Made available in DSpace on 2014-06-11T19:25:30Z (GMT). No. of bitstreams: 0 Previous issue date: 2010-02-08Bitstream added on 2014-06-13T20:14:00Z : No. of bitstreams: 1 santos_alr_me_guara.pdf: 967831 bytes, checksum: 8cbbf37b87afd6e4a7c7ecc3380f9ebf (MD5) / Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP) / Materiais poliméricos têm sido amplamente utilizados em várias áreas tecnológicas e biomédicas, devido às suas excelentes propriedades mecânicas, térmicas e elétricas. No entanto, estes materiais têm baixa energia de superfície e, portanto, não aderem facilmente a outros materiais. Por isso, para muitas aplicações é necessário modificar a superfície do polímero, a fim de aumentar a sua energia de superfície. Tratamentos a plasma à pressão atmosférica têm sido muito utilizados para modificar as propriedades superficiais de polímeros comerciais, devido aos baixos custos do processo. Este trabalho apresenta os resultados do tratamento de tereftalato de polietileno (PET), poliuretano (PU) e de politetrafluoretileno (PTFE) em plasma de descargas com barreira dielétrica (DBD) em ar, nitrogênio e argônio, à pressão atmosférica. As superfícies tratadas foram caracterizadas por medidas de ângulo de contato, espectroscopia de fotoelétrons de raios-X (XPS) e microscopia de força atômica (AFM). A superfície polimérica, modificada nas DBD a pressão atmosférica, mostraram uma redução significativa no ângulo de contato da água, embora uma recuperação parcial da molhabilidade ocorresse nos primeiros dias após o tratamento. Todavia, a recuperação foi insuficiente para que as amostras tratadas recuperassem a sua molhabilidade original. Análises de XPS mostraram um aumento na concentração de oxigênio na superfície, devido à formação de grupos polares, tais como C-O e OC= O. Um pequeno aumento na concentração de nitrogênio também foi observada. Imagens de AFM mostraram um aumento da rugosidade de polímeros tratados, decorrentes da interação física entre as espécies geradas na descarga e a superfície do polímero. A superfície ativada e a elevada tensão superficial dos polímeros tratados devem levar a um aumento da aderência do polímero. / Polymeric materials have been widely used in various biomedical and technological applications, due to their excellent mechanical, thermal and electric properties. However, these materials have low surface energy, and thus not easily adhere to other materials. Therefore, for many applications it is necessary to modify the polymer surface in order to increase its surface energy. Plasma treatments at atmospheric pressure have been frequently used to modify the surface properties of commercial polymers, due to their low process costs. This work reports the results of polyethylene terephthalate (PET), polyurethane (PU) and polytetrafluoroethylene (PTFE) treatments in plasma by dielectric barrier discharges (DBDs) in air, nitrogen and argon at atmospheric pressure. The plasma-modified surfaces were characterized by contact angle measurements, X-ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM). The polymer surface, modified by DBD at atmospheric pressure, showed a significant decrease in water contact angle although a partial recovery of the surface wettability occurred during the first few days after the treatment. However, the process of hydrophobic recovery was insufficient for complete recovering of the samples original wettability. XPS analysis showed an increase of the oxygen concentration on the surface, due to the formation of polar groups, such as C-O and OC= O. A small increase in the concentration of nitrogen was also observed. AFM images exhibit an increased roughness of the treated polymers because of the physical interaction between the species generated in the discharge and the polymer surface. The activated surface and high surface tension of treated polymers should promote an enhancement of the polymer adhesion to paints and coatings.

This Master Thesis work cover the simulation of the movement of charged species exposed to a high gradient electric field, the same environment a plasma actuator produces. The final goal is to use the plasma actuator as an active flow control device to decrease the drag of a body moving in air. This report describes how the problem was set up in COMSOL Multiphysics and the resulting volume force achieved. The volume force is the force generated by the plasma actuator that is acting on the air. To understand the effect of a plasma actuator better experimental work was also performed. The experimental work include what effect a plasma actuator has on a wing that has stalled out and measuring the air velocity obtained from a single plasma actuator. The conclusion is that more work has to be performed to make the plasma actuator a more effective flow control device. This type of work is a way to understand how plasma actuators work and in extension will lead to how a plasma actuator will be used effectively. / Detta examensarbete behandlar simuleringen om hur laddade partiklar rör sig när de utsätts för ett elektriskt fält med hög gradient, ett liknande närområde som skapas av en plasma aktuator. Slutmålet är att kunna använda plasma aktuatorer som en aktiv flödeskontroll med avsikt att minimera motsåndet på en stelkropp som rör sig genom luften. Den här rapporten beskriver hur problemet ställs upp i COMSOL Multiphysics och vilken volymkraft som fås utav simulerignen. Volymkraften är den genererade kraft från plasma aktuatorn som aggerar på den omgivande luften. Utöver simuleringen har praktiska experiment gjorts för att förstå effekten från en plasma aktuator bättre. Dessa experiment består av hur en plasma aktuator förändrar luftströmmen över en vinge som redan tappat sin lyftkraft och av att mäta vilken hastighet luften kan nå på grund av en plasma aktuator. Sammanfattnignen är att mer arbete behöver göras för att effektivisera en plasma aktuator om den ska användas för flödeskontrol. Detta arbeta är ett steg i att förstå hur plasma aktuatorer fungerar vilket i förlängningen kommer leda till hur man ska använda en plasma aktuator på bästa sätt.

Plasma actuators are electrical devices that generate a wall bounded jet without the use of any moving parts. For aerodynamic applications they can be used as flow control devices to delay separation and augment lift on a wing. The aim of this project is to initially develop a system capable of generating and sustaining a plasma that generates a wall bounded jet. The next step is to investigate the effect of varying the number and distribution of encapsulated electrodes in the dielectric layer. Finally the best case design is applied at the leading edge and flap shoulder of a NACA0015 aerofoil with a 20% flap. Utilising a transformer cascade, plasma has been generated for a variety of input voltages. In the quiescent environment of a Faraday cage the velocity flow field is recorded using particle image velocimetry (PIV). Through understanding of the mechanisms involved in producing the wall jet and the importance of the encapsulated electrode a novel actuator design was investigated. The actuator design distributes the encapsulated electrode throughout the dielectric layer. The experiments have shown that actuators with shallow initial encapsulated electrodes induce velocities greater than the baseline case at the same voltage. Actuators with a deep initial electrode are able to induce the highest velocities as they can operate at higher voltages without breakdown of the dielectric. The best actuator case is applied to the aerofoil for Reynolds numbers of 1:97x10⁵, 2:63x10⁵ and 3:29x10⁵. The lift and drag are recorded using pressure measurements around the aerofoil surface and across the aerofoil's wake. PIV is utilised to visualise the flow field. The trailing edge actuator produces a step increase in lift for pre-stall angles of attack and delays stall by 1° at Re = 1:97x10⁵. The leading edge actuator has limited impact on the flow for the no flap deflection case due to the actuator location. As the flap deflection increases the leading edge actuator is able to influence the flow. Repositioning of the leading edge actuator has the ability to reattach the flow around the fore portion of the aerofoil at a post stall angle of alpha = 18°.

>Magister Scientiae - MSc / In South Africa, water pollution problems have continued to increase due to increasing anthropogenic activities. The increasing number of organic contaminants in various water sources can be attributed to industrial development, population growth and agricultural run- off. These activities have impacted negatively on the availability and accessibility to sustainable clean water resources, exposing citizens to water borne diseases such as cholera, diarrhoea and typhoid fever; commonly reported among children. Advanced oxidation technologies such as dielectric barrier electrohydraulic discharge (EHD), also referred to as dielectric barrier discharge (DBD), have the ability to decompose persistent organics and eliminate microbes. DBD offers advantages such as efficiency, energy saving, rapid processing, use of few or no chemicals, and non-destructive impact on the ecosystem. The system is also capable of generating ozone, hydrogen peroxide, singlet oxygen, superoxide radicals, hydroxyl radicals and other active species. The combination of these reactive species has been reported to degrade biological and chemical pollutants rapidly and efficiently. In this study, the DBD system was optimized by investigating the effect of physico-chemical, electrical parameters and reactor configurations on Methylene Blue (MB) decolouration efficiency. The physico-chemical parameters included MB concentration, solution pH and conductivity, solution volume, NaCl electrolyte concentration in the electrode compartment and air flow rate. As for electrical parameters, the effects of voltage, electrode type and size on MB decolouration efficiency were studied. The effect of the aforementioned parameters on MB decolouration efficiency was assessed by varying one parameter at a time. The following physico-chemical parameters: time (from 0 - 60 minutes), pH (2.5 - 10.5), solution conductivity (5 - 20 mS/cm), MB concentration (0.5 – 10 mg/L), solution volume (500 – 2000 mL), NaCl electrode electrolyte concentration (10 – 50 g/L) and air flow rate (2– 4 L/min) were varied in their respective ranges under the applied experimental conditions: reactor air gap 2 mm, solution volume 1500 mL, NaCl electrolyte concentration of 50 g/L in the electrode compartment, voltage 25 V (7.8 kV), airflow rate 3 L/min, 0.5 mm silver electrode and a running time of 60 minutes. As for electrical parameters, voltage (from 20 - 25 V), electrode type (copper, silver and stainless steel) and electrode diameter (0.5 – 1.5 mm) were also altered individually at the applied experimental conditions. The reactor air gap was varied from 2 to 6 mm. At the same experimental conditions, the free reactive species generated mainly H2O2 and O3, were detected and quantified using the Eisenberg and indigo methods, respectively. The optimum physico-chemical parameters were found to be MB concentration 5 mg/L, concentration of NaCl electrolyte used in the central compartment of the DBD reactor 50 g/L, solution pH 2.5, solution conductivity 10 mS/cm, air flow rate 3 L/min, solution volume 1500 mL and an optimum contact time of 30 minutes. The optimum electrical parameters were found to be: applied voltage 25 and 1.5 mm silver electrode. The following parameters MB concentration, solution conductivity and pH, applied voltage and reactor configuration significantly affected MB decolouration efficiency compared to parameters such as solution volume, the inlet air flow rate, electrode type and size and NaCl electrolyte concentration in the electrode compartment, which were less effective in enhancing MB decolouration. Moreover, for all DBD experiments performed at the applied experimental conditions, complete decolouration of MB was achieved in the first 30 minutes. However, trends between the optimized parameters and MB decolouration efficiency were mostly observed after 10 minutes. The optimized DBD system reduced the treatment time from 30 to 20 minutes without any chemical additives. Moreover, at 5 mg/L MB under the applied optimum conditions, it was proved that besides 99% of MB decolouration reached after 60 minutes, 53% of total organic carbon (TOC) removal was also achieved. The chemical oxygen demand (COD) characterizing MB toxicity was less than 5 mg/L before as well as after the DBD experiment. After 10 minutes of experiment under the following conditions: Applied voltage 25 V, MB concentration 5 mg/L, solution pH (in between 6.04 and 6.64), solution volume 1500 mL, air flow rate 3 L/min, 0.5 mm silver electrode and a contact time of 60 minutes, about 3.73 x 10-5 mol/L H2O2 was produced which decreased to 2.93 x 10-5 mol/L 10 minutes later, while O3 concentration was initially very low and could not be detected. However, 0.5 mol/L of O3 was detected after 20 minutes of operating time, thereafter, H2O2 concentration decreased continuously with time while that of O3 fluctuated as the treatment time increased. Likewise, the energy density for the production of free reactive species reached 0.87 g/ kWh in the first 10 minutes due to the presence of chromophoric functional groups such as =N+(CH3)2 in MB structure that had to be destroyed. Thereafter, the energy consumption decreased progressively to zero with an increase in treatment time due to the destruction of =N+(CH3)2 groups in MB structure with time. The correlation between the rise in the of H2O2 concentration and energy density after 10 minutes was probably due to dissociation of OH- OH bonds in H2O2 by UV light to yield OH radicals which unselectively may have attacked MB dye. Thus, MB decomposition in the current DBD reactor was mostly initiated by H2O2 and O3. The irradiation of H2O2 by UV light generated in the DBD system was found to accelerate dye decomposition in the first 30 minutes of the experiment. The UV-vis analysis of treated MB samples confirmed that the complete decolouration of MB achieved in the first 30 minutes was due to the destruction of the chromophoric [=N+(CH3)2] group in Methylene blue structure, while the FT-IR confirmed the presence of traces of various functional groups such as C=C, C=O, C=N, NH, NH3, NO2, etc. characteristics of carboxylic acids, amines, amides, nitrogen based compounds (salts), aliphatic and unsaturated by-products remaining in the bulk solution after treatment. The salts analysis after treatment showed that 16 mg/L of nitrates and nitrites and 1.1mg/L of sulphates mainly originating from air and MB decomposition were present in the treated samples. The EHD/DBD system used in this study offers an approach to partially treat water/wastewaters and its optimization was able to significantly enhance the decomposition of the target MB dye as indicated by the reduction of total organic carbon (TOC) from 8.3 mg/L to 3.9 mg/L. Compared to previous research, this study successfully optimised a complete double cylindrical dielectric barrier discharge (DBD) reactor at ambient condition without any chemical additives.

Background: Bacterial contamination of surfaces with methicillin-resistant Staphylococcus aureus (MRSA) is a serious problem in the hospital environment and is responsible for significant nosocomial infections. The pathogenic contaminants form biofilms, which are difficult to treat with routine biocides. Thus, a continuous search for novel disinfection methods is essential for effective infection control measures. This demonstration of a novel technique for the control of virulent pathogens in planktonic form as well as in established biofilms may provide a progressive alternative to standard methodology. Methods: We evaluated a novel technique of normal atmospheric nonthermal plasma known as floating-electrode dielectric-barrier discharge (FE-DBD) plasma against a control of planktonic and biofilm forms of Escherichia coli, S aureus, multidrug-resistant methicillin-resistant S aureus (MRSA) -95 (clinical isolate), -USA300, and -USA400, using widely accepted techniques such as colony count assay, LIVE/DEAD BacLight Bacterial Viability assay, and XTT (2,3-Bis(2-methoxy-4-nitro-5-sulfophenyl)-2H-tetrazolium-5-carboxanilide) assay. Results: Exposure of free living planktonic forms of E coli, S aureus, and MRSA were rapidly inactivated by DBD plasma. Approximately 107 bacterial cells were completely (100%) killed, whereas 108 and 109 were reduced by approximately 90% to 95% and 40% to 45%, respectively, in less than 60 seconds (7.8 J/cm2) and completely disinfected in ≤120 seconds. In established biofilms, the susceptibility of MRSA USA400 was comparable with USA300 but less susceptible than MRSA95 (clinical isolate), S aureus, and E coli (P < .05) to FE-DBD plasma, and plasma was able to kill MRSA more than 60% within 15 seconds (1.95 J/cm2). The killing responses were plasma exposure-time dependent, and cell density dependent. The plasma was able disinfect surfaces in a less than 120 seconds. Conclusion: Application of DBD plasma can be a valuable decontamination technique for the removal of planktonic and biofilm-embedded bacteria such as MRSA -USA 300, -USA 400, methicillin-sensitive S aureus (MSSA), and E coli, the more common hospital contaminants. Of interest, E coli was more resistant than S aureus phenotypes.

The aim of this dissertation is to get to know metodology and construction of suitable electrical insertion in measurement of energy consumed by discharge. These findings will serve to scale dependings of output to frequence for surface and voluminous dielektric barrier discharge in synthetic dry air and determination of effect of humidity in air on electric characteristics of discharge.

Dielectric Barrier Discharge (DBD) excimer lamp is a very attractive source for Ultraviolet (UV) radiation. It has a number of advantages compared to the mercury lamp which is the main lamp used in the industry for UV production. Some of these advantages are instant UV radiation (no warm-up period), narrow UV spectrum, longer life times and simple construction. The DBD UV lamp can be used in number of applications like water disinfection, Plasma Display Panels (PDP) and surface treatment in the semiconductor industry. Yet, the full industrial application of this lamp still faces some problems mainly related to finding the optimum electrical driver to maximize the efficiency of such a lamp. This includes the type of the electrical waveform to generate and the power electronic driver to produce it. In this thesis, firstly a physically based circuit model for the DBD lamp using the Finite Volume Method (FVM) is developed. This model provides the electrical and optical characteristics of the lamp. Using this model the sensitivity of the lamp efficiency to the proposed electrical waveform has been determined. Secondly, the order of this FVM model has been reduced to obtain a model which is used in the design procedure of the proposed driver. Since the DBD lamp has a capacitive nature, a current controlled driver is proposed in this thesis as opposed to most of the published drivers which are voltage controlled drivers. The design of this driver is intended to enhance the electrical to optical efficiency of the lamp and therefore enhancing the overall efficiency of the system. The driver topology permits direct control of the peak lamp current and the operating frequency of the supplied current to the DBD lamp. The width of the current pulses is determined by the transformer magnetizing inductance and the lamp capacitance. Experimental results of the proposed driver connected to a XeCl DBD lamp are presented to validate the performance of the driver and to prove the concept of such a current controlled driver. The proposed driver performance is compared to a voltage source driver which was also implemented. The proposed driver produced higher overall system efficiency but at the expense of a reduction in the driver efficiency as compared to the voltage source driver. The complete system, which consists of the developed FVM based model and the equivalent circuit of the proposed driver, was simulated and the results were compared to the experimental results to validate the accuracy of the developed model for the DBD lamp.

Qualitative and quantitative analysis of trace substances determined by Mass spectrometry has unique advantages which can¡¦t be replaced. For example, the detection limit of common gas sensors are difficult to lower than 1 ppm, and the sensitivity, selectivity, period of use and stability are not ideal. The detection limit of mass spectrometer is general low to 0.01 ppm. Furthermore, all substances in the sample can be simultaneous analysis by mass spectrometer, but single gas sensor measurements cannot. In this study, dielectric barrier discharge plasma is used in environmental mass spectrometry analysis. This study develops an innovative balanced T-shaped dielectric barrier discharge (DBD) plasma generator for generating atmospheric plasma to replace the linear type plasma generator. Through the change of the geometric configuration and the drive phase develop T-shaped dielectric barrier discharge plasma, the balanced design can fully cancel the high potential and noise. The main objective of this study for the more traditional linear electrodes of the study's original novel T-shaped electrodes of different, including mass spectrometry, spectroscopy, and some basic electrical measurements, and by changing the electrode design, voltage, temperature, gas flow, gas flow rate, diameter and other parameters of the dielectric, and compare their differences and to explore the most suitable parameters. The results showed that T-shaped design of the research and development of innovation through the elimination of the exit pressure put EFI flame can indeed significantly reduce sample oxidation and generate fragments of the situation, and thus improve the mass spectrum of readability and debris interference, thus improving the detection limit , especially for some with a benzene ring and long-chain carbon samples. The experimental results confirm that the development of the Institute of Atmospheric Pressure Plasma free system can be prolonged to produce high concentrations of plasma gas as a free source of the mass spectrometry system, and provides more than 107 cm-3 ion concentration. MS-free analysis of the system can be directly on the gas, liquid and solid samples, the test do not need complicated traditional mass spectrometry analysis of the required sample pre-treatment steps, you can get a clear identification of high mass spectrometry signal. In addition to introducing the basic principles and structure of the atmospheric pressure plasma discharge device, and take advantage of many samples test for the different plasma mass spectrometry free system performance verification.

Τα τελευταία χρόνια, στη βιοϊατρική και στη βιομηχανία η επεξεργασία δειγμάτων με πλάσμα έχει κεντρίσει το ενδιαφέρον, και ειδικότερα στους αντιδραστήρες πλάσματος ατμοσφαιρικής πίεσης. Οι αντιδραστήρες αυτοί αντίθετα από του αντιδραστήρες καινού είναι πιο οικονομικοί στην κατασκευή αλλά και στη λειτουργιά. Το ενδιαφέρον αυξάνεται , λαμβάνοντας υπόψη τη δυνατότητα παράγωγης ψυχρού πλάσματος με μεγάλη δραστικότητα, αποφεύγοντας τα μειονεκτήματα των θερμών ατμοσφαιρικών πλασμάτων. Σκοπός της παρούσας εργασίας είναι η υλοποίηση και η βελτιστοποίηση ενός αντιδραστήρα ατμοσφαιρικού πλάσματος ευγενών αεριών τροφοδοτούμενου από ημιτονοειδή υψηλή τάση ακουστικών συχνοτήτων. Το σύστημα οδηγείται από ημιτονοειδή υψηλή τάση μεταβαλλόμενου πλάτους (0-11 kV από κορυφή σε κορυφή) και συχνότητα (5-20 kHz). Στο πρώτο κεφάλαιο παρουσιάζονται οι γενικές έννοιες για τη δομή και τη λειτουργία των αντιδραστήρων αυτού του είδους. Έμφαση δίνεται στο μηχανισμό διάδοσης του πίδακα και στις εκκενώσεις διηλεκτρικού φράγματος. Στο δεύτερο κεφάλαιο γίνεται εκτενής περιγραφή των επιμέρους τμημάτων που κατασκευαστήκαν προκειμένου να είναι εφικτή η λειτουργία του αντιδραστήρα. Αρχικά γίνεται η περιγραφή των αντιδραστήρων που κατασκευαστήκαν και στη συνεχεία παρουσιάζεται το σύστημα τροφοδοσίας της υψηλής τάσης. Τέλος, γίνεται περιγραφή των διατάξεων χαρακτηρισμού της εκκένωσης οι όποιες αφορούν ηλεκτρικές, οπτικές, φωτογραφικές μετρήσεις καθώς και μετρήσεις θερμοκρασίας. Στο τρίτο κεφάλαιο παρουσιάζονται τα αποτελέσματα που προέκυψαν από τις παραπάνω μετρήσεις καθώς μεταβάλλεται μια από τις παραμέτρους του συστήματος (είδος και ροή αερίου, πλάτος και συχνότητα τάσης) Στο τέταρτο κεφάλαιο γίνεται αξιολόγηση των αποτελεσμάτων και προτείνονται μελλοντικές βελτιώσεις και επεκτάσεις προκειμένου να γίνει το σύστημα πιο λειτουργικό. Η διπλωματική εργασία ολοκληρώνεται με το Παράρτημα στο όποιο δίνονται τα μηχανολογικά σχεδία των αντιδραστήρων. / In recent years plasma processing has spurred interest in biomedical and industrial applications, particularly in atmospheric pressure plasma reactors. These reactors unlike vacuum ones are more economical to build and operate. The interest is growing considering the possibility of generating reactive cold plasmas, avoiding the drawbacks of thermal atmospheric plasmas. The goal of this thesis is the implementation and optimization of an atmospheric pressure plasma reactor fed with noble gases and sinusoidal high voltage audio frequencies. The system is driven by a sinusoidal high voltage with variable amplitude (0-11 kV peak- to-peak) and frequency (5-20 kHz) The first chapter presents the general concepts about the structure and operation of reactors of this kind. Emphasis is given to the propagation mechanism of the jet and dielectric barrier discharges. The second chapter is an extensive description of the components manufactured in order to allow the operation of the reactor. Initially, a detailed description of reactors built is given and then the high voltage supply system is presented. Finally, the instrumentation setup is explained regarding the electrical, optical, photographic and temperature measurements. The third chapter presents the results obtained from these measurements as a changing of system parameters (gas type and flow , voltage amplitude and frequency ) In the fourth chapter we reviewed the results and proposed future improvements and extensions in order to make the system more functional. The thesis concludes with the Annex in which the engineering drawings of the reactors are given

Dielectric Barrier Discharge (DBD) excimer lamp is a very attractive source for Ultraviolet (UV) radiation. It has a number of advantages compared to the mercury lamp which is the main lamp used in the industry for UV production. Some of these advantages are instant UV radiation (no warm-up period), narrow UV spectrum, longer life times and simple construction. The DBD UV lamp can be used in number of applications like water disinfection, Plasma Display Panels (PDP) and surface treatment in the semiconductor industry. Yet, the full industrial application of this lamp still faces some problems mainly related to finding the optimum electrical driver to maximize the efficiency of such a lamp. This includes the type of the electrical waveform to generate and the power electronic driver to produce it. In this thesis, firstly a physically based circuit model for the DBD lamp using the Finite Volume Method (FVM) is developed. This model provides the electrical and optical characteristics of the lamp. Using this model the sensitivity of the lamp efficiency to the proposed electrical waveform has been determined. Secondly, the order of this FVM model has been reduced to obtain a model which is used in the design procedure of the proposed driver. Since the DBD lamp has a capacitive nature, a current controlled driver is proposed in this thesis as opposed to most of the published drivers which are voltage controlled drivers. The design of this driver is intended to enhance the electrical to optical efficiency of the lamp and therefore enhancing the overall efficiency of the system. The driver topology permits direct control of the peak lamp current and the operating frequency of the supplied current to the DBD lamp. The width of the current pulses is determined by the transformer magnetizing inductance and the lamp capacitance. Experimental results of the proposed driver connected to a XeCl DBD lamp are presented to validate the performance of the driver and to prove the concept of such a current controlled driver. The proposed driver performance is compared to a voltage source driver which was also implemented. The proposed driver produced higher overall system efficiency but at the expense of a reduction in the driver efficiency as compared to the voltage source driver. The complete system, which consists of the developed FVM based model and the equivalent circuit of the proposed driver, was simulated and the results were compared to the experimental results to validate the accuracy of the developed model for the DBD lamp.