The current requirements in automotive lubrication impose complex formulation. Among all the additives present in oil, the presence of molybdenum dithiocarbamate and zinc dithiophosphate, both tribological additives containing sulfur and phosphorous is found. For environmental reasons, it is important to reduce or eliminate the presence of these two elements contained in oil. Organic molecules based on carbon, oxygen and hydrogen seems to be good candidate. The lubrication mechanism of fatty acids (e.g. stearic, oleic and linoleic acids) is revisited with a new approach combining experimental and computational chemistry studies. First, the adsorption mechanisms of fatty acids on iron-based surfaces are investigated by Ultra-Accelerated Quantum Chemistry Molecular Dynamics simulations. The adsorption of fatty acids on iron oxide surface occurred through the acid group. Depending on the nature of the substrate, on the density of the film and on the tilt angle between the molecule and the surface, different adsorption mechanisms (physisorption and chemisorption) can occur. Stearic acid molecules form a close-packed and well-arranged monolayer whereas unsaturation acids cannot because of steric effects induced by double carbon-carbon bonds. The friction process favors the formation of carboxylate function. Results are confirmed by surface analysis (XPS and PM-IRRAS). Tribological properties of pure fatty acids, blended in PAO 4 and mixture of saturated/unsaturated acids are studied by MD simulations and tribotests. Low friction coefficient with no visible wear is reported for pure stearic acid and single stearic acid blended in PAO 4 at 1%w at high temperature. This lubricating behavior is inhibited in the presence of unsaturated acids, especially at 150 °C. MD simulation results show a faster diffusion toward the surface for unsaturated fatty acids than for stearic acid at all studied temperature.

Les exigences actuelles en terme de lubrification automobile imposent des formulations extrêmement complexes. Parmi tous les additifs présents dans l’huile, on peut noter le dithiocarbamate de molybdène et le dithiophosphate de zinc, additifs à action tribologique à base de soufre et de phosphore. Pour des raisons environnementales, il est important de diminuer voir d’éliminer la présence de ces deux éléments dans les huiles. Les molécules organiques à base de carbone, oxygène et hydrogène semblent être de bons candidats. Le mécanisme de lubrification des acides gras (acides stéarique, oléique et linoléique) est revisité par une approche visant à combiner l’étude expérimentale et la modélisation moléculaire. Tout d’abord, les mécanismes d’adsorption des acides gras sur des surfaces à base de fer sont étudiés par couplage Chimie Quantique et Dynamique Moléculaire (UA-QCMD). L’adsorption des acides gras sur des surfaces à base de fer se fait par la fonction acide. Selon la nature du substrat, la densité du film et l’angle d’inclinaison de la molécule par rapport à la surface, différents mécanismes d’adsorption peuvent avoir lieu (physisorption et chimisorption). Les molécules d’acide stéarique forment une monocouche compacte et bien arrangée alors que les molécules insaturées en sont incapables à cause d’effets stériques induits par les doubles liaisons carbone-carbone. Le frottement favorise la formation de la fonction carboxylate. Ces résultats sont confirmés par des analyses de surface (XPS et PM-IRRAS). Les propriétés tribologiques des acides gras purs, dans la PAO 4 et en mélange dans la PAO 4 sont étudiées par simulation MD et par des tribotests. Un faible frottement et une absence d’usure visible ont été observés pour l’acide stéarique pur et dissous à 1%m dans la PAO 4 à haute température. La présence de molécules insaturées inhibe les propriétés réductrices de frottement de l’acide stéarique, en particulier à 150 °C. Ceci est expliqué par la diffusion des acides gras insaturés bien supérieure à celle de l’acide stéarique dans la PAO 4 à toutes les températures étudiées. / The current requirements in automotive lubrication impose complex formulation. Among all the additives present in oil, the presence of molybdenum dithiocarbamate and zinc dithiophosphate, both tribological additives containing sulfur and phosphorous is found. For environmental reasons, it is important to reduce or eliminate the presence of these two elements contained in oil. Organic molecules based on carbon, oxygen and hydrogen seems to be good candidate. The lubrication mechanism of fatty acids (e.g. stearic, oleic and linoleic acids) is revisited with a new approach combining experimental and computational chemistry studies. First, the adsorption mechanisms of fatty acids on iron-based surfaces are investigated by Ultra-Accelerated Quantum Chemistry Molecular Dynamics simulations. The adsorption of fatty acids on iron oxide surface occurred through the acid group. Depending on the nature of the substrate, on the density of the film and on the tilt angle between the molecule and the surface, different adsorption mechanisms (physisorption and chemisorption) can occur. Stearic acid molecules form a close-packed and well-arranged monolayer whereas unsaturation acids cannot because of steric effects induced by double carbon-carbon bonds. The friction process favors the formation of carboxylate function. Results are confirmed by surface analysis (XPS and PM-IRRAS). Tribological properties of pure fatty acids, blended in PAO 4 and mixture of saturated/unsaturated acids are studied by MD simulations and tribotests. Low friction coefficient with no visible wear is reported for pure stearic acid and single stearic acid blended in PAO 4 at 1%w at high temperature. This lubricating behavior is inhibited in the presence of unsaturated acids, especially at 150 °C. MD simulation results show a faster diffusion toward the surface for unsaturated fatty acids than for stearic acid at all studied temperature.