabilization. Finally, in combination with the inverted pendulum a visual-servoing system is presented, which measures the pendulum inclination angle by camera. All concepts introduced in this work are verified by practical experiments.

An Automated Guided Vehicle (AGV) must follow protective regulations to avoidcrashing into people when autonomously driving in industries. These safety norms require AGVs to enable protective fields, which perform hard braking when objects enter aspecific area in front of the vehicle. Warning fields, or warning systems, are similar fieldsthat decrease the speed of the AGV before objects enter the protective fields to enable asteadier driving. Today at Toyota Material Handling Manufacturing Sweden (TMHMS),warning systems have been implemented but the systems are too sensitive to objects outside of the AGVs path.The purpose of this thesis is to develop a predictive warning system based on empiricaldata from previous driving scenarios. By storing previous positions, the warning systemcould estimate a trajectory based on simple statistics and deploy speed limiting decisionsif objects appear in the upcoming predicted path.The predictive warning system was compared to the current warning system and adeactivated warning system setup in driving performance and driving dynamics. Performance was measured by measuring time to finish an industry-like test track and dynamicswas subjectively rated from a group of experienced AGV developers from TMHMS. Results showed that a predictive warning system drove the test track faster and with betterdynamics than the current warning system and the no warning system setup.Key findings are that a predictive warning system based on empirical data performedbetter in most cases but has some extra requirements to function. Firstly, the method require the AGV to mostly drive on previously driven paths to produce good results. Secondly the warning system requires a somewhat powerful on board computer to handlethe computations. Finally, the warning system requires spatial awareness of pose for thevehicle, as well as structure and shape for deployed protective fields.

The aim of the project is to design an active safety system forpassenger vehicles for mitigating secondary collisions after an initialimpact. The control objective is to minimize the lateral deviationfrom the known original path while achieving a safe heading angle afterthe initial collision. A hierarchical controller structure is proposed:the higher layer is formulated as a linear time varying model predictivecontroller that denes the virtual control moment input; the lowerlayer deploys a rule-based controller that realizes the requested moment.The designed control system is then tested and validated inSimulink as well as in IPG CarMaker, a high delity vehicle dynamicssimulator. / Syftet med projektet är att för personbilar designa ett aktivtsäkerhetssystem för att undvika följdkollisioner efter en första kollision.Målet är att minimera den laterala avvikelsen från den ursprungligafärdvägen och att samtidigt uppnå en säker kurs efter den första kollisionen.En hierarkisk regulatorstruktur föreslås. Det övre skiktet iregulatorn är formulerat som en linjär tidsvarierande modell prediktivkontroller som definierar den virtuella momentinmatningen. Det nedreskiktet använder en regelbaserad regulator som realiserar det begärdamomentet. Det konstruerade styrsystemet testades och validerades sedani Simulink samt i IPG CarMaker, en simulator med hög precisionför fordonsdynamik.

The goal of nuclear fusion research is to create a clean and virtually limitless energy source. In order to that, a plasma must be heated to hundreds of millions degrees Celsius. A commonly used heating mechanism is ion cyclotron resonance heating, where antennas emit radio waves into the plasma. The wave can resonate with the ions at their cyclotron frequency, which leads to wave absorption. In order to investigate and improve the heating, one can perform computer simulations. FEMIC is a finite element model for ICRH that calculates the wave field created by the antennas. However, this code does not take into account how the wave modifies the velocity distribution of the plasma. Therefore, a time-independent Fokker-Planck solver is implemented that computes the fast ion distribution due to the incident wave field calculated with FEMIC. The novelty of this code is to include Doppler shift, which influences where ions resonate and how they are heated. / Målet med fusionsforskningen är att skapa en ren energikälla som kan producera obegränsade mängder energi. För detta krävs att ett plasma värms till hundratals miljoner grader Celsius. En vanlig teknik för att värma plasmat är joncyklotronuppvärmning, där en antenn emitterar radiovågor som propagerar in i plasmat. Om vågen är i resonans med jonernas cyklotronrörelse leder detta till att vågen absorberas av jonerna. För att studera och utveckla denna uppvärmningsteknik kan man använda datorsimuleringar. FEMIC är en kod baserad på den finita elementmetoden som beräknar vågfälten som skapas av antennen. Med denna kod kan vi dock inte beräkna hur vågen påverkar jonernas fördelningsfunktioner. Därför har en Fokker-Planck-lösare implementerats som kan beräkna fördelningen av snabba joner som accelererats av vågfältet från FEMIC. Det nya i denna modell är att koden tar hänsyn till Dopplerskiftet, vilket påverkar var jonerna är i resonans med vågen och hur de värms upp.

The increasing reliance on space infrastructure and its rapid expansion necessitate the development and enhancement of tools for space debris and fragmentation research. Accurate prediction of the risks associated with satellite fragmentation requires comprehensive understanding of the dynamics involved. To address this need, the widely used NASA Standard Breakup Model (SBM) is employed in this thesis to predict fragment characteristics resulting from breakup events. Additionally, a novel method is introduced to determine the direction of these fragments, something not directly covered by the SBM. Furthermore, the principle of kinetic gas theory is applied to calculate the overall, long-term collision risk between debris and a predetermined satellite population. The results from this reveal the limitations of the SBM in accurately simulating fragmentations for certain satellite types. However, the newly implemented fragment directionality method aligns well with observed data, suggesting its potential for further research. Similarly, the risk model exhibits strong correspondence with ESA's MASTER, a model used for assessing collision risks with debris, with the deviations likely due to different impact velocity models used. Finally, the validated fragmentation and risk models are combined, and the combined model is used to analyse a real-world fragmentation event. / Det ökande beroendet av rymdinfrastruktur, samt dess snabba expansion kräver utveckling och förbättring av verktyg för forskning och analys kring rymdskräp och fragmentering. För att förstå risken förknippad med satellitfragmentationer så krävs förståelse för den involverade dynamiken. För att tillgodose detta används NASA:s Standard Breakup Model (SBM) i denna avhandling för att bestämma fragmentegenskaper som bildas från olika sorters fragmentationshändelser. Dessutom introduceras en ny metod för att bestämma riktningen för dessa fragment, något som inte direkt täcks av SBM. Dessutom tillämpas principen för kinetisk gasteori för att beräkna den totala, långsiktiga kollisionsrisken mellan rymdskrot och en förutbestämd satellitpopulation. Resultaten från detta avslöjar SBM:s begränsningar när det gäller att simulera fragmenten för vissa satellittyper. Hursomhelst så kan man se att den nyligen implementerade fragmentriktningsmetoden stämmer väl överens med den observerade datan, vilket tyder på dess potential för ytterligare forskning. På samma sätt uppvisar riskmodellen överensstämmelse med ESA:s MASTER, en modell som används för att bedöma kollisionsrisker med rymdskrot, där avvikelser sannolikt beror på att olika kollisionshastighetmodeller används. Slutligen kombineras de validerade fragmenterings- och riskmodellerna, som sedan används för att bidra med analyser till en riktig fragmentationshändelse.