This diploma thesis deals with acid-base and electrolytic behavior of hyaluronan solutions at different ionic strength. Acid-base behavior of hyaluronan was investigated by acid-base titrations which were carried out with two different methods, acid and alkaline acid-base titration. Dissociation constants at different ionic strength at zero degree of dissociation and at 50% degree of dissociation were evaluated from the results of acid-base titrations. Dissociation constants obtained from acid acid-base titrations have values between 3,0 and 3,6. Dissociation constants obtained from alkaline acid-base titrations are not very informative because their values are much higher than the expected values. The study of degradation of hyaluronan during acid-base titration was performed to complete study of acid-base behavior. Electrolytic behavior of hyaluronan solution was performed by conductometric titrations in three different environments.

Chemical components in wood contain multiple anionic groups, including carboxyl groups and hydroxyl groups. During kraft cooking and bleaching, such structures are also formed, degraded or modified by the action of reactions both deliberate and unwanted. It has previously been found by Laine that anionic groups with pKa values of 3.3 and 5.5 can explain the observed anionic charge on chemical fibres, corresponding to carboxylic acids on hemicelluloses as well as oxidized lignin structures, respectively. It has further been found that most of the fibre charge can be accounted for through the contribution from methylglucuronic acids as well as hexenuronic acids. This study aimed to provide additional information regarding the charge component unaffiliated with either of the aforementioned uronic acids by studying kraft pulps procured from an industrial kraft mill corresponding to unit operations through a fibreline using the ODHot(EOP)D1D2 bleaching sequence. Each sample had its total charge determined by means of conductometric titration, its content of methylglucuronic acid determined by means of methanolysis followed by GC, and its content of hexenuronic acids determined by means of the HUT-method for the determination of hexenuronic acids, followed by either UV absorbance measurements or calculations based on the reduction in kappa number during the selective acid hydrolysis. The lignin content was determined by means of kappa number analysis as well as by calculations based on the kappa number after selective acid hydrolysis, which was assumed to be characteristic of the kappa number addition from the lignin content of the samples. The hexenuronic acid content was successfully determined according to the HUT-method. A difference in content was observed when results for the unbleached and oxygen delignified samples that was obtained from UV measurements were compared with the observed difference in kappa number prior and after selective acid hydrolysis for said samples. In both cases, the results based on the difference in kappa number was higher. No correlation between remaining charge and lignin content could be made. It was instead observed that individual bleaching steps had binary effects on each of the analysed components of the fibre charge. A significant increase in charge unaffiliated with methylglucuronic acid or hexenuronic acid was observed during the EOP step, indicating an oxidation of chemical structures in the pulp: this effect could not be correlated to lignin content. / Kemisk massa kan ses som ett kompositmaterial bestående av cellulosa, hemicellulosa och lignin. Dessa beståndsdelar, liksom separata lågmolekylära föreningar, innehåller anjoniska kemiska grupper som bidrar till att ge träfibrer en anjonisk laddning. Ytterligare sådana grupper kan bildas under reaktioner vid kokning och blekning, tillika kan sådana grupper modifieras eller brytas ner. Laine har tidigare visat att fiberladdningen kan förklaras genom två skilda kategorier av kemiska grupper med pKa värden på 3,3 samt 5,5, vilka kan kopplas till karboxylsyragrupper på hemicellulosor respektive till lignin. Man har därtill funnit att stora delar av fiberladdningen kan förklaras genom tillskott från de två uronsyrorna metylglukuronsyra och hexenuronsyra. Denna studie syftar till att undersöka det laddningstillskott som inte kan länkas till någon av dessa två uronsyror. Detta har gjorts genom att studera kemiska massor från industrin, tagna från de olika stegen i en bleksekvens av typen ODHot(EOP)D1D2. Massornas totalladdning mättes medelst konduktometrisk titrering, emedan metylglukuronsyrahalten mättes via methanolysis följt av GC och hexenuronsyrahalten mättes via selektiv syrahydrolys per HUT-metoden följt av UV-karakterisering respektive beräkningar baserade på differensen i kappa tal före och efter sagda hydrolys. Ligninhalten i samtliga prov mättes via kappatalsmätningar samt genom beräkningar baserade på kappatalet efter selektiv syrahydrolys, vilket anses vara kappatalsbidraget från ligninföreningarna. Hexenuronsyrahalterna uppmätta medelst UV-karakterisering respektive kappatalsdifferens jämfördes mot varandra och fanns ge olika resultat för de oblekta och syrgasdelignifierade massorna. I bägge fallen gav mätningen baserade på kappatalsdifferens högre utslag. Ingen korrelation mellan kvarvarande laddning - totalladdning minus tillskottet från uronsyrorna - och ligninhalt kunde observeras. Istället observerades binära effekter för varje uppmätt komponent under vardera blekningssteg. Under EOP-steget observerades ett tillskott till den kvarvarande laddningen, vilket skulle kunna förklaras genom oxidation av trästrukturer. Dock kan ej heller detta relateras till ligninhalten i proverna.

A presente dissertação trata da implementação e otimização de um sistema de detecção condutométrica sem contato capacitivamente acoplada (C4D) para Eletroforese Capilar (CE). O sistema é caracterizado pela compactação do sistema de detecção, versatilidade e flexibilidade de instalação em diferentes equipamentos comerciais de eletroforese capilar e home made. Desde a década de 80, a eletroforese capilar vem se consolidando como uma das técnicas de separação mais relevantes. Normalmente, os instrumentos comerciais são disponibilizados com detectores ópticos e detectores eletroquímicos. A C4D é utilizada em eletroforese capilar posicionando-se dois eletrodos tubulares envoltos ao capilar. A aplicação de sinais de alta frequência entre os eletrodos permite monitorar variações de condutividade da solução dentro do capilar. Assim, a resposta do detector depende de diversos fatores como mobilidade do analito, do co-íon do eletrólito, da frequência e amplitude do sinal aplicado entre os eletrodos e da geometria dos mesmos. A ausência de componentes móveis torna o presente detector compacto (6,5 cm3) e robusto. O presente C4D é constituído de um oscilador local funcionando a 1,1 MHz, um circuito capaz de converter corrente em tensão, retificar e filtrar os sinais analógcos, além de apresentar um conversor de sinais analógicos em digitais (Conversor A/D) de alta resolução (21 bits efetivos). Outra vantagem é a possibilidade de determinar o diâmetro interno do capilar através da leitura do conversor A/D quando se faz passar um fluxo de ar e, posteriormente água através do capilar. A diferença de leitura de conversor A/D pode ser convertida em diâmetro interno mediante uma curva de calibração. Em uma aplicação típica, os limites de detecção baseado no critério 3s (sem filtragem inicial) foi de 0,6, 0,4, 0,3, 0,5, 0,6 e 0,8 µmol L-1 para K+, Ba2+, Ca2+, Na+, Mg2+ e Li+, respectivamente, é comparável a outras implementações de alta qualidade de um detector condutométrico sem contato capacitivamente acoplado. / This dissertation deals with the implementation and optimization of a Capacitively Coupled Contactless Conductivity Detector (C4D) applied to capillary electrophoresis (CE). The system is characterized by compaction of the detection system, installation flexibility and versatility in different commercial capillary electrophoresis equipment and home-made. Since the 80s, capillary electrophoresis has been consolidated as one of the most important separation techniques. Typically, commercial instruments are available to optical detectors and electrochemical detectors. The C4D is used in capillary electrophoresis positioning two electrodes encased in tubular capillary. The application of high frequency signals between the electrodes allows monitoring changes in conductivity of the solution within the capillary. Thus, the detector response depends on several factors such as mobility of the analyte, the co-ion electrolyte, the frequency and amplitude of the signal applied between the electrodes and the geometry of the same. The absence of moving parts makes this compact detector (6.5 cm3) and robust. This C4D is composed of a local oscillator, working at 1.1 MHz, a circuit capable of converting current into voltage, rectify and filter the analogs signals, besides presenting a high-resolution analog-to-digital converter (ADC) (21 bits effective). Another advantage is the possibility of determining the internal diameter of the capillary by reading the ADC when it is passed a stream of air and then water through the capillary. A readings different ADC can be converted into inner diameter through a curve a calibration curve. In a typical application, the detection limits based on the 3s criterion (without baseline filtering) was 0.6, 0.4, 0.3, 0.5, 0.6 and 0.8 µmol L-1 for K+, Ba2 +, Ca2 +, Na+, Mg2+ and Li+, respectively, is comparable to other high-quality implementations of a capacitively coupled contactless conductivity detector.

A presente dissertação trata da implementação e otimização de um sistema de detecção condutométrica sem contato capacitivamente acoplada (C4D) para Eletroforese Capilar (CE). O sistema é caracterizado pela compactação do sistema de detecção, versatilidade e flexibilidade de instalação em diferentes equipamentos comerciais de eletroforese capilar e home made. Desde a década de 80, a eletroforese capilar vem se consolidando como uma das técnicas de separação mais relevantes. Normalmente, os instrumentos comerciais são disponibilizados com detectores ópticos e detectores eletroquímicos. A C4D é utilizada em eletroforese capilar posicionando-se dois eletrodos tubulares envoltos ao capilar. A aplicação de sinais de alta frequência entre os eletrodos permite monitorar variações de condutividade da solução dentro do capilar. Assim, a resposta do detector depende de diversos fatores como mobilidade do analito, do co-íon do eletrólito, da frequência e amplitude do sinal aplicado entre os eletrodos e da geometria dos mesmos. A ausência de componentes móveis torna o presente detector compacto (6,5 cm3) e robusto. O presente C4D é constituído de um oscilador local funcionando a 1,1 MHz, um circuito capaz de converter corrente em tensão, retificar e filtrar os sinais analógcos, além de apresentar um conversor de sinais analógicos em digitais (Conversor A/D) de alta resolução (21 bits efetivos). Outra vantagem é a possibilidade de determinar o diâmetro interno do capilar através da leitura do conversor A/D quando se faz passar um fluxo de ar e, posteriormente água através do capilar. A diferença de leitura de conversor A/D pode ser convertida em diâmetro interno mediante uma curva de calibração. Em uma aplicação típica, os limites de detecção baseado no critério 3s (sem filtragem inicial) foi de 0,6, 0,4, 0,3, 0,5, 0,6 e 0,8 µmol L-1 para K+, Ba2+, Ca2+, Na+, Mg2+ e Li+, respectivamente, é comparável a outras implementações de alta qualidade de um detector condutométrico sem contato capacitivamente acoplado. / This dissertation deals with the implementation and optimization of a Capacitively Coupled Contactless Conductivity Detector (C4D) applied to capillary electrophoresis (CE). The system is characterized by compaction of the detection system, installation flexibility and versatility in different commercial capillary electrophoresis equipment and home-made. Since the 80s, capillary electrophoresis has been consolidated as one of the most important separation techniques. Typically, commercial instruments are available to optical detectors and electrochemical detectors. The C4D is used in capillary electrophoresis positioning two electrodes encased in tubular capillary. The application of high frequency signals between the electrodes allows monitoring changes in conductivity of the solution within the capillary. Thus, the detector response depends on several factors such as mobility of the analyte, the co-ion electrolyte, the frequency and amplitude of the signal applied between the electrodes and the geometry of the same. The absence of moving parts makes this compact detector (6.5 cm3) and robust. This C4D is composed of a local oscillator, working at 1.1 MHz, a circuit capable of converting current into voltage, rectify and filter the analogs signals, besides presenting a high-resolution analog-to-digital converter (ADC) (21 bits effective). Another advantage is the possibility of determining the internal diameter of the capillary by reading the ADC when it is passed a stream of air and then water through the capillary. A readings different ADC can be converted into inner diameter through a curve a calibration curve. In a typical application, the detection limits based on the 3s criterion (without baseline filtering) was 0.6, 0.4, 0.3, 0.5, 0.6 and 0.8 µmol L-1 for K+, Ba2 +, Ca2 +, Na+, Mg2+ and Li+, respectively, is comparable to other high-quality implementations of a capacitively coupled contactless conductivity detector.