El conocimiento de las características interfaciales es de suma importancia para poder desarrollar materiales que sean capaces de dar lugar a reacciones electrocatalíticas eficientes. Por esta razón, en esta tesis se muestran diferentes estudios interfaciales sobre superficies monocristalinas de platino y cobre en diferentes electrolitos. Además se estudian las características de la interfase electrodoldisolución con superficies de platino modificadas con adátomos de hierro, cobalto y níquel. Para ello, se han empleado las técnicas de voltametría cíclica, espectroscopía infrarroja con transformada de Fourier, desplazamiento de carga con CO y salto de temperatura inducido por láser. Los resultados muestran cómo varía el campo eléctrico interfacial disminuye al aumentar el recubrimiento de hierro y níquel en la superficie de platino. Este efecto tiene un gran impacto en la reacción de evolución de hidrógeno, ya que la mejora electrocatalítica de esta reacción está relacionada con la energía de reorganización de las moléculas de agua, la cual, depende de la fortaleza del campo eléctrico interfacial. Los estudios realizados en medio alcalino para las diferentes superficies de cobre y platino sin modificar muestran una correlación entre el potencial de máxima entropía y las funciones de trabajo para cada una de las diferentes orientaciones atómicas superficiales. Por otro lado, debido a la aplicabilidad de las nanopartículas en los sistemas reales de conversión de energía, se realizaron experimentos de sincrotrón empleando la técnica de Bragg coherent difraction imaging con el objetivo de estudiar el deterioro de las nanopartículas en condiciones operando.

Kern der vorliegenden Arbeit ist die Anwendung quantenchemischer Methoden auf Probleme der elektrochemischen Katalyse vor dem Hintergrund der Sauerstoffreduktion, wie sie an kohlenstoffgeträgerten Platinkatalysatoren abläuft. In diesem Zusammenhang werden die Stabilität des Katalysatorsystems und der Mechanismus der Sauerstoffreduktion untersucht, sowie ein Algorithmus zur Berechnung von Molekülen unter einem gegebenen Potential vorgestellt. Zuerst werden die Wechselwirkungen von Platinnanopartikeln mit polyzyklischen Aromaten als Modellverbindungen des Katalysatormaterials untersucht. Weiterhin wird untersucht, wie Modifikationen des Kohlenstoffträgers und variierende Größe des Platinsystems diese Wechselwirkungen beeinflussen. Weiterhin beschäftigt sich diese Arbeit mit dem Reaktionsmechanismus der Sauerstoffreduktion. Zu diesem Zweck wird das Zersetzungsverhalten von H2O2 als mögliches Intermediat der Sauerstoffreduktion an Platinoberflächen untersucht. Weiterhin wird geprüft, inwieweit dem Elektrolyten hinzugefügte Ionen die Zersetzungsreaktionen beeinflussen. Abschließend werden Rückschlüsse auf den Reaktionspfad der Sauerstoffreduktion gezogen. Zuletzt wird ein theoretischer Ansatz zur Berechnung von Systemen im Rahmen der Dichtefunktionaltheorie vorgestellt, bei dem nicht die Anzahl der Elektronen, sondern das elektrochemische Potential vorgegeben ist und die Elektronenzahl potentialabhängig modifiziert wird. Ebenso wird die Relevanz von Rechnungen mit konstantem Potential demonstriert.

Die elektrokatalytische Wasserspaltung gilt als die nachhaltigste und sauberste Technologie zur Produktion von H2. Leider wird die Effizienz durch die träge Kinetik der Sauerstoffentwicklungsreaktion (OER) an der Anode stark eingeschränkt. Im Gegensatz zur OER ist die Elektrooxidation organischer Stoffe (EOO) thermodynamisch und kinetisch günstiger. Daher hat sich die Kopplung der EOO mit der Wasserstoffentwicklungsreaktion (HER) als Alternative herauskristallisiert, weil dabei die katalytische Effizienz für die H2-Produktion erheblich verbessert werden kann. Gleichzeitig können hochwertige organische Verbindungen an der Anode durch Verbesserung der Elektrooxidation erzeugt werden. In diesem Kurzaufsatz werden die aktuellsten Fortschritte und Meilensteine, die bereits bei der Kopplung der EOO mit der HER erzielt wurden, vorgestellt. Der Fokus liegt auf dem Design des Anodenkatalysators, dem Verständnis des Reaktionsmechanismus und der Konstruktion des Elektrolyseurs. Darüber hinaus werden Herausforderungen und Perspektiven in Bezug auf die künftige Entwicklung dieser innovativen Technologie aufgezeigt.

No description available.

A highly effective electrocatalyst is the central component of advanced electrochemical energy conversion. Recently, two-dimensional conjugated metal-organic frameworks (2D c-MOFs) have emerged as a class of promising electrocatalysts due to their advantages including 2D layered structure with high in-plane conjugation, intrinsic electrical conductivity, permanent pores, large surface area, chemical stability, and structural diversity. In this review, we summarize the recent advances of 2D c-MOF electrocatalysts for electrochemical energy conversion. Firstly, we introduce the chemical design principles and synthetic strategies of the reported 2D c-MOFs, as well as the functional design for the electrocatalysis. Subsequently, we present the representative 2D c-MOF electrocatalysts in various electrochemical reactions, such as hydrogen/oxygen evolution, and reduction reactions of oxygen, carbon dioxide and nitrogen. We highlight the strategies for the structural design and property tuning of 2D c-MOF electrocatalysts to boost the catalytic performance, and offer our perspectives in regard to the challenges to be overcome.

Lack of energy storage is a key issue in the development of renewable energy sources. Most renewables, especially solar and wind, when used alone, cannot sustain a reliably constant power output over an extended period of time. These sources generally generate variable amounts of power intermittently, therefore, an efficient electrical energy storage (EES) method is required to better temporally balance power generation to power consumption. One of the more promising methods of electrical energy storage is the unitized regenerative fuel cell (UFRC.) UFRCs are fuel cells that can operate in a charge-discharge cycle, similar to a battery, to store and then to subsequently release power. Power is stored by means of electrolysis while the products of this electrolysis reaction can be recombined as in a normal fuel cell to release the stored power. A major advantage of UFRCs over batteries is that storage capacity can be decoupled from cell power, thus reducing the potential cost and weight of the cell unit. Here we investigate UFRCs based on hydrogen-halogen systems, specifically hydrogen-bromine, which has potential for improved electrode reaction kinetics and hence cheaper catalysts and higher efficiency and energy density. A mathematical model has been developed to analyze this system and determine cell behavior and cycle efficiency under various conditions. The conventional H2-Br2 URFCs, however also so far have utilized Pt catalysts and Nafion membranes. Consequently, a goal of this work was to explore alternate schemes and materials for the H2-Br2 URFC. Thus, three generations of test cells have been created. The first two cells were designed to use a molten bromide salt, ionic liquid or anion exchange membrane as the ion exchange electrolyte with the liquids supported on a porous membrane. This type of system provides the potential to reduce the amount of precious metal catalyst required, or possibly eliminate it altogether. Each cell showed improvement over the previous generation, although the results are preliminary. The final set of results are promising for anion exchange membranes on a cost basis compared Nafion. Another promising energy storage solution involves liquid methanol as an intermediate or as a hydrogen carrier. An alternative to storing high-pressure hydrogen is to produce it on-board/on-site on demand via a methanol electrocatalytic reformer (eCRef), a PEM electrolyzer in which methanol-water coelectrolysis takes place. Methanol handling, storage, and transportation is much easier than that for hydrogen. The hydrogen produced via methanol eCref may then be used in any number of applications, including for energy storage and generation in a standard H2-O2 PEM fuel cell. The mathematical modeling and analysis for an eCref is very similar to that of the HBr URFC. In this work, a comprehensive model for the coelectrolysis of methanol and water into hydrogen is created and compared with experimental data. The performance of the methanol electrolyzer coupled with a H2-O2 fuel cell is then compared for efficiency to that of a direct methanol fuel cell data and was found to be superior. The results suggest that an efficient and small paired eCRef-fuel cell system is potentially be a cheaper and more viable alternative to the standard direct methanol fuel cell. Both the H2-Br2 URFC and the methanol eCref in combination with a H2-O2 fuel cell have significant potential to provide higher energy efficiency and energy density for EES purposes.

Les électrocatalyseurs conventionnels utilisés dans les piles à combustibles à membrane échangeuse de protons (PEMFC) sont composés de nanoparticules de platine supportées sur des noirs de carbone de forte surface spécifique. A la cathode de la PEMFC, siège de la réaction de réduction de l’oxygène (ORR), le potentiel électrochimique peut atteindre des valeurs élevées - notamment lors de phases arrêt-démarrage - engendrant des dégradations irréversibles du support carboné. Une solution « matériaux » consiste à remplacer ce dernier par des supports à base d’oxydes métalliques. Ceux-ci doivent être résistants à la corrosion électrochimique, conducteurs électroniques et posséder une structure poreuse et nano-architecturée (permettant le transport des réactifs et produits et une distribution homogène de l’ionomère et des nanoparticules de platine). Dans ce travail, nous avons donc élaboré et caractérisé des électrocatalyseurs à base de nanoparticules de platine (Pt) déposées sur du dioxyde d’étain (SnO₂) et de titane (TiO₂) texturés (morphologies aérogel, nanofibres ou « loosetubes ») et conducteurs électroniques (dopés au niobium Nb ou à l’antimoine Sb). Le support permettant d’atteindre les meilleures propriétés électrocatalytiques est un aérogel de SnO₂ dopé à l’antimoine, noté ATO. En particulier, l’électrocatalyseur Pt/ATO présente une activité spécifique vis-à-vis de l’ORR supérieure à celle d’un électrocatalyseur Pt/carbone Vulcan® synthétisé dans les mêmes conditions, suggérant des interactions bénéfiques entre les nanoparticules de Pt et le support oxyde métallique (Strong Metal Support Interactions, SMSI).Des tests de durabilité simulant le fonctionnement d’une PEMFC en conditions automobile ont été effectués en électrolyte liquide à 80 °C sur ces deux électrocatalyseurs : cyclage entre 0,60 et 1,00 V vs l’électrode réversible à hydrogène (RHE) ou entre 1,00 et 1,50 V vs RHE. Le catalyseur Pt/ATO présente une durabilité accrue par rapport au catalyseur Pt/carbone Vulcan® de référence. Cependant, de nouveaux mécanismes de dégradation ont été mis en évidence dans cette étude : tout d’abord, l’élément dopant Sb est progressivement dissout au cours du vieillissement électrochimique, ce qui implique une perte de conductivité électronique. Cette perte est en partie liée à des incursions à bas potentiel, notamment durant les caractérisations électrochimiques. De plus, entre 5 000 et 10 000 cycles de vieillissement électrochimique (entre 0,60 et 1,00 V vs RHE ou entre 1,00 et 1,50 V vs RHE à 57 °C), le matériau support perd sa structure poreuse et forme un film amorphe peu conducteur. / Conventional electrocatalysts used in proton exchange membrane fuel cells (PEMFC) are composed of platinum nanoparticles supported on high specific surface area carbon blacks. At the cathode side of the PEMFC, where the oxygen reduction reaction (ORR) occurs, the electrochemical potential can reach high values - especially during startup-shutdown operating conditions - resulting in irreversible degradation of the carbon support. A “material” solution consists of replacing the carbon with supports based on metal oxides. The latter have to be resistant to electrochemical corrosion, be electronic conductor and have a porous and nano-architectural structure (for the transport of reagents and products and the homogeneous distribution of the ionomer and platinum nanoparticles).In this work, we have developed and characterized electrocatalysts composed of platinum (Pt) nanoparticles based on tin dioxide (SnO2) and titanium dioxide (TiO2) with optimized textural (aerogel, nanofibres or loosetubes morphologies) and electron-conduction properties (doped with niobium Nb or antimony Sb). The best electrocatalytic properties are reached for an antimony-doped SnO2 aerogel support, denoted ATO. The Pt/ATO electrocatalyst has especially a higher specific activity for the ORR than a Pt/carbon Vulcan® electrocatalyst, synthesized in the same conditions, suggesting beneficial interactions between the Pt nanoparticles and the metal oxide support (Strong Metal Support Interactions SMSI).Durability tests simulating automotive operating conditions of a PEMFC were carried out in liquid electrolyte at 57 °C on these two electrocatalysts by cycling between 0.60 and 1.00 V vs the reversible hydrogen electrode (RHE) or between 1.00 and 1.50 V vs RHE. The Pt/ATO electrocatalyst has an increased stability compared to the reference Pt/carbon Vulcan® electrocatalyst. However, new degradation mechanisms were highlighted in this study: first, the doping element (Sb) is progressively dissolved during electrochemical ageing, which implies a loss of electronic conductivity. This loss is partly due to incursions at low potential, including during electrochemical characterizations. Moreover, between 5,000 and 10,000 cycles of the accelerated stress tests (between 0.60 and 1.00 V vs RHE or between 1.00 and 1.50 V vs RHE at 57 °C), the support loses its porous structure and forms a poorly conductive amorphous film.

Catalysis using nanostructures has been a topic of substantial interest for fundamental studies and for practical applications in energy and environmental sectors. The growing demand for production of energy and in the cleaning of polluting hazardous vehicles/industrial wastes has led to several studies in catalysis. Despite the substantial growth of heterogeneous catalytic technologies in last decade, they are still far from reaching their full potential in terms of efficiency, selectivity as well as durability. It is often difficult to simultaneously tackle all the mentioned issues with single component catalysts. Most of these challenges are being overcome with heterostructures/supported hybrid catalysts by modifying their interfaces. The properties of heterostructures hybrids arises not only from the individual contributions of the individual components but also from strong synergetic effect arising from the interface. Engineering the interfaces provides pathways to promote the catalytic performance and hence has been explored. In this regard, we have focused on the progress in investigating the active interfaces that affect the performance of metal oxide-metal, semiconductor-metal and coupled semiconductor nanocatalyst hybrids. We explored a wide spectrum of their applications in photo catalytic, electrocatalytic as well as gas-phase reactions and highlighted the importance of the interface for overall performance. The entire study reported in the thesis is organized as follows: Chapter 1 is a general introduction of hybrid nanocatalyst and their role in wide spectra of catalytic reactions in photo/electro catalysis as well as gas-phase reactions. This chapter describes the motivation behind modulating the interface between two or more nanostructures to obtain multifunctional nanocatalysts. Nan catalysts to achieve high throughput with active interfaces are elaborated while indicating the role of morphology, internal induced state, charge transfer, geometric, support, as well as electronic effect for enhanced performance. Motivation behind specific nanocatalyst hybrid, synthesis routes as well as characterization techniques are detailed in the respective chapters. Specific details for different hybrids are described in the following chapters. Chapter 2 describes the synthesis of high dense ultrathin Au wires on ZnO nanorods for electrocatalytic oxidation of ethanol, where the prerequisite step is the formation of amine-modified support. Oleylamine modification not only serves to anchor Au nanowires on ZnO but also passivates surface defects of ZnO, which in turn enhances the photocurrent. In addition to the stability, the support induces electronic effect on Au nanowires, which facilitates redox process at low potential. Most importantly, the support promotes the activity of Au nanowires upon photoirradiation, and thus leading to synergy between electro and photooxidation current. This is of immense importance for photofuel cell technologies. Moreover, the method enabled the first time electrocatalysis on these nanowires that revealed ultrathin nanowires are potentially interesting systems for catalysis applications provided they are stabilized by a suitable support. Chapter 3 deals with the growth of ultrathin Au nanowires on metal oxide (TiO2) coupled with graphene hybrid support in order to overcome the low conductivity of metal oxide. Oleylamine, used for growth of Au nanowires simultaneously functionalizes the support and leads to room temperature GO reduction. With respect to catalytic activity, we also synthesized the binary counterparts (rGO/Au, TiO2/Au ultrathin nanowires) to delineate the contribution of each of the components to the overall electrocatalytic oxidation of ethanol. Comparative analysis of photo and electrocatalytic activity between the different binary and ternary hybrids provides interesting information. Both, electronic effect of TiO2 and electrical conductivity of rGO add their specific beneficial to the nanowires, leading to superior ternary system. Chapter 4 rGO supported ultrathin Au nanowires exhibits high electrocatalytic performance for oxidation of borohydride with a lower onset potential compared to rGO/Au nanoparticles. Electrochemical impedance spectroscopy measurements display abnormal inductive behavior of the synthesized hybrids, indicative of Au surface reactivation. DFT calculations indicate that the origin of the high activity stems from the shift in the position of the Au d-band center. Chapter 5 Different aspect ratio ZnO nanostructures are obtained by varying the solvothermal reaction time. We observed a direct correlation between observed photocatalytic activity, measured photocurrent and length of the ZnO nanorods. Furthermore, photoresponse of the high aspect ratio ZnO nanorods are improved by attaching Au nanoparticles, intimate contact of two components leads to band bending. Thus, the synthesized ZnO/Au heterostructure favors for prominent separation of photogenerated charge carriers. Chapter 6 TiO2 and PbO/TiO2 hybrids are synthesized via non–hydrolytic sol–gel combustion method. Hybrid exhibits higher photocatalytic activity for the degradation of dye than TiO2. The estimated photogenerated species reveals that the origin of enhanced activity stems from the direct oxidization of dye via photogenerated hole rather than radicals. The semiconductors are matched based on their band edge positions, for the formation of energetic radicals to degrade the pollutants. Based on this study, we infer that semiconductors should not neglected (for example Si) based on calculated mismatch of their valence band edges position for photooxidation reaction via radicals. Chapter 7 describes the Pd dopant associated band engineering, a strategy for tuning the optoelectronic properties of ZnO towards enhanced photocatalytic activity. Incorporated Pd heterocation induces internal energy states within the ZnO band gap. The created energy level leads to trends mismatch between photocatalytic activity and measured photocurrent. Formed energy level arrests the photogenerated electrons, which make them not contribute for the photocurrent generation. Hence, the isolated photogenerated hole efficiently oxidizes the pollutants through hydroxyl radicals, and thus leads to enhanced photocatalytic activity. Chapter 8 employed Pd-substituted zinc stannate for CO oxidation as heterogeneous catalyst for the first time. Compared with SnO2 support, zinc stannate based materials exhibits abnormal sudden light-off profiles at selective temperatures. On the basis of DRIFT studies under relevant conditions, we find that the initially formed product gets adsorbed over the catalyst surface. It leads to the accumulation of carbonates as a consequence, both lattice oxygen mobility and further CO interactions are disabled. As soon as Sn redox nature dominates over the accumulated carbonates, this leads to sudden release of lattice oxygen, and thus leads to a sudden full conversion. Therefore, choosing the suitable support material greatly influences the nature of the light-off CO oxidation profile. Chapter 9 Although, reducible oxide supported gold nanostructures exhibits the highest CO oxidation activity; they still suffer from problems such as limited selectivity towards CO in the presence of H2. Both ex-situ and in-situ experiments demonstrate that, Au nanoparticles supported on Zn2SnO4 matrix selectively oxidizes CO. DRIFT experiments revealed that the involvement of OH groups leads to the formation of hydroxycarbonyl under PROX conditions. Chapter 10 This chapter discusses the conclusions for the previous chapters and highlights the possibilities for future scope for the developed nanocatalysts hybrids for energy and environmental applications.

Ce travail de thèse a concerné l’étude du comportement de nanoparticules d’électrocatalyseurs à base de Pt et Co déposées sur carbone de grande aire développée (Pt/C, PtCo/C et Pt3Co/C) en conditions représentative d’un fonctionnement à la cathode d’une pile à combustible à membrane échangeuse de protons. Dans une première phase, des électrodes modèles de ces matériaux ont été préparées sur des embouts de carbone vitreux compatibles avec une utilisation en montage d’électrode à disque tournant en milieu acide sulfurique, pour étudier l’évolution des performances électrochimiques (adsorption/désorption de l’hydrogène, Hupd, électrooxydation d’une monocouche de CO adsorbée à la surface du catalyseur : « CO-stripping », cinétique d’électroréduction de l’oxygène) après cyclage accéléré de potentiel (0,1 à 0,9 V vs. RHE et 0,6 à 0,9 V vs. RHE par créneaux d’une minute à chaque potentiel). Ces mesures électrochimiques ont été complétées par des observations statistiques par microscopie électronique en transmission (TEM) et fluorescence X (X-EDS) avant/après ces vieillissements sur des prélèvements représentatifs des couches actives. Les résultats montrent que le cobalt est irréversiblement oxydé/dissous des alliages Pt-Co et que la maturation d’Ostwald advient (pour le Pt) spécialement lorsque la borne inférieure de potentiel est fixée à 0,1 V vs. RHE. Ces mesures statistiques ont été confirmées par des expériences de MET en localisation identique (ILTEM), dans lesquelles les mêmes nanoparticules sont physiquement observées avant/après électrochimie réalisée sur la grille de microscopie[1]. Dans un second temps, des vieillissements identiques ont été mis en œuvre sur les mêmes matériaux électrocatalytiques en électrolyte polymère (Nafion), plus représentatif des conditions PEMFC, par utilisation d’une ultramicroélectrode à cavité et d’une « cellule sèche » dans laquelle le seul électrolyte est le Nafion (il n’y a donc pas d’électrolyte liquide). Dans ces conditions, plus proches des conditions réelles de fonctionnement d’une PEMFC, les mécanismes de dégradations sont différents de ceux observés en présence (d’excès) d’électrolyte liquide, parce que (entre autre), les ions Pt2+ formés à haut potentiel sont piégés dans le ionomère et donc plus faciles à redéposer sur les nanoparticules restantes. Le changement de morphologie (et composition) des nanoparticules de Pt/C (et Pt-Co/C) n’est donc pas identique en milieu H2SO4 et en milieu Nafion, ce qui montre que les tests réalisés en condition de laboratoire (en électrolyte liquide) ne sont pas forcément représentatifs de ce qui advient en PEMFC. Par extension, cette cellule sèche a été mise en œuvre pour mesurer les propriétés électrocatalytiques des différents électrocatalyseurs et, une fois encore, le milieu électrolyte liquide ne rend pas compte des performances observées en milieu « polymère ». Ces mesures ont été complétées par des observations statistiques en MET. Enfin, et il s’agit d’une innovation conséquente propre à ce travail, la méthode ILTEM a été employée pour des grilles de microscopie (supportant les électrocatalyseurs) n’ayant été utilisées qu’en interface avec un électrolyte polymère. Cela a permis de confirmer de manière quantitative et sur les mêmes grains de carbone / nanoparticules de Pt (ou Pt-Co) que les dégradations observées en milieu électrolyte liquide ne rendent pas compte de celles advenant en milieu polymère, la présence d’eau liquide jouant un rôle déterminant dans le premier cas (dissolution des espèces Pt2+/Co2+, oxydation du carbone, etc.). / In this study the oxygen reduction reaction (ORR) activity of Pt/C, Pt3Co/C and PtCo/C electrocatalysts supported on high surface area carbon (Vulcan XC-72) was correlated to their structural, morphological and compositional changes experienced after accelerated aging tests. The electrolytes were sulfuric acid at several concentrations and Nafion® ionomer membrane. These tests are based on different protocols that consisted of stepping the potential or keeping the electrode polarized at fixed potentials. The protocols which used steps consisted of stepping the potential during 1 minute for 15 hours overall successively between 0.9 and 0.1 V vs. ERH, 0.9 and 0.6 V vs. ERH, 1.05 and 0.10 V vs. ERH and 1.05 and 0.65 V vs. ERH. For the aging at fixed polarization (15 hours), the following potentials were used: 0.9, 0.6 and 0.1 V vs. ERH. After the 0.9 – 0.1 V vs. ERH aging in aqueous acidic solution, the Pt-Co/C catalysts showed no changes in the activity, while for Pt/C an improvement was seen. However for 1.05 – 0.10 V vs. ERH for Pt/C there was also an improvement while for the other catalysts there was a decrease of the activity. For all other protocols, a loss in activity was observed for all catalysts. Transmission electron microscopy (TEM) coupled with X-ray energy dispersive spectroscopy (X-EDS) analyses were used to characterize the as received and aged catalysts. A particularity of this work is the use of identical location transmission electron microscopy (ILTEM) technique, with the objective of analyzing the same electrode regions or particles before and after the accelerated ageing processes, so that it was possible to follow all the morphological, structural and compositional changes caused by the catalyst aging processes. The catalysts were compared before and after aging regarding the mean particle size, shape, particle density and composition and correlating these with the catalytic activity. Generally it was observed that the degradation correspond to carbon corrosion, coalescence, dissolution and re-precipitation of the catalyst particles for all aging protocols. The Pt/C catalyst, for example, for which an increase of particle mean size without any negative effect of agglomeration was observed, presented an improvement of the catalytic activity, while Pt-Co/C, in spite of the increase of the mean particle size and cobalt dissolution, presented worse or at most the same activity as that of the uncycled materials. Finally, the degradation mechanisms of the electrocatalysts aged in dry electrochemical environment using a Nafion® 115 membrane as polymer electrolyte were characterized by Identical Location Transmission Electron Microscopy, in conditions that perfectly mimic real PEMFC operation. The structural, morphological and compositional changes of the nanoparticles occurring during an accelerated stress test were bridged to changes of their intrinsic kinetics towards the oxygen reduction reaction in Nafion® 115 electrolyte, thanks to an ultramicroelectrode with cavity loaded with the catalyst. The unique setup used herein further enabled to compare the Nafion® environment with conventional liquid electrolyte in which accelerated stress tests are usually performed. Although the nanoparticles are modified upon ageing at Nafion® interface, the degradation processes are milder and different than those observed in liquid electrolyte, mostly following the absence of liquid water and the lack of ion mobility within the Nafion® membrane.

Research on new, environment-friendly, clean and efficient energy sources have contributed immensely to the development of new technologies for the generation and storage of electrical energy. Heterogeneous ‘electrocatalysis’ involves catalysis of redox reactions where the electrode material, termed as ‘electrocatalyst’ reduces the overpotential and maximizes the current for the processes occurring at the electrode/electrolyte interface. Efficient catalysts for hydrogen evolution reaction (HER), oxygen evolution reaction (OER), and oxygen reduction reaction (ORR) are of paramount importance for electrochemical energy generation and storage applications in water splitting, fuel cells and batteries. However, high cost of Pt catalysts that are commonly used for such applications restricts their commercial viability. In addition, there are issues related to poisoning of the surface under certain conditions. One particular case of direct methanol fuel cells involves problems of methanol tolerance as well. Hence, the on-going search in this direction, is to search for alternate catalysts that can match the performance of Pt. There is a quest for the development of stable and durable electrocatalysts/ supports for various electrochemical redox reactions particularly based on energy storage and conversion. The present thesis is structured in exploring the multi-functional aspects of ternary palladium phosphochalcogenides (PdPS and PdPSe) that possess layer-type structure with high crystallinity. They are semiconducting in nature and possess favorable electrochemical, electrical and optical properties. The chalcogenide compounds crystallize in orthorhombic symmetry with an indirect band gap close to 1.5 eV. The current study shows the versatility of ternary phosphochalcogenides in the bulk phase as well as in small sizes. The electrocatalytic activities of the chalcoenides are found to be dramatically improved by increasing the electrical conductivity by way of forming composites with reduced graphene oxide (rGO). The average crystallite size of the PdPS and PdPSe are 30 μm ±10 μm (figure 1). The composites are prepared by simple hydrothermal methods without use of any reducing agent and are characterized using various physico-chemical techniques. Figure 1. FESEM images of (a) PdPSe and (b) PdPS. In the present investigations, PdPS and its reduced graphene oxide composite (rGO-PdPS) are shown to be very efficient hydrogen evolution electrocatalysts (figure 2a). The bulk form of PdPS is found to be very active and the composite of PdPS with reduced graphene oxide improves the hydrogen evolution performance dramatically, even superior to state of the art, MoS2-based catalysts. Figure 2. (a) Linear sweep voltammograms of rGO, bulk PdPS, rGO-PdPS composite and 40 % Pt-C in 0.5 M H2SO4 solution (pH 0.8). Scan rate used is 1 mV s-1. (b) Tafel plots for PdPS, rGO, rGO-PdPS and 40 wt% Pt-C in 0.5 M H2SO4 at 1 mVs-1 scan rate. The Tafel slope and the exchange current density values associated with hydrogen evolution reaction are 46 mV dec-1 and 1.4 x 10-4 A cm-2 respectively (figure 2b). The stability of the PdPS-based catalyst is found to be excellent retaining same current densities even after thousand cycles. Moreover, post-HER characterization reveals the durability of the material even after cycling for a long time. Preliminary spectroelectrochemical investigations are attempted to gain further insight in to the HER. Subsequently, the PdPS and its composite are explored as ORR catalysts in alkaline medium. The composite of PdPS with rGO is formed to enhance the catalytic activity of pure PdPS and the electron transfer kinetics is found to be very favorable. The kinetics of the oxygen reduction reactions are followed by RDE/RRDE measurements. It is experimentally verified that the composite eletrocatalyst is very stable, efficient and methanol tolerant in alkaline medium. The characteristics of the composite catalyst are comparable with widely used standard Pt-C for ORR (figure 3a). Moreover, ternary phophochalcogenide, PdPS, combined with rGO shows good catalytic activity towards OER and it affords a current density of 10 mA cm-2 at an overpotential of η = 570 mV (figure 3b). Figure 3. (a) Comparative voltammograms for rGO, bulk PdPS, rGO-PdPS and 40 % Pt-C in 1M KOH at 1600 rpm. The potential is swept at a rate of 5 mVs-1. (b) Linear sweep voltammograms of oxygen evolution reaction on rGO-PdPS, PdPS and 40 % Pt-C in 1 M KOH electrolyte. Scan rate 5 mV s-1. Apart from its tri-functional electrocatalytic behavior, PdPS and its rGO composite act as an anode material for Li-ion batteries showing high storage capacity of lithium (figure 4). The capacity fading of bulk PdPS is analyzed using XRD and SEM. The introduction of rGO, a well-known conducting matrix, improves the performance. Palladium phosphorous selenide (PdPSe) and its composite with rGO (rGO-PdPSe) are also explored as electrocatalysts for HER, ORR and OER. They show the tri¬functional electrocatalytic behavior as well. Figure 4. Discharge capacity as a function of number of cycles for PdPS, rGO rGO-PdPS electrode at current density of 35 mAg-1 in rechargeable lithium ion battery. The next chapter deals with single or few layer PdPS where layer-type PdPS is exfoliated by several methods such as ultra-sonication and solvent exfoliation. Various microscopic and spectroscopic techniques have been used to characterize the material. These sheets show significantly improved electrocatalytic activity towards ORR and HER with notably low onset potential and low Tafel slopes. The charge storage capacity also increases by an order from its bulk counterpart. The catalyst shows excellent stability for HER and good methanol tolerance behavior towards ORR is also observed. This opens up possibilities for applications of few-layer ternary phosphosulphides in energy conversion and storage. However, one should be cautious since the exfoliation results in a slightly different composition of the material. Different aspects of electrodeposition of gallium nanoparticles on exfoliated graphite surfaces from aqueous acidic solution forms part of the next study. The electrodeposited surface is characterized by various microscopic and spectroscopic techniques. The presence of surface plasmon peak in the visible region has led us to explore the use of Ga on EG for SERS studies. This preliminary work shows that the Raman signal of R6G is enhanced in the presence of Ga deposited on EG surface. The research work presented in the next part of the thesis deals with the preparation, physicochemical, spectroscopic characterization of room temperature molten electrolytes based on amides. Room temperature ternary molten electrolyte involving a combination of acetamide, urea and gallium nitrate salt is prepared and the molten eutectic is characterized. An electrochemical process is developed for depositing gallium nitride from the ternary molten electrolyte on Au electrode. Gallium ion is reduced at low potentials while nitrate ion is reduced to produce atomic nitrogen, forming gallium nitride under certain conditions. Au coated TEM grid is used for patterning gallium nitride (figure 5). The deposited gallium nitride is further annealed at high temperature to increase the crystalinity and improve the stoichiometry of gallium nitride. Figure 5. The FESEM image of patterned gallium nitride deposited on Au coated TEM grid. Elemental mapping of Ga and N from the same region is given. The last chapter explores the prepration and uses of textured GaN tubes synthesized from GaOOH rod-like morphology. The precursor material is prepared by simple hydrothermal technique, maintaining certain value for the pH of the solution. The thermal treatment under ammonia atmosphere leads to highly crystalline, single phase textured tube- like morphology. The as-prepared material is explored as photoanodes in photoelectrochemical water splitting, dye sensitized solar cells and active substrate for SERS. The appendix-I discusses the Na-ion storage capacity by rGO-PdPS composite whereas appendix-II deals with the synthesis of InN and FeN from ternary molten electrolyte. (For figures pl refer the abstract pdf file)