Not available / text

Not available / text

Recent findings regarding corrosion of post-tensioned bridges have highlighted the urgent need to develop reliable methods to predict the behavior of the structural system after damage has occurred and inspection techniques to assess the condition of the structure. Corrosion in strands is undesirable in that it often progresses without visual signs of distress, but may cause a brittle failure. To complicate the inspection, access to the strands for visual inspection is usually blocked by the concrete cross section. To date, significant efforts have been taken to improve the durability of the post-tensioned bridges. However, the behavior of the post-tensioned bridges with corrosion damage is not clearly understood and the currently available inspection techniques tend to provide only limited information about the nature and extent of the damage. The research project discussed in this dissertation was developed is to evaluate the feasibility of using the vibration technique to detect and estimate the extent of damage in an external tendon due to corrosion. To accomplish this goal, damage was induced in five specimens, which were monitored periodically to correlate the measured changes in the frequency response to the level of damage. The induced damage simulated the degradation of a post-tensioned structure from corrosion. This dissertation describes the experimental program and the numerical scheme used to estimate the condition of the specimens. Three types of specimens were tested during the experimental phase of the research: individual strands, cables specimens, and external tendons. A series of tension tests of individual strands were conducted to investigate changes in the uniaxial behavior after damage was induced. Simulated damage included uniform corrosion of the strand, mechanical wire cuts, and an initial defect in one wire. Three cable specimens and one tendon specimen were subjected to fatigue loading. The loading was selected to simulate the loss of cross-sectional area in the strands, and also caused grout damage. The frequency response of the specimens was recorded periodically during the fatigue tests and acoustic sensors were used to detect the occurrence of wire breaks. A second tendon specimen was exposed to an acid solution to simulate the hydrogen induced cracking in the strand at three different locations along the length of the specimen. A number of wires fractured during the exposure test and damage was inspected visually. Natural frequencies were also measured periodically. The residual prestressing force in of the specimens was extracted from the measured natural frequencies. The stiff string model was used to determine optimum values of tension and flexural stiffness from the frequency response. The numerical results from this optimization demonstrated the feasibility of using the vibration technique as a nondestructive testing method for external tendons.

published_or_final_version / Civil Engineering / Master / Master of Philosophy

No description available.

The following thesis presents the results of six full scale beams tests as part of a research program conducted at McGill University on the effect of steel fibres on the shear capacity of a beam with an aid ratio greater than 2.5. The test specimens had the following dimensions: 4400 mm long, 300 mm wide and 500 mm long. The beams had 4-25M bottom reinforcing bars and 2-20M top reinforcing bars. Two series were designed with different reinforcing details: the "BA" series contained transverse reinforcement spaced at 275 mm center to center while the "BB" series had no transverse reinforcement. The specimens were cast in three batches of two specimens from each series, with each batch containing concrete with respectively 0%, 0.5% and 1% fibres content by volume. The beams were simply supported and were tested with two equal point loads located at 500 mm from the centre of the beam. / This research project demonstrated a clear improvement of the shear capacity resulting from the use of steel fibres for the beams without transverse reinforcement. For the beams with transverse reinforcement, displacement ductility was highly increased. This suggests that fibres have the potential to reduce the congestion of the reinforcement if fibres are designed to replace partially closely spaced transverse reinforcement. Also, it was noted that a redistribution of stresses occurred resulting in the formation of more well-controlled cracks. Finally, the strength predictions using the method developed by Aoude (Aoude, 2007) agree very well with the experimental results.

One possibility to automate more of software testing is to have developers write more general test cases. Given a general (parameterized test case), that holds in many situations, software can generate many different test instances and execute them automatically. Thus, even though the developers write fewer and smaller tests they can test more. However, it is not clear what other effects the use of generalized test cases has. One hypothesis is that “More general test cases are harder to understand than concrete ones and thus would lead to overall tests that are harder to understand”. Software understandability can be defined as the system that is written by one person is easy to read and understand by another person easily without any resistance. However, software understandability is hard to measure because understandability depends on the cognitive behavior of human. Software understandability assists in software reusability and software maintainability.

M. Phil. / The purpose of this research is to see if on-site portable pull-out tests in South Africa on post-installed chemical and mechanical fixings can produce similar results to internationally laboratory tested fixings. The method used in the field study was to use typical South African 25 MPa, 75 mm slump ready mix concrete as supplied by a reputable supplier and to test several types of fixings in common situations, some covered in the European Technical Approval Guidelines (ETAG) and some not. The results were analyzed against published international values and theoretical calculations for the fixings. The findings showed that the results produced using the portable equipment can show values similar to the published and theoretical values. It was also shown that this methodology can be used as a diagnostic tool to reveal installation errors. The pull-out test operator needs to be skilled to ensure a satisfactory outcome of the tests. The implications of the findings have direct bearing on: The on-site pullout testing of post installed anchors in South Africa; The diagnosing of bad anchor installation. And secondarily bearing on: The education of post-installed fixing installers and designers; The lack of standards for post-installed anchors in South Africa; The transportability of data from international research to South African conditions.

Please read the abstract in the section 00front of this document / Thesis (PhD (Engineering))--University of Pretoria, 2006. / Civil Engineering / unrestricted

Few decades ago, there were no guidelines for torsion design of reinforced concrete (RC) beams. Hence, many existing beams in older buildings have a lack of adequate torsional strength since they were not properly designed for torsion. One way to regain/rehabilitate adequate torsional strength is through application of externally bonded carbon fiber reinforced polymers (CFRP). To date, American Concrete Institute (ACI) code, as well as other building codes, do not have recommendations or provisions for strengthening RC beams for torsion using fiber-reinforced polymer (FRP) composites due to the inexistence of conclusive experimental and analytical data. Of the very limited works on this behavior, the majority of the focus has been devoted to experimental works. Realistic spandrel beams in a building that lack torsional strength were modelled in this research, and strengthened to examine various behaviors such as load capacity, deflection, torque, twist, crack propagation, ductility, and failure modes. For this purpose, six RC beams were tested: four reference beams and two strengthened beams were used to observe additional capacity through the use of carbon fiber-reinforced polymer (CFRP) sheets. To strengthen the beams, one layer of sheets was completely wrapped around them. Results show an additional torsional capacity of 63% and 178% relative to their respective reference beams. Through strengthening, modes of failure of the beams changed from brittle torsion-dominated failure to shear-flexure failure in both beams. The study also included crack pattern and ductility of test beams. Cracks became smaller in width and more evenly distributed across the torsion-loaded area, and torsional ductility was enhanced by 266% and 165% respectively. Flexural ductility was also greatly enhanced by more than five folds. Finally, using ACI 318-14, ACI 440.2R-02, and available formulae in the literature, the beams were analyzed and the respective values were compared.