Title: Monte Carlo Simulations of the Tile Calorimeter and Measurement of the Z → ττ Cross Section with the ATLAS Detector Author: Mgr. Jana Nováková Department: Institute of Particle and Nuclear Physics (IPNP) Supervisor: RNDr. Tomáš Davídek, PhD., IPNP Supervisor's e-mail address: davidek@ipnp.troja.mff.cuni.cz Abstract: The Monte Carlo simulations of the Tile calorimeter in the ATLAS experiment at the LHC, especially the electronic noise and multiple interactions (co-called pile-up), are discussed in the thesis. A good agreement in the cell energy distribution between data and Monte Carlo simulations is found. The cross section measurement of Z → ττ events with the ττ invariant mass between 66 and 116 GeV with the ATLAS experiment is described in the next part of the thesis. Data samples collected during 2011 corresponding to the integrated luminosity of 1.34 - 1.55 fb−1 are used for the analysis. The measurements are performed in three different final states depending on the decay mode of the τ leptons. The measurement in the channel with one τ lepton decaying leptonically into the electron + neutrinos (schematically τ → e + νe + ντ ) and the other one hadronically (schematically τ → hadrons + ντ ), especially the calculation of the nominal cross section and the evaluation of the systematic...

The Standard Model has granted exquisite power to predict the behaviour of high-energy particle collisions. It is not, however, without conceptual and empirical weaknesses. Several theories have been proposed which aim to resolve these difficulties. This thesis describes searches for two such theories: models of extra spatial dimensions, and supersymmetry. The Large Hadron Collider has extended the frontiers of energy and intensity in particle physics. In 2015, the LHC resumed proton–proton collisions at a centre-of-mass energy of 13 TeV. This increase over previous operation grants an enhancement in sensitivity to many processes beyond those of the Standard Model. Extra-dimensional theories address the hierarchical nature of the Standard Model. The lowered fundamental scale of gravity in these models allows a rich phenomenology at energies which may be accessible to the LHC. Some models predict the formation of microscopic black holes, which are the target of an analysis of collisions recorded by the ATLAS detector in 2015. No significant deviations from Standard Model predictions were observed. The constraints inferred on the parameters of the model are a significant advance on previous results. Lepton flavour is conserved in the Standard Model. This is not the result of a known fundamental symmetry, however. The latter part of this thesis proposes a search examining asymmetries of charge and flavour in the eμ final state. Models of supersymmetry with an R-parity-violating λ'₂₃₁ coupling are taken as motivation. The strategy is developed using collision data recorded by ATLAS in 2015 and 2016, and the most significant biasing effects are addressed.

Enquanto todos os modelos com neutrinos massivos de Majorana levam ao mesmo operador efetivo de dimensão d = 5, que não conserva número leptônico, os operadores de dimensão d = 6, obtidos a baixas energias, conservam número leptônico e são diferentes dependendo do modelo de alta energia da nova física. Derivamos os operadores de dimensão d = 6 que são característicos de modelos Seesaw genéricos, no qual a massa do neutrino resulta do intercâmbio de campos pesados que podem ser tanto singletos fermiônicos, tripletos fermiônicos ou tripletos escalares. Os operadores resultantes podem conduzir a efeitos observáveis no futuro próximo, se os coeficientes dos operadores de dimensão d = 5 e d = 6 são desacoplados. Neste trabalho apresentamos o modelo violação mínima de sabor no contexto do modelo seesaw tipo III, no qual é possível obter tal desacoplamento. Isto permite reconstruir a estrutura de sabor a partir dos valores das massas dos neutrino leves e dos parâmetros de mistura, mesmo na presença de fases de violação CP. / While all models of Majorana neutrino masses lead to the same dimension five effective operator, which does not conserve lepton number, the dimension six operators induced at low energies conserve lepton number and differ depending on the high energy model of new physics. We derive the low-energy dimension six operators which are characteristic of generic Seesaw models, in which neutrino masses result from the exchange of heavy fields which may be either fermionic singlets, fermionic triplets or scalar triplets. The resulting operators may lead to effects observable in the near future, if the coefficients of the dimension five and six operators are decoupled. In this work we present the model of minimal avor violation in the context of the type III seesaw model, in which it is possible to obtain the decoupling mentioned before. This allows to reconstruct the avour structure of the model from the values of the light neutrino masses and mixing parameters, even in the presence of CP-violating phases.

Submitted by Mario BC (mario@bc.ufrpe.br) on 2017-10-04T13:53:52Z No. of bitstreams: 1 Andreza Goncalves dos Santos.pdf: 1316057 bytes, checksum: a335fe2e3aa71d2b9eaa5e68d04d3cca (MD5) / Made available in DSpace on 2017-10-04T13:53:52Z (GMT). No. of bitstreams: 1 Andreza Goncalves dos Santos.pdf: 1316057 bytes, checksum: a335fe2e3aa71d2b9eaa5e68d04d3cca (MD5) Previous issue date: 2017-02-16 / To lawns could be established by seeds, nevertheless is necessary improve the germinate rates and increase the sanitary quality of the seeds. Thus, generally the lawns implantation is established by vegetative propagules that are small cores of sod or pieces of stolons or rhizomes with leaves. Therefore, the vegetative propagules capacity of storage and transport to introduce a new material should be known, as it will impact on the establishment of the lawn. The objective of this work was to determinate the physiological and sanitary quality of the seeds of Paspalum notatum and P. lepton after use overcoming dormancy methods and evaluate the tolerance to low temperature storage of Axonopus parodii, P. notatum and P. lepton vegetative propagules. To determinate the physiological and sanitary quality, the seeds were submitted to the following treatments: concentrated H2SO4 (98%) for 15 minutes and KNO3 (0,2%). Germination, vigor (first count and emergence in soil), germination speed index and sanity were evaluated. The results obtained allowed to conclude that the chemical scarification with concentrated sulfuric acid, for 15 minutes, provided the increase of the germination of P. notatum e P. lepton seeds and reduction of fungal incidence. To evaluate the tolerance to low temperature storage of vegetative propagules of Axonopus parodii, Paspalum notatum and P. lepton for lawn implantation, the propagules were stored in a cold chamber at 6,5°C and 85% UR, according to the treatments, in: control with zero storage day (0 DA); 2 DA; 4 DA; 6 DA; 8 DA; and 10 DA. The following characteristics were evaluated before planting: initial fresh mass; fresh mass after storage, before planting; and loss of fresh mass. After 40 days of planting were evaluated: survival rate; soil cover capacity; height; tillers production; and total dry mass. Despite the loss of fresh mass, storage at 6,5°C until 10 days preserved the viability of the vegetative propagules of the Axonopus parodii and Paspalum accessions, maintaining the survival rate, soil coverage and tiller emission. / Os gramados podem ser implantados por sementes, porém, é necessário aumentar a taxa de germinação e a qualidade sanitárias das sementes. Por isso, geralmente a implantação de gramados é por meio de propágulos vegetativos, compostos por pequenos núcleos de grama com rizoma ou estolões e folhas. Portanto, a capacidade de armazenamento e transporte dos propágulos para a introdução de um novo material devem ser conhecidos, pois irá impactar no estabelecimento satisfatório do gramado. O objetivo deste trabalho foi avaliar a qualidade fisiológica e sanitária das sementes de Paspalum notatum e P. lepton após a utilização de métodos de superação de dormência e a tolerância ao armazenamento à baixa temperatura de propágulos vegetativos de acessos de Axonopus parodii, P. notatum e P. lepton para implantação de gramados. Para avaliar a qualidade fisiológica e sanitária das sementes de Paspalum notatum e P. lepton após a utilização de métodos de superação de dormência, as sementes foram submetidas aos seguintes tratamentos pré-germinativos: testemunha, H2SO4 concentrado (98%) por 15 minutos e KNO3 (0,2%). Foram avaliados a germinação, primeira contagem, emergência em solo, índice de velocidade de germinação e sanidade. Os resultados obtidos permitiram concluir que a escarificação química com ácido sulfúrico concentrado, por quinze minutos, propiciou maior germinação sementes de P. notatum e P. lepton e redução da incidência fúngica. Para avaliar a tolerância ao armazenamento à baixa temperatura de propágulos vegetativos estes foram armazenados em câmara fria à 6,5°C e 85%UR, conforme os tratamentos, em: testemunha com zero dia de armazenamento (0 DA); 2 DA; 4 DA; 6 DA; 8 DA; e 10 DA. Foram avaliadas as seguintes características antes do plantio: massa fresca inicial; massa fresca após o armazenamento antes do plantio; e perda de massa fresca. Após 40 dias do plantio foram avaliadas: taxa de pegamento; capacidade de cobertura do solo; altura; produção de perfilhos; e massa seca total. Apesar da perda de massa fresca, o armazenamento a 6,5°C por até 10 dias conservou a viabilidade dos propágulos vegetativos dos acessos de Axonopus parodii e Paspalum, mantendo boa taxa de pegamento, de cobertura do solo e de emissão de perfilhos.

Charged lepton flavour violating processes are highly suppressed in the standard model, but they are predicted to be enhanced in several new physics extensions including supersymmetry and models with leptoquarks or compositeness. Data collected with the BaBar detector at the SLAC PEP-II e$^+$e$^-$ asymmetric collider at a centre-of-mass energy of 10.36~GeV were used to search for electron-muon flavor violation in $\Upsilon (3S)\rightarrow e^{\pm}\mu^{\pm}$ decays. The search was conducted using a data sample in which 118 million $\Upsilon (3S)$ mesons were produced, corresponding to an integrated luminosity of 27~$fb^{-1}$. There is no evidence of a signal in the $\Upsilon (3S)$ data and we report our results as upper limits on $\mathcal{B}(\Upsilon(3S)\rightarrow e^{\pm}\mu^{\mp})<3.6\times10^{-7}\mathrm{at~ 90\%~ CL}$. / Graduate

This thesis presents work carried out using data from the LHCb experiment during the first three years of data taking, 2010 - 2012. A study of the effects of radiation damage on the silicon sensors of the LHCb Vertex Locator is performed, with an emphasis on the implications for the long term performance of the detector. Following three years of operation the sensors have received a maximum delivered neutron equivalent fluence of approximately 1.6E12 per square centimeter, leading to a number of radiation induced effects. In particular the change in charge collection efficiency and signal/noise with fluence is compared to theoretical expectations, and the current trends are extrapolated to the fluences expected at the end of the LHCb detector lifetime. The development of an unexpected effect due to the structure of the routing lines in the sensors is described in detail. Searches for lepton flavour and baryon number violating decays of the tau lepton using the 2011 LHCb dataset are described. Observation of any lepton flavour or baryon number violation would be an unambiguous sign of new physics, whilst setting improved limits helps to constrain a number of Beyond the Standard Model theories. First LHCb limits are set on the branching fractions of the decays tau- to mu- mu+ mu-, tau- to anti-proton mu+ mu- and tau- to proton mu- mu-, with these results also representing the first limits on lepton flavour violating tau decays at a hadron collider. The limit on tau- to mu- mu+ mu- is expected to approach the world's best result from Belle in the coming years whilst the tau- to anti-proton mu+ mu- and tau- to proton mu- mu- results constitute the first limits on the branching fractions of these decays. The future prospects for these measurements with further data are briefly described.

The COVID-19 pandemic brought increased need for measuring human temperature. This thesis deals with solution of using low-cost thermal camera module FLIR Lepton 3.5 for measuring human forehead temperature and examines the real usability of this in terms of an accuracy. In the beginning, I describe various methods of measuring temperature and factors, which can influence the measurement. Subsequently, I examine various factors influencing human body and surface temperature. As of result of thesis is full design and implementation of thermal image system for temperature measurement, which I tested in different environmental conditions and compared its the precision against medical contactless infrared thermometer.

The Standard Model of elementary particles (SM) predicts the existence of a neutral scalar Higgs boson. However, there are also extensions of the SM (such as the MSSM) in which a number of Higgs bosons is predicted. Especially the additional presence of pseudoscalar and charged Higgs bosons represents one of the crucial differences between the SM and its exten- sions. This work develops a method for determination of the spin and parity of the Higgs boson in several H → ττ decays, namely: H→ τ+ τ− → (h+ ντ )(h− ¯ντ ), H→ τ+ τ− → ( + ντ ¯ν )(π− ¯ντ ) and H→ τ+ τ− → ( + ντ ¯ν )( − ¯ντ ν ), where h denotes π or ρ meson. The method is based on the angular and energy correlations of charged final products from the decays mentioned above. Additionally, the work studies the possibility of signal (Higgs boson decay) and background (Z → ττ decay) discrimination, when one considers a decaying boson with spin 1. All calcula- tions are done in the leading order of perturbation theory. 1

La notion de symétrie de jauge est au coeur de notre compréhension de l'interaction électrofaible et permet d'expliquer l'ensemble des observations expérimentales actuelles. Pourtant, l'incompatibilité intrinsèque entre l'invariance de jauge et la masse des particules nécessite d'introduire une nouvelle particule, le boson de Higgs, toujours non observée à ce jour. Cette thèse présente l'analyse de 7.3/fb de collisions protons-antiprotons à sqrt{s} = 1.96 TeV enregistrées par le détecteur D0 au Tevatron en vue de la recherche du boson de Higgs dans l'état final mu+tau. Cette analyse vient compléter les canaux principaux dimuons, électron-muon et diélectrons en exploitant également la désintégration H -> WW -> lvlv, majoritaire dans la fenêtre de masse accessible au Tevatron. L'état final contenant un lepton tau, leur identification parmi les jets a été améliorée d'environ 15% grâce au développement de plusieurs idées : l'ajustement des paramètres du réseau de neurones d'identification, la prise en compte de certaines dépendances cinématiques des performances de l'algorithme, l'exploitation du temps de vie du lepton tau et une étude exhaustive visant à inclure la mesure du détecteur de pieds de gerbe dans le processus d'identification. Dans un second temps, la recherche du boson de Higgs dans l'état final mu+tau étant dominée par le bruit de fond W+jets (où un jet est faussement identifié comme un lepton tau), une méthode a été élaborée pour obtenir une modélisation convenable de ce bruit de fond, non fournie par la simulation par défaut. Cette méthode est basée, entre autres, sur l'étude de la corrélation de charge entre le muon et le candidat tau qui permet de mesurer ce bruit de fond dans les données en excluant la région du signal. Ensuite, l'exploitation des cinématiques et/ou topologies différentes du signal et du bruit de fond a permis d'optimiser cette recherche atteignant alors une sensibilité attendue (observée) de 7.8 (6.6) fois le Modèle Standard pour une masse de 165 GeV/c2. Enfin, l'interprétation de l'analyse dans un scénario à quatre familles de fermions a été effectuée. Pour la première fois, cette analyse est incluse dans les combinaisons D0 et Tevatron présentées à Moriond EW et EPS 2011. / The gauge symmetry is the heart of our understanding of the electroweak interaction and describes all the current experimental results. However, the intrinsic incompatibility between the gauge invariance and the mass of particles leads to the introduction of a new particle, the Higgs boson, for which we have no experimental evidence as of today. This thesis describes the Higgs boson search in the mu+tau final state in 7.3/fb of protons-antiprotons collisions at sqrt{s} = 1.96 TeV collected by the D0 detector at the Tevatron. This analysis completes the golden channels (dimuons, electron-muon, dielectrons) exploiting the decay chain H-> WW ->lvlv, which is the main Higgs boson decay mode in the mass window accessible to the Tevatron. Since the final state includes a tau lepton, work was done to improve their identification among jets. An increase of 15% was achieved thanks to the the following : changing tuning parameters for the tau identification neural network, use of the kinematical dependence of the algorithm performances, incorporation of the tau lepton life time information and full study of the additionnal information coming from the central preshower measurements. Then, since the dominant background of the mu+tau Higgs boson search is W+jets (where one jet fakes a tau), a method was developed to obtain good modeling of this background, not provided by the default simulation. This method is based, among other things, on the charge correlation between the muon and the tau candidate which allows for calibration of this background in the data excluding the signal region. Finally, all the kinematic and/or topological differences between the signal and the background were exploited to optimize this search, reaching an (observed) expected sensitivity of 7.8 (6.6) times the Standard Model for mH = 165 GeV/c2. In addition, this result was also interpreted in a fourth fermion generation scenario. For the first time, this analysis is included in the D0 and Tevatron combinations, both presented at Moriond EW and EPS 2011.

Cette thèse a pour sujet la mesure de la section efficace de production de paires de quarks top-antitop dans l’expérience CMS auprès du LHC. L’état final considéré est le canal semi-leptonique ”tau+jets”. Un boson W issu de la désintégration du quark top se désintègre en un tau hadronique et neutrino tandis que le second boson W se désintègre en une paire quark-antiquark. La conduite de cette analyse a nécessité le développement d’un nouveau mode de déclenchement des données (trigger) incluant la présence de quatre jets dont un identifié en tant que tau hadronique. La configuration de ce trigger ainsi que son efficacité ont été étudiés dans cette thèse. Un échantillon de données correspondant à 3.9 fb−1 a été enregistré avec ce trigger et analysé. Les leptons taus ont été reconstruits grâce à un algorithme identifiant leurs résonances intermédiaires tandis que les jets de quarks beaux issus de la désintégration des quarks tops ont été identifiés grâce à l’algorithme ”probabilité par jet”. Cet algorithme pour lequel j’ai mis en oeuvre une procédure de calibration depuis 2009 utilise le paramètre d’impact des traces de particules chargées pour calculer leur probabilité de venir du vertex primaire. Des études de performance de cet algorithme sont également présentées dans cette thèse. Afin de séparer le signal de l’important bruit de fond majoritairement constitué des processus multijets QCD et W+jets un réseau de neurones utilisant des variables dites d’environnement (aplanarité, HT, M(τ,jets), énergie transverse manquante...) a été développé. La section efficace a été extraite à l’aide d’un ajustement par méthode du maximum de vraisemblance de la sortie du réseau de neurones. Les incertitudes systématiques ont fait l’objet d’une étude détaillée. La valeur de la section efficace mesurée, σ(top-antitop) = 156 ± 12 (stat.) ± 33 (syst.) ± 3 (lumi) pb, est en accord avec la section efficace prédite par le modèle standard. / In this thesis we present the first measurement in the CMS experiment of the top-antitop production cross section in the tau+jets final state. To perform this measurement we designed a specific trigger requiring the presence of four jets, one of them being identified as an hadronic tau. The performance of this trigger has been studied in this thesis. A dataset of 3.9 fb-1 was collected with this trigger and analyzed. At offline level we needed to apply a sophisticated tau identification technique to identify the tau jets, based on the reconstruction of the intermediate resonances of the hadronic tau decay modes. Another crucial point was the b-jet identification, both to identify the b-jets in the final state and to modelize the background using a data driven technique. The studies done on the b-tag algorithms along the PhD period are also presented with particular attention to the ”Jet Probability” algorithm. It is the algorithm for which I performed the calibration since 2009 as well as the one used to tag the b-jets from the top decays. A neural network has been developed to separate the top-antitop events from the W+jets and multijet backgrounds. A binned likelihood fit to the neural network output distribution is done in order to extract the signal contribution from the background. A detailed estimation of the systematic uncertainties on the cross section measurement is also presented. The result for the cross section measurement, σ(tt) = 156 ± 12 (stat.) ± 33 (syst.) ± 3 (lumi) pb, is in perfect agreement with the standard model expectation.