<p>Thermistor material can be used to fabricate un-cooled IR detectors their figure of merit is the Temperature Coefficient of Resistance (TCR). Ge dots in Si can act as a thermistor material and they have a theoretical TCR higher than for SiGe layers but they suffer from intermixing of Si into the Ge dots. Ge dots were grown on unstrained or strained Si layers and relaxed or strained SiGe layers at temperatures of 550 and 600°C by reduced pressure chemical vapor deposition (RPCVD). Both single and multilayer structures where grown and characterized. To achieve a strong signal in a thermal detector a uniform shape and size distribution of the dots is desired. In this thesis work, an endeavor has been to grow uniform Ge dots with small standard deviation of their size. Scanning electron microscopy (SEM) and Atomic force microscopy (AFM) have been used to characterize the size and shape distribution of Ge dots. Ge contents measured with Raman spectroscopy are higher at lower growth temperatures. Simulation of TCR for the most uniform sample grown at 600°C give 4.43%/K compared to 3.85%/K for samples grown at 650°C in a previous thesis work.</p><p>Strained surfaces increases dot sizes and make dots align in crosshatched pattern resulting in smaller density, this effect increases with increasing strain.</p><p>Strain from buried layers of Ge dots in a multilayer structure make dots align vertically. This alignment of Ge dots was very sensitive to the thickness of the Si barrier layer. The diameter of dots increase for each period in a multilayer structure. When dots are capped by a Si layer at the temperature of 600°C intermixing of Si into the Ge dot occurs and the dot height decrease.</p>

<p>This thesis describes and evaluates a number of algorithms for reducing fixed pattern noise in image sequences. Fixed pattern noise is the dominantnoise component for many infrared detector systems, perceived as a superimposed pattern that is approximately constant for all image frames. </p><p>Primarily, methods based on estimation of the movement between individual image frames are studied. Using scene-matching techniques, global motion between frames can be successfully registered with sub-pixel accuracy. This allows each scene pixel to be traced along a path of individual detector elements. Assuming a static scene, differences in pixel intensities are caused by fixed pattern noise that can be estimated and removed. </p><p>The algorithms have been tested by using real image data from existing infrared imaging systems with good results. The tests include both a two-dimensional focal plane array detector and a linear scanning one-dimensional detector, in different scene conditions.</p>

<p>Multiple myeloma (MM) is an incurable B-cell malignancy mainly localized to the bone marrow. Our aim was to examine the growth- and survival-promoting role of the IGF-IR and its downstream signaling components in MM cells to identify potential targets for therapy. </p><p>Octreotide, a somatostatin analog that has been demonstrated to interfere with the actions of IGF-I, induced growth inhibition in both IL-6-dependent and IL-6-independent MM cell lines expressing the somatostatin receptors sst2, sst3 and sst5. Additionally, a slight pro-apoptotic effect could be observed in a few cell lines. In primary MM cells octreotide induced apoptosis, an effect that was abrogated by exogenously added IGF-I, but not by IL-6.</p><p>Inhibition of IGF-I signaling in Karpas 707 cells, using either the anti-IGF-IR antibody αIR3 or the PI 3-K inhibitors LY294002 and wortmannin, increased sensitivity to apoptosis induced by dexamethasone. Exogenously added IGF-I prevented dexamethasone-induced apoptosis, an effect that could partly be mimicked by the pharmacological GSK-3β inhibitors LiCl and SB415286. Thus, we suggest the GSK-3β as an important mediator of the anti-apoptotic effects of IGF-IR signaling in MM.</p><p>Using rapamycin we selectively inhibited mTOR, a phosphoprotein downstream of the IGF-IR. In MM cell lines rapamycin induced G0/G1-arrest, an effect being associated with an increase of the cyclin-dependent kinase inhibitor p27 and a decrease of the cyclins D2, D3 and E. Interestingly, in primary MM cells rapamycin induced apoptosis. Moreover, rapamycin potentiated dexamethasone-induced apoptosis, an effect that was associated with a downregulation of the anti-apoptotic protein survivin. Strikingly, the combinatorial treatment with rapamycin and dexamethasone suppressed the anti-apoptotic effects of exogenously added IGF-I and IL-6, thus suggesting this drug-combination to be active also in vivo. </p><p>Two newly developed, selective IGF-I RTK inhibitors proved to be very effective in MM cell lines and in primary MM cells providing 50-90% growth inhibition within 48 h of incubation. The inhibitors induced massive apoptosis together with a prominent cell cycle arrest in the G2/M-phase. Importantly, the IGF-I RTK inhibitors downregulated the tyrosine phosphorylation of the IGF-IR β-chain but not of the insulin receptor β-chain. </p><p>In conclusion, the IGF-IR potently promotes growth and survival of MM cells. Therefore, interfering with the IGF-IR signaling pathway might be a suitable strategy to improve MM treatment.</p>

<p>In this thesis, factors important in tableting operations and for tablet properties have been studied and characterised by different spectroscopic techniques as well as by some more conventionally used particle characterisation techniques. The spectroscopic techniques solid-state NMR, FT-IR and NIR spectroscopy, proved to be valuable tools in the estimation of particle and tablet properties, offering both specificity and sensitivity in the measurements. Because of the large amount of information obtained in a spectrum, multivariate data analysis was in some cases used in the processing of the spectral data. Correlations between the solid state structure measured by spectroscopy and the particle and tablet properties could be obtained including useful prediction models.</p><p>The surface area obtained using different principles has in this thesis been shown to reflect different properties and tableting behaviour of a collection of pharmaceutical materials. The particle shape and the external surface area of the powders measured by permeametry, were found to be important factors for the tensile strength of tablets made of hydroxypropyl methylcellulose. Furthermore, the external surface area could be used to access dominating interparticulate bonding mechanisms in compacts of different materials by normalising the tablet tensile strength for the tablet surface area. It was also shown that for materials prone to develop solid bridges, the actual surface area participating in the bonding was more important than the average interparticulate distance. </p><p>When studying the properties of microcrystalline cellulose and cellulose powder from the alga <i>Cladophora</i> sp., the cellulose fibril surface area estimated by solid-state NMR resulted in better correlations to the tableting behaviour and to tablet disintegration than the external permeametric surface area did. It was suggested that the difference in fibril surface area of the two celluloses was the primary factor responsible for properties like the crystallinity and the disintegration of the tablets.</p>

This study evaluated the applicability of remote sensing instrumentation for site- specific management of abiotic and biotic stress on cotton grown under a center pivot. Three different irrigation regimes (100%, 75%, and 50% ETc) were imposed on a cotton field to 1) monitor canopy temperatures of cotton with infrared thermometers (IRTs) in order to pinpoint areas of biotic and abiotic stress, 2) compare aerial infrared photography to IRTs mounted on center pivots to correlate areas of biotic and abiotic stress, and 3) relate yield to canopy temperatures. Pivot-mounted IRTs and IR camera were able to differentiate water stress between the irrigation regimes, however, only the IR camera was effectively able to distinguish between biotic (cotton root rot) and abiotic (drought) stress with the assistance of groundtruthing. The 50% ETc regime had significantly higher canopy temperatures, which were reflected in significantly lower lint yields when compared to the 75% and 100% ETc regimes. Deficit irrigation up to 75% ETc had no impact on yield, indicating that water savings were possible without yield depletion.

Diamond is a promising material for high-power, high-frequency and high- temperature electronics applications, where its outstanding physical properties can be fully exploited. It exhibits an extremely high bandgap, very high carrier mobilities, high breakdown field strength, and the highest thermal conductivity of any wide bandgap material. It is therefore an outstanding candidate for the fastest switching, the highest power density, and the most efficient electronic devices obtainable, with applications in the RF power, automotive and aerospace industries. Lightweight diamond devices, capable of high temperature operation in harsh environments, could also be used in radiation detectors and particle physics applications where no other semiconductor devices would survive. The high defect and impurity concentration in natural diamond or high-pressure-high-temperature (HPHT) diamond substrates has made it difficult to obtain reliable results when studying the electronic properties of diamond. However, progress in the growth of high purity Single Crystal Chemical Vapor Deposited (SC-CVD) diamond has opened the perspective of applications under such extreme conditions based on this type of synthetic diamond. Despite the improvements, there are still many open questions. This work will focus on the electrical characterization of SC-CVD diamond by different measurement techniques such as internal photo-emission, I-V, C-V, Hall measurements and in particular, Time-of-Flight (ToF) carrier drift velocity measurements. With these mentioned techniques, some important properties of diamond such as drift mobilities, lateral carrier transit velocities, compensation ratio and Schottky barrier heights have been investigated. Low compensation ratios (ND/NA) &lt; 10-4 have been achieved in boron-doped diamond and a drift mobility of about 860 cm2/Vs for the hole transit near the surface in a lateral ToF configuration could be measured. The carrier drift velocity was studied for electrons and holes at the temperature interval of 80-460 K. The study is performed in the low-injection regime and includes low-field drift mobilities. The hole mobility was further investigated at low temperatures (10-80 K) and as expected a very high mobility was observed. In the case of electrons, a negative differential mobility was seen in the temperature interval of 100-150K. An explanation for this phenomenon is given by the intervally scattering and the relation between hot and cold conduction band valleys. This was observed in direct bandgap semiconductors with non-equivalent valleys such as GaAs but has not been seen in diamond before. Furthermore, first steps have been taken to utilize diamond for infrared (IR) radiation detection. To understand the fundamentals of the thermal response of diamond, Temperature Coefficient of Resistance (TCR) measurements were performed on diamond Schottky diodes which are a candidate for high temperature sensors. As a result, very high TCR values in combination with a low noise constant (K1/f) was observed.

In this thesis, factors important in tableting operations and for tablet properties have been studied and characterised by different spectroscopic techniques as well as by some more conventionally used particle characterisation techniques. The spectroscopic techniques solid-state NMR, FT-IR and NIR spectroscopy, proved to be valuable tools in the estimation of particle and tablet properties, offering both specificity and sensitivity in the measurements. Because of the large amount of information obtained in a spectrum, multivariate data analysis was in some cases used in the processing of the spectral data. Correlations between the solid state structure measured by spectroscopy and the particle and tablet properties could be obtained including useful prediction models. The surface area obtained using different principles has in this thesis been shown to reflect different properties and tableting behaviour of a collection of pharmaceutical materials. The particle shape and the external surface area of the powders measured by permeametry, were found to be important factors for the tensile strength of tablets made of hydroxypropyl methylcellulose. Furthermore, the external surface area could be used to access dominating interparticulate bonding mechanisms in compacts of different materials by normalising the tablet tensile strength for the tablet surface area. It was also shown that for materials prone to develop solid bridges, the actual surface area participating in the bonding was more important than the average interparticulate distance. When studying the properties of microcrystalline cellulose and cellulose powder from the alga Cladophora sp., the cellulose fibril surface area estimated by solid-state NMR resulted in better correlations to the tableting behaviour and to tablet disintegration than the external permeametric surface area did. It was suggested that the difference in fibril surface area of the two celluloses was the primary factor responsible for properties like the crystallinity and the disintegration of the tablets.

Multiple myeloma (MM) is an incurable B-cell malignancy mainly localized to the bone marrow. Our aim was to examine the growth- and survival-promoting role of the IGF-IR and its downstream signaling components in MM cells to identify potential targets for therapy. Octreotide, a somatostatin analog that has been demonstrated to interfere with the actions of IGF-I, induced growth inhibition in both IL-6-dependent and IL-6-independent MM cell lines expressing the somatostatin receptors sst2, sst3 and sst5. Additionally, a slight pro-apoptotic effect could be observed in a few cell lines. In primary MM cells octreotide induced apoptosis, an effect that was abrogated by exogenously added IGF-I, but not by IL-6. Inhibition of IGF-I signaling in Karpas 707 cells, using either the anti-IGF-IR antibody αIR3 or the PI 3-K inhibitors LY294002 and wortmannin, increased sensitivity to apoptosis induced by dexamethasone. Exogenously added IGF-I prevented dexamethasone-induced apoptosis, an effect that could partly be mimicked by the pharmacological GSK-3β inhibitors LiCl and SB415286. Thus, we suggest the GSK-3β as an important mediator of the anti-apoptotic effects of IGF-IR signaling in MM. Using rapamycin we selectively inhibited mTOR, a phosphoprotein downstream of the IGF-IR. In MM cell lines rapamycin induced G0/G1-arrest, an effect being associated with an increase of the cyclin-dependent kinase inhibitor p27 and a decrease of the cyclins D2, D3 and E. Interestingly, in primary MM cells rapamycin induced apoptosis. Moreover, rapamycin potentiated dexamethasone-induced apoptosis, an effect that was associated with a downregulation of the anti-apoptotic protein survivin. Strikingly, the combinatorial treatment with rapamycin and dexamethasone suppressed the anti-apoptotic effects of exogenously added IGF-I and IL-6, thus suggesting this drug-combination to be active also in vivo. Two newly developed, selective IGF-I RTK inhibitors proved to be very effective in MM cell lines and in primary MM cells providing 50-90% growth inhibition within 48 h of incubation. The inhibitors induced massive apoptosis together with a prominent cell cycle arrest in the G2/M-phase. Importantly, the IGF-I RTK inhibitors downregulated the tyrosine phosphorylation of the IGF-IR β-chain but not of the insulin receptor β-chain. In conclusion, the IGF-IR potently promotes growth and survival of MM cells. Therefore, interfering with the IGF-IR signaling pathway might be a suitable strategy to improve MM treatment.

Crystallographic and spectroscopic studies have been performed of structures, coordination and chemical bonding for series of trivalent metal ions solvated by two oxygen-coordinating solvents, water and dimethyl sulfoxide (DMSO). The hydrated scandium(III) and lanthanoid(III) ions, La to Lu, are surrounded by tricapped trigonal prisms of aqua ligands in the isomorphous series of trifluoromethanesulfonates, [M(H2O)n](CF3SO3)3. For the smallest ions, M = Er, Tm, Yb, Lu, Sc, the hydration numbers decrease, n = 8.96(5), 8.8(1), 8.7(1), 8.5(1), 8.0(1), respectively, with decreasing size of the ion. The crystal structures at ambient temperature indicate randomly distributed vacancies of the capping oxygen atoms, and 2H solid-state NMR of the diamagnetic [M(H2O)n](CF3SO3)3, M = Sc, Lu, Y and La compounds revealed increasing mobility of the water ligands in the coordination sphere with increasing temperature, also for the fully nonahydrated LaIII and YIII ions. The stretching force constants of the Ln-O bonds, evaluated from vibrational spectroscopy, increased from 0.81 to 1.16 N cm-1 for the Ln-6O trigonal prism in a smooth correlation with the bond distances from La to Lu. For the capping Ln-3O bonds the increase from 0.49 to 0.65 N cm-1 reflects the increased ligand-ligand repulsion with decreasing ion size. This is also the reason for the water deficiency of the Er, Tm, Yb, Lu and Sc salts, and for [Sc(H2O)8.0](CF3SO3)3 the repulsion induced a phase transition at about 185 K that, by low temperature crystallography, was found to distort the coordination of water molecules toward a monocapped trigonal prism around the scandium(III) ion. All crystal structures of the octakis(dimethyl sulfoxide)lanthanoid(III) iodides comprise discrete [Ln(dmso)8]3+ complexes surrounded by iodide ions. The lanthanum(III) and praseodymium(III) compounds crystallize in the orthorhombic space group Pbca with more efficient packing than for the heavier and smaller ions in the lanthanoid series, which crystallize in the monoclinic space group P21/n. The group 13 metal ions, aluminium(III), gallium(III), indium(III), thallium(III), and also scandium(III) of group 3, form crystalline hexakis(dimethyl sulfoxide) solvates in the space group R 3, with octahedral MO6 coordination entities, which are increasingly compressed along one threefold axis for increasing ionic size. EXAFS measurements on the solvated ions display similar M-O bond distances in dimethyl sulfoxide solution as in the solid solvates. For all the solid dimethyl sulfoxide solvates the strength and nature of the metal-oxygen bond has been evaluated by normal coordinate analysis of vibrational spectra, and correlated with the S-O stretching vibrational mode. Distortions from regular octahedral six coordination are discussed for the hydrated isoelectronic soft mercury(II) and thallium(III) ions in the solid bisaquamercury(II) and trisaquatallium(III) trifluoromethanesulfonates, in terms of pseudo Jahn-Teller effects (PJTE). Mercury(II), generally more strongly influenced by PJTE distortions, displays a 2 + 4 Hg-O coordination forming chains that are held together in sheets by hydrogen bonds and in layers by van der Waals interactions, which explain the fragile structure of the crystals.

There is a growing awareness of the risks of pollution in biological systems and one potential problem is the synthetic antioxidants, used for e.g. the stabilisation of polymeric materials. Natural antioxidants are an interesting alternative, if the high efficiency and thermal stability of the synthetic compounds can be reached. In the work described in this thesis, vitamin E (alfa-tocopherol) was studied as a natural antioxidant for the stabilisation of one of the major plastics, polyethylene (PE). The dependence of the surrounding environment for the efficiency of alfa-tocopherol in polyethylene (PE), throughout thermal aging, was characterised by sensitive techniques. Two techniques which have shown a high sensitivity in oxidation detection of polymers; chemiluminescence (CL) and gas chromatographic analysis, were compared with the commonly used methods, infrared spectroscopy (FT-IR) and thermal analysis. Three different additive systems were selected as active domains for -tocopherol in PE. Two of these contained carboxylic acid groups, poly (ethylene-co-acrylic acid) (EAA) and polyTRIM/PAA core-shell particles (Core), and the third, oat starch, had no such groups. The additives containing carboxylic groups improved the long-term efficiency of alfa-tocopherol in PE, according to carbonyl index measurements made by FT-IR, while the additive without carboxylic acid groups gave no improvement. The amount of carboxylic acids emitted from the materials after thermal aging, assessed by head-space solid-phase microextraction (HS-SPME) and gas chromatography-mass spectroscopy (GC-MS), also showed that EAA increased the antioxidant efficiency of alfa-tocopherol, whereas the Core system showed lower antioxidant efficiency. Reference systems containing the synthetic antioxidant Irganox 1076 and EAA or oat starch had the same performance as the materials stabilised with only the antioxidants. CL measurements in an inert atmosphere (TLI) have earlier been shown to give earlier oxidation detection than carbonyl index measurements in unstabilised PE. In this work, the TLI analysis and the carbonyl index measurements had the same sensitivity in the detection of oxidation in the stabilised materials. Assessment of low-molecular weight carboxylic acids in PE during the aging was made by gas chromatographic analysis together with solid-phase extraction. Propanoic acid showed the best correlation with the carbonyl index measurements, even if the carbonyl index showed earlier detection of oxidation. It was also found that TLI and CL in an oxidative atmosphere (CL-OIT) had the same sensitivity and were in accordance for all of the materials, with exception of the materials containing EAA and alfa-tocopherol or Irganox 1076. CL-OIT was also compared to the oxygen induction time determined by thermal analysis. / QC 20100921