The concept of percolated perpendicular media (PPM) for magnetic data storage is expected to surpass the areal storage density of 1 Tbit in -², which is regarded as the fundamental limit of conventional granular CoCrPt:oxide based recording media. PPM consist of a continuous ferromagnetic thin film with densely distributed defects acting as pinning sites for magnetic domain walls. In this study, practical realizations of PPM were fabricated by the deposition of [Co/Pt]8 multilayers with perpendicular magnetic anisotropy onto nanoperforated templates with various perforation diameters and periods. The structural defects given by the templates serve as pinning sites for the magnetic domain walls within the [Co/Pt]8 multilayers. Magnetometry at both the integral and the local level was employed to investigate the influence of the template on the magnetization reversal and the domain wall pinning. It was found, that magnetic domains can be pinned at the ultimate limit, between three adjacent pinning sites. The coercivity and the depinning field, which both are a measure for the strength of the magnetic domain wall pinning, were found to increase with increasing perforation diameter. The size of magnetic domains within the magnetic film appeared not to depend solely on the diameter of the nanoperforations or on the period of the template, but on the ration between diameter and period. By means of micromagnetic simulations it was found, that the presence of ferromagnetic material within the pinning site given supports the pinning of magnetic domain walls, compared to a pinning site that is solely given by a hole in the magnetic thin film. Investigation of the evolution of the magnetization in magnetic fields smaller than the coercive field revealed, that the energy barrier against thermally induced magnetization reversal is sufficiently large to provide long-term (> 10 years) stability of an arbitrary magnetization state. This could also be qualitatively supported by micromagnetic simulations. Static read/write tests with conventional hard disk recording heads revealed the possibility of imprinting bit patterns into the PPM under study. The minimum bit pitch that could be read back thereby depended on the period of the nanoperforated template.

The increasing demand for nearline storage capacity in data centers calls for a continued enhancement in hard disk drive recording density far beyond one terabit per square inch. The thermal stability limit forces the drive manufacturers to develop new concepts in order to achieve this in the long term. Potential solutions are microwave-assisted magnetic recording (MAMR), heat-assisted magnetic recording (HAMR) and bit-patterned media (BPM). A simple example of BPM based on sputter-deposited Co/Pd multilayers and prepatterned substrates at hypothetical recording densities up to one terabit per square inch was studied by magnetic force microscopy (MFM). This system achieved promising results at lower densities, but an actual application for data storage, especially at one terabit per square inch and higher densities, requires elaborate optimizations. For some time now, FePt thin films have attracted much attention as prospective recording layers for high-density magnetic data storage due to their high magnetic anisotropy. The use of FePt films in HAMR is especially promising. This application has been tested successfully by Seagate and its key customers in recent years and is about to be introduced into the nearline hard disk drive market. It requires a tuning of the magnetic properties of FePt, especially of its Curie temperature. The addition of Cu proved to be effective in this regard and can also facilitate the formation of the crucial L10 structure and (001) texture during rapid thermal annealing of sputter-deposited thin films. Such films were prepared as bilayers of Cu and FePt on Si substrates, annealed for 30 s, and analyzed by X-ray diffraction (XRD) and SQUID vibrating sample magnetometry (SQUID-VSM). The influence of large Cu additions on important properties like lattice parameters, mosaicity, magnetic anisotropy and Curie temperature is discussed. The chemical long-range order was calculated from the XRD data, and a dedicated chapter of this thesis covers the most important factors to be considered in such calculations for textured thin films and other samples. The feasibility of creating patterned Fe-Cu-Pt films with perpendicular magnetic anisotropy, as needed for a combination of HAMR and BPM, by deposition through a PMMA mask, a lift-off process and subsequent annealing was investigated as well. The results indicate that the chosen approach might not lead to the required (001) texture when the nanostructures are small enough to compete with today's recording densities, so that either a continuous film might need to be etched after annealing or a seed layer might be required to induce the texture.:1. Motivation: Magnetic Data Storage 2. Experimental Techniques 3. Co/Pd Multilayers on Prepatterned Substrates 4. Fe-Pt and Fe-Cu-Pt Alloys 5. Rapid Thermal Annealing of FePt and FePt/Cu Films 6. Order Parameter Calculation 7. Summary