Oxy-fuel combustion technology, which is based on burning coal in a mixture of oxygen and recycled flue gas (RFG), is suggested as one of new promising technologies for capturing CO2 from power plants. In this thesis study, the pyrolysis and combustion behaviour of various fuels including imported coal, petroleum coke, two different types of indigenous lignites, olive residue and their blends with different proportions in air and oxy-fuel conditions were investigated by using non-isothermal thermogravimetric method (TGA) coupled with Fourier-transform infrared (FTIR) spectrometer. Pyrolysis tests were carried out in nitrogen and carbon dioxide environments, which are the main diluting gases of air and oxy-fuel environment, respectively. Pyrolysis results reveal that weight loss profiles are similar up to high temperature zone in both pyrolysis environments, indicating that CO2 behaves as an inert gas in this temperature range. However, further weight loss takes place in CO2 atmosphere v after 700oC due to CO2-char gasification reaction which is observed in pyrolysis of all fuel samples. Combustion experiments were carried out in four different atmospheres / air, oxygen-enriched air environment (30 % O2 &ndash / 70 % N2), oxy-fuel environment (21 % O2 &ndash / 79 % CO2) and oxygen-enriched oxy-fuel environment (30 % O2 &ndash / 70 % CO2). Combustion experiments show that replacing nitrogen in the gas mixture by the same concentration of CO2 does not affect the combustion process significantly but leads to slight delay (lower weight loss rate and higher burnout temperature) in combustion. Overall comparison of weight loss profiles shows that higher oxygen content in the combustion environment is the dominant factor affecting the combustion rather than the diluting gas. As O2 concentration increases profiles shift through lower temperature zone, peak and burnout temperatures decrease, weight loss rate increases and complete combustion is achieved at lower temperatures and shorter times. Pyrolysis and combustion behaviour of three different fuel blends were also investigated. Results reveal synergistic interactions in combustion tests of all blends in all combustion environments. During pyrolysis and combustion tests gaseous products CO2, CO, H2O, CH4, SO2 and COS were identified in flue gas and analyzed by using FTIR. Results indicate that higher CO and COS formation take place during pyrolysis tests due to gasification reaction in CO2 atmosphere at high temperature zone. Gaseous species evolution trends in combustion tests are found specific for each fuel. However, evolution trends slightly shift to lower temperatures in oxygen-enriched conditions.

Carbon capture and storage technologies are necessary to start lowering greenhouse gas emissions while continuing to utilize existing thermal power generation infrastructure. Calcium looping is a promising technology based on cyclic calcination/carbonation reactions which utilizes limestone as a sorbent. Steam is present in combustion flue gas and in the calciner used for sorbent regeneration. The effect of steam during calcination on sorbent performance has not been extensively studied in the literature. Here, experiments were conducted using a thermogravimetric analyzer (TGA) and subsequently a dual-fluidized bed pilot plant to determine the effect of steam injection during calcination on sorbent reactivity during carbonation. In a TGA, various levels of steam (0-40% vol.) were injected during sorbent regeneration throughout 15 calcination/carbonation cycles. All concentrations of steam were found to increase sorbent reactivity during carbonation. A level of 15% steam during calcination had the largest impact. Steam changes the morphology of the sorbent during calcination, likely by shifting the pore volume to larger pores, resulting in a structure which has an increased carrying capacity. This effect was then examined at the pilot scale to determine if the phase contacting patterns and solids heat-up rates in a fluidized bed were factors. Three levels of steam (0%, 15%, 65%) were injected during sorbent regeneration throughout 5 hours of steady state operation. Again, all levels of steam were found to increase sorbent reactivity and reduce the required sorbent make-up rate with the best performance seen at 65% steam.

Um novo laboratório experimental desenvolvido para investigar a combustão de carvão em atmosferas de oxicombustão é descrito em detalhes na tese. Um reator ciclônico é utilizado para a combustão de carvões de baixo rank em condições de escoamento turbulento e com swirl, e operando em temperaturas similares às encontradas em câmaras de combustão industriais. Um sensor potenciométrico de oxigênio, instalado dentro do reator ciclônico, é utilizado para medir o consumo de oxigênio durante a combustão das amostras de carvão. Amostras de carvão com alto teor de cinzas, das minas do Leão e Bonito localizadas no sul do Brasil, e amostras de carvão linhito pré-seco (LTBK), da região da Lusácia, na Alemanha, foram submetidos à combustão em atmosferas de ar e de oxicombustão (O2/CO2/H2O). Os experimentos foram realizados em três temperaturas médias do gás de combustão: 1073, 1173 e 1273 K. Para as amostras do carvão LTBK, a oxicombustão foi composta com duas atmosferas de O2/CO2 sem vapor d’água (21/79 e 30/70) e três atmosferas de O2/CO2/H2O (30/60/10, 30/50/20 e 30/40/30) em base molar, enquanto para as amostras dos carvões Leão e Bonito, a oxicombustão foi composta com duas atmosferas de O2/CO2 (21/79 e 30/70). As amostras de carvão foram peneiradas para uma faixa de tamanho de partículas de 1250 a 2000 μm e 125 a 500 μm, e com massas de 1g e 3g. Em adição aos testes, amostras de char dos carvões Leão e LTBK foram preparadas para investigar o comportamento da combustão de suas matrizes carbonosas com diferentes níveis de matéria volátil. Primeiramente, a investigação da combustão do carvão é feita diretamente a partir das curvas de concentração de oxigênio medidas para a combustão das amostras de carvão LTBK submetidos às atmosferas de ar e oxicombustão com vapor d’água, conforme explicado no Capítulo 2 desta tese. Entretanto, devido ao grande número de experimentos realizados e a necessidade de entender a influência dos fatores, como temperatura e as composições das atmosferas oxidantes, e as interações entre esses fatores na combustão do carvão, a análise pela metodologia do Projeto de Experimentos (DoE) é aplicada nos experimentos, conforme detalhado no Capítulo 3. A reatividade dos carvões de baixo rank é investigada por meio do cálculo dos parâmetros cinéticos globais e dos coeficientes da taxa de reação de combustão do char, considerando a hipótese de um reator bem misturado, a ser verificada ao longo da investigação, conforme descrito no Capítulo 4. A partir da análise das curvas de concentração de oxigênio (Capítulos 2 e 3), os resultados mostram que a atmosfera de oxicombustão com 79% de CO2 (21/79, O2/CO2) aumenta o consumo de oxigênio para os carvões de alto teor de cinzas, Bonito e Leão, e para o carvão linhito com alto teor de voláteis (LTBK), devido à influência da reação de gaseificação do CO2 a partir de temperaturas acima de 1073 K. A partir da análise dos parâmetros cinéticos globais calculados para avaliar a reatividade dos carvões, os resultados mostram que a hipótese do reator bem misturado não é o suficiente para capturar a cinética da combustão do carvão por batelada no interior do reator ciclônico. A reatividade dos carvões investigados, através das constantes efetivas da taxa de reação, variando-se a composição da atmosfera oxidante, temperatura do gás de combustão, tamanho de partículas, massa da amostra e posição do sensor de oxigênio, têm influência do escoamento com swirl e seus termos advectivos e difusivos. / A novel laboratory facility designed to investigate coal oxy-fuel combustion is described in the present work. A cyclone chamber allows for the combustion of low-rank coal under turbulent conditions and swirling flows, covering a temperature range similar to those found on practical furnaces. A potentiometric oxygen sensor with oxide-ion conducting solid electrolytes, as stabilized zirconia, installed within the cyclone reactor, is used to measure the oxygen consumption during the combustion of coal samples. High ash coals samples, from Leão and Bonito mining sites located in South Brazil, and pre-dried lignite coal samples (LTBK), from the Lusatian region, in Germany, were burned under air and oxy-fuel (O2/CO2/H2O) atmospheres. Experiments were carried out at three average gas combustion temperatures: 1073, 1173 and 1273 K. For LTBK coal, oxy-fuel combustion was composed with two O2/CO2 atmospheres (21/79 and 30/70) and three O2/CO2/H2O atmospheres (30/60/10, 30/50/20 and 30/40/30) in molar basis, whereas for Leão and Bonito coals, the oxy-fuel combustion was composed with two O2/CO2 atmospheres (21/79 and 30/70). Coal samples were sieved to a size range of 1250 to 2000 μm and 125 to 500 μm and with 1g and 3g. In addition, char samples from Leão and lignite coals were prepared in order to investigate the combustion behavior of its carbon matrix for different levels of volatile matter. The investigation of coal combustion behavior is made firstly directly on the oxygen concentration curves measured for LTBK coal samples burned under air and oxy-fuel atmospheres with water vapor, as detailed in Chapter 2 of this thesis. However, due to the great number of experiments performed and the need to understand the influence of the factors, as temperature and atmosphere compositions, and the interactions between them on the coal combustion, the Design of Experiments (DoE) analysis is applied in the laboratory test facility, as developed in Chapter 3. The reactivity of low rank coals is assessed by means of global kinetic parameters and of char combustion reaction coefficients, under assumption of a well stirred reactor to be tested along the investigation, as described in Chapter 4. From the analysis of oxygen concentration curves (Chapter 2 and 3), results show that oxidizer oxy-fuel atmosphere with 79% CO2 (21/79, O2/CO2) increases the oxygen consumption for high ash coals, Bonito and Leão, and for pre-dried lignite coal, LTBK, due to the influence of CO2 gasification reaction on their coal combustion reactions from gas combustion temperatures higher than 1073 K. From the analysis of global kinetic parameters calculated to assess the coal reactivity, the results show that the hypothesis of a well stirred reactor is not enough to capture the kinetic involved in coal combustion burned in batch mode within the cyclone reactor. The coal reactivity investigated with the effective reaction rate constants for different oxidizer atmospheres, gas combustion temperatures, particle diameters, sample masses and oxygen sensor position, is influenced by the swirling flow with its advective and diffusive terms.

Um novo laboratório experimental desenvolvido para investigar a combustão de carvão em atmosferas de oxicombustão é descrito em detalhes na tese. Um reator ciclônico é utilizado para a combustão de carvões de baixo rank em condições de escoamento turbulento e com swirl, e operando em temperaturas similares às encontradas em câmaras de combustão industriais. Um sensor potenciométrico de oxigênio, instalado dentro do reator ciclônico, é utilizado para medir o consumo de oxigênio durante a combustão das amostras de carvão. Amostras de carvão com alto teor de cinzas, das minas do Leão e Bonito localizadas no sul do Brasil, e amostras de carvão linhito pré-seco (LTBK), da região da Lusácia, na Alemanha, foram submetidos à combustão em atmosferas de ar e de oxicombustão (O2/CO2/H2O). Os experimentos foram realizados em três temperaturas médias do gás de combustão: 1073, 1173 e 1273 K. Para as amostras do carvão LTBK, a oxicombustão foi composta com duas atmosferas de O2/CO2 sem vapor d’água (21/79 e 30/70) e três atmosferas de O2/CO2/H2O (30/60/10, 30/50/20 e 30/40/30) em base molar, enquanto para as amostras dos carvões Leão e Bonito, a oxicombustão foi composta com duas atmosferas de O2/CO2 (21/79 e 30/70). As amostras de carvão foram peneiradas para uma faixa de tamanho de partículas de 1250 a 2000 μm e 125 a 500 μm, e com massas de 1g e 3g. Em adição aos testes, amostras de char dos carvões Leão e LTBK foram preparadas para investigar o comportamento da combustão de suas matrizes carbonosas com diferentes níveis de matéria volátil. Primeiramente, a investigação da combustão do carvão é feita diretamente a partir das curvas de concentração de oxigênio medidas para a combustão das amostras de carvão LTBK submetidos às atmosferas de ar e oxicombustão com vapor d’água, conforme explicado no Capítulo 2 desta tese. Entretanto, devido ao grande número de experimentos realizados e a necessidade de entender a influência dos fatores, como temperatura e as composições das atmosferas oxidantes, e as interações entre esses fatores na combustão do carvão, a análise pela metodologia do Projeto de Experimentos (DoE) é aplicada nos experimentos, conforme detalhado no Capítulo 3. A reatividade dos carvões de baixo rank é investigada por meio do cálculo dos parâmetros cinéticos globais e dos coeficientes da taxa de reação de combustão do char, considerando a hipótese de um reator bem misturado, a ser verificada ao longo da investigação, conforme descrito no Capítulo 4. A partir da análise das curvas de concentração de oxigênio (Capítulos 2 e 3), os resultados mostram que a atmosfera de oxicombustão com 79% de CO2 (21/79, O2/CO2) aumenta o consumo de oxigênio para os carvões de alto teor de cinzas, Bonito e Leão, e para o carvão linhito com alto teor de voláteis (LTBK), devido à influência da reação de gaseificação do CO2 a partir de temperaturas acima de 1073 K. A partir da análise dos parâmetros cinéticos globais calculados para avaliar a reatividade dos carvões, os resultados mostram que a hipótese do reator bem misturado não é o suficiente para capturar a cinética da combustão do carvão por batelada no interior do reator ciclônico. A reatividade dos carvões investigados, através das constantes efetivas da taxa de reação, variando-se a composição da atmosfera oxidante, temperatura do gás de combustão, tamanho de partículas, massa da amostra e posição do sensor de oxigênio, têm influência do escoamento com swirl e seus termos advectivos e difusivos. / A novel laboratory facility designed to investigate coal oxy-fuel combustion is described in the present work. A cyclone chamber allows for the combustion of low-rank coal under turbulent conditions and swirling flows, covering a temperature range similar to those found on practical furnaces. A potentiometric oxygen sensor with oxide-ion conducting solid electrolytes, as stabilized zirconia, installed within the cyclone reactor, is used to measure the oxygen consumption during the combustion of coal samples. High ash coals samples, from Leão and Bonito mining sites located in South Brazil, and pre-dried lignite coal samples (LTBK), from the Lusatian region, in Germany, were burned under air and oxy-fuel (O2/CO2/H2O) atmospheres. Experiments were carried out at three average gas combustion temperatures: 1073, 1173 and 1273 K. For LTBK coal, oxy-fuel combustion was composed with two O2/CO2 atmospheres (21/79 and 30/70) and three O2/CO2/H2O atmospheres (30/60/10, 30/50/20 and 30/40/30) in molar basis, whereas for Leão and Bonito coals, the oxy-fuel combustion was composed with two O2/CO2 atmospheres (21/79 and 30/70). Coal samples were sieved to a size range of 1250 to 2000 μm and 125 to 500 μm and with 1g and 3g. In addition, char samples from Leão and lignite coals were prepared in order to investigate the combustion behavior of its carbon matrix for different levels of volatile matter. The investigation of coal combustion behavior is made firstly directly on the oxygen concentration curves measured for LTBK coal samples burned under air and oxy-fuel atmospheres with water vapor, as detailed in Chapter 2 of this thesis. However, due to the great number of experiments performed and the need to understand the influence of the factors, as temperature and atmosphere compositions, and the interactions between them on the coal combustion, the Design of Experiments (DoE) analysis is applied in the laboratory test facility, as developed in Chapter 3. The reactivity of low rank coals is assessed by means of global kinetic parameters and of char combustion reaction coefficients, under assumption of a well stirred reactor to be tested along the investigation, as described in Chapter 4. From the analysis of oxygen concentration curves (Chapter 2 and 3), results show that oxidizer oxy-fuel atmosphere with 79% CO2 (21/79, O2/CO2) increases the oxygen consumption for high ash coals, Bonito and Leão, and for pre-dried lignite coal, LTBK, due to the influence of CO2 gasification reaction on their coal combustion reactions from gas combustion temperatures higher than 1073 K. From the analysis of global kinetic parameters calculated to assess the coal reactivity, the results show that the hypothesis of a well stirred reactor is not enough to capture the kinetic involved in coal combustion burned in batch mode within the cyclone reactor. The coal reactivity investigated with the effective reaction rate constants for different oxidizer atmospheres, gas combustion temperatures, particle diameters, sample masses and oxygen sensor position, is influenced by the swirling flow with its advective and diffusive terms.

Um novo laboratório experimental desenvolvido para investigar a combustão de carvão em atmosferas de oxicombustão é descrito em detalhes na tese. Um reator ciclônico é utilizado para a combustão de carvões de baixo rank em condições de escoamento turbulento e com swirl, e operando em temperaturas similares às encontradas em câmaras de combustão industriais. Um sensor potenciométrico de oxigênio, instalado dentro do reator ciclônico, é utilizado para medir o consumo de oxigênio durante a combustão das amostras de carvão. Amostras de carvão com alto teor de cinzas, das minas do Leão e Bonito localizadas no sul do Brasil, e amostras de carvão linhito pré-seco (LTBK), da região da Lusácia, na Alemanha, foram submetidos à combustão em atmosferas de ar e de oxicombustão (O2/CO2/H2O). Os experimentos foram realizados em três temperaturas médias do gás de combustão: 1073, 1173 e 1273 K. Para as amostras do carvão LTBK, a oxicombustão foi composta com duas atmosferas de O2/CO2 sem vapor d’água (21/79 e 30/70) e três atmosferas de O2/CO2/H2O (30/60/10, 30/50/20 e 30/40/30) em base molar, enquanto para as amostras dos carvões Leão e Bonito, a oxicombustão foi composta com duas atmosferas de O2/CO2 (21/79 e 30/70). As amostras de carvão foram peneiradas para uma faixa de tamanho de partículas de 1250 a 2000 μm e 125 a 500 μm, e com massas de 1g e 3g. Em adição aos testes, amostras de char dos carvões Leão e LTBK foram preparadas para investigar o comportamento da combustão de suas matrizes carbonosas com diferentes níveis de matéria volátil. Primeiramente, a investigação da combustão do carvão é feita diretamente a partir das curvas de concentração de oxigênio medidas para a combustão das amostras de carvão LTBK submetidos às atmosferas de ar e oxicombustão com vapor d’água, conforme explicado no Capítulo 2 desta tese. Entretanto, devido ao grande número de experimentos realizados e a necessidade de entender a influência dos fatores, como temperatura e as composições das atmosferas oxidantes, e as interações entre esses fatores na combustão do carvão, a análise pela metodologia do Projeto de Experimentos (DoE) é aplicada nos experimentos, conforme detalhado no Capítulo 3. A reatividade dos carvões de baixo rank é investigada por meio do cálculo dos parâmetros cinéticos globais e dos coeficientes da taxa de reação de combustão do char, considerando a hipótese de um reator bem misturado, a ser verificada ao longo da investigação, conforme descrito no Capítulo 4. A partir da análise das curvas de concentração de oxigênio (Capítulos 2 e 3), os resultados mostram que a atmosfera de oxicombustão com 79% de CO2 (21/79, O2/CO2) aumenta o consumo de oxigênio para os carvões de alto teor de cinzas, Bonito e Leão, e para o carvão linhito com alto teor de voláteis (LTBK), devido à influência da reação de gaseificação do CO2 a partir de temperaturas acima de 1073 K. A partir da análise dos parâmetros cinéticos globais calculados para avaliar a reatividade dos carvões, os resultados mostram que a hipótese do reator bem misturado não é o suficiente para capturar a cinética da combustão do carvão por batelada no interior do reator ciclônico. A reatividade dos carvões investigados, através das constantes efetivas da taxa de reação, variando-se a composição da atmosfera oxidante, temperatura do gás de combustão, tamanho de partículas, massa da amostra e posição do sensor de oxigênio, têm influência do escoamento com swirl e seus termos advectivos e difusivos. / A novel laboratory facility designed to investigate coal oxy-fuel combustion is described in the present work. A cyclone chamber allows for the combustion of low-rank coal under turbulent conditions and swirling flows, covering a temperature range similar to those found on practical furnaces. A potentiometric oxygen sensor with oxide-ion conducting solid electrolytes, as stabilized zirconia, installed within the cyclone reactor, is used to measure the oxygen consumption during the combustion of coal samples. High ash coals samples, from Leão and Bonito mining sites located in South Brazil, and pre-dried lignite coal samples (LTBK), from the Lusatian region, in Germany, were burned under air and oxy-fuel (O2/CO2/H2O) atmospheres. Experiments were carried out at three average gas combustion temperatures: 1073, 1173 and 1273 K. For LTBK coal, oxy-fuel combustion was composed with two O2/CO2 atmospheres (21/79 and 30/70) and three O2/CO2/H2O atmospheres (30/60/10, 30/50/20 and 30/40/30) in molar basis, whereas for Leão and Bonito coals, the oxy-fuel combustion was composed with two O2/CO2 atmospheres (21/79 and 30/70). Coal samples were sieved to a size range of 1250 to 2000 μm and 125 to 500 μm and with 1g and 3g. In addition, char samples from Leão and lignite coals were prepared in order to investigate the combustion behavior of its carbon matrix for different levels of volatile matter. The investigation of coal combustion behavior is made firstly directly on the oxygen concentration curves measured for LTBK coal samples burned under air and oxy-fuel atmospheres with water vapor, as detailed in Chapter 2 of this thesis. However, due to the great number of experiments performed and the need to understand the influence of the factors, as temperature and atmosphere compositions, and the interactions between them on the coal combustion, the Design of Experiments (DoE) analysis is applied in the laboratory test facility, as developed in Chapter 3. The reactivity of low rank coals is assessed by means of global kinetic parameters and of char combustion reaction coefficients, under assumption of a well stirred reactor to be tested along the investigation, as described in Chapter 4. From the analysis of oxygen concentration curves (Chapter 2 and 3), results show that oxidizer oxy-fuel atmosphere with 79% CO2 (21/79, O2/CO2) increases the oxygen consumption for high ash coals, Bonito and Leão, and for pre-dried lignite coal, LTBK, due to the influence of CO2 gasification reaction on their coal combustion reactions from gas combustion temperatures higher than 1073 K. From the analysis of global kinetic parameters calculated to assess the coal reactivity, the results show that the hypothesis of a well stirred reactor is not enough to capture the kinetic involved in coal combustion burned in batch mode within the cyclone reactor. The coal reactivity investigated with the effective reaction rate constants for different oxidizer atmospheres, gas combustion temperatures, particle diameters, sample masses and oxygen sensor position, is influenced by the swirling flow with its advective and diffusive terms.

Carbon capture and storage technologies are necessary to start lowering greenhouse gas emissions while continuing to utilize existing thermal power generation infrastructure. Calcium looping is a promising technology based on cyclic calcination/carbonation reactions which utilizes limestone as a sorbent. Steam is present in combustion flue gas and in the calciner used for sorbent regeneration. The effect of steam during calcination on sorbent performance has not been extensively studied in the literature. Here, experiments were conducted using a thermogravimetric analyzer (TGA) and subsequently a dual-fluidized bed pilot plant to determine the effect of steam injection during calcination on sorbent reactivity during carbonation. In a TGA, various levels of steam (0-40% vol.) were injected during sorbent regeneration throughout 15 calcination/carbonation cycles. All concentrations of steam were found to increase sorbent reactivity during carbonation. A level of 15% steam during calcination had the largest impact. Steam changes the morphology of the sorbent during calcination, likely by shifting the pore volume to larger pores, resulting in a structure which has an increased carrying capacity. This effect was then examined at the pilot scale to determine if the phase contacting patterns and solids heat-up rates in a fluidized bed were factors. Three levels of steam (0%, 15%, 65%) were injected during sorbent regeneration throughout 5 hours of steady state operation. Again, all levels of steam were found to increase sorbent reactivity and reduce the required sorbent make-up rate with the best performance seen at 65% steam.

Diplomová práce se zabývá spalováním zemního plynu při využití vzduchu s vyšším obsahem kyslíku (21–46 % kyslíku ve spalovacím vzduchu), tzv. kyslíkem obohaceným spalováním (OEC). Technologie OEC nalezla uplatnění v průmyslu, kde se jsou nároky na zvýšenou produktivitu, dosažení vyšší tepelné účinnosti, zlepšení vlastností plamene, snížení náklady, či zlepšení kvality výsledného produktu. Ačkoliv OEC přináší řadu výhod, je nutné zmínit i nevýhody jako: poškození zařízení, nestejnoměrné zahřívání, narušení plamene, zvýšené emise anebo zpětný zášleh plamene. Zkoušky proběhly na zkušebně hořáků, která umožňuje testovat hořáky nejen na plynná a kapalná paliva, ale i hořáky navržené pro kombinované spalování při maximálním výkonu hořáku 1 800 kW. Při zkouškách byl použit plynový „low-NOx“ hořák se stupňovitým přívodem paliva. V diplomové práci je popsán vliv obsahu kyslíku ve spalovacím vzduchu na emise oxidů dusíku (NOx), teplotu plamene, přenos tepla ze spalin do stěn spalovací komory, a také vlastnosti plamene, zvláště pak jeho stabilitu, tvar a rozměry. Zkoušky proběhly při výkonech 300 kW, 500 kW a 750 kW, přičemž pro výkon 750 kW proběhly testy jak při jednostupňové, tak dvoustupňové konfiguraci.

Die Herleitung des Unterschieds zwischen globaler und lokaler Stöchiometriezahl für den Oxyfuel-Prozess hat gezeigt, dass gleiche lokale Stöchiometriezahlen bei variierendem Rezirkulationsanteil unterschiedliche globale Stöchiometriezahlen zur Folge haben. In dieser Arbeit wird vorgeschlagen, die Bezeichnung der Zustandspunkte im Oxyfuel-Prozess mit den Sauerstoffkonzentrationen am Brennkammereintritt bzw. -austritt zu verbinden. Für den Sauerstoffanteil am Brennkammereintritt (z.B. 30 vol.-%) und den Restsauerstoff am Brennkammerende (z.B. 4 vol.-%) folgt zum Bespiel die Bezeichnung Oxyfuel 30 mit 4 % Restsauerstoff. Diese Bezeichnung ist eindeutig und kann das Lambda – als Beschreibung der Stöchiometrie im konventionellen Betrieb – ablösen. Für eine Vielzahl an Punkten sind Verbrennungsversuche mit Trockenbraunkohle und Sauerstoff durchgeführt worden. Ein stabiler Betrieb der Versuchsanlage der TU Dresden wurde zwischen Oxyfuel 17 und Oxyfuel 33 erreicht. Die Untersuchungen haben nachgewiesen, dass die Rezirkulation des feuchten Abgases für die Verbrennung unkritisch ist. Die Schwefeldioxid-Emissionen sind abhängig von den variierenden Reaktionstemperaturen im Kennfeld, dem Restsauerstoff am Brennkammerende und der Rezirkulation des Abgases. Mit der Belagssondenmessung von Aschepartikeln im Abgasstrom wurde gezeigt, dass auch andere Komponenten (z.B. Chlor) im Oxyfuel-Prozess aufkonzentriert werden. Diese erhöhten Konzentrationen werden zu neuen Anforderungen in der Werkstoffauswahl führen. Für das Einschwingverhalten der Abgaszusammensetzung beim Umschalten von konventioneller Verbrennung zu Oxyfuel-Prozess-Fahrweise hat sich gezeigt, dass für diese Staubfeuerungs-Versuchsanlage ein einfaches Rührkesselmodell geeignet ist.

Coal ash deposits were collected in a 160 kWth, down-fired oxy-coal reactor under staged and unstaged conditions for four different coals (PRB, Gatling, Illinois #6, and Mahoning). Concentration measurements of carbon, oxygen, sodium, magnesium, aluminum, silicon, phosphorus, sulfur, chlorine, potassium, calcium, titanium, chromium, manganese, iron, nickel, strontium, and barium were gathered from each deposit sample using scanning electron microscopy and energy dispersive spectroscopy (SEM-EDS). Backscattered electron micrographs for each deposit sample were analyzed to gather morphological data. Particle size and shape were studied for each deposit collected. The average particle sizes of the particles in upstream deposits were much larger than the average particle sizes of the downstream deposits. The downstream deposits consisted primarily of spherical particles while the upstream deposits consisted of round, irregular polygonal, and porous particles. Deposit particles are believed to have deposited at all stages of burnout; those depositing early during pyrolysis may have continued to react after deposition. Element maps for the aforementioned elements were collected with SEM-EDS and analyzed to quantify both average composition and composition of individual particles. These values were compared to ASTM ash analyses performed for each coal and ash collected from the flue gas stream with a cyclonic particle separator. It was found that sulfur concentrations of deposits do not correlate with corresponding sulfur concentrations of the coal. Comparison of similar experiments performed with air-combustion show that oxy-combustion deposits contain about twice as much sulfur as air-combustion deposits when burning the same coal. Deposition propensity of each coal was also examined, and the PRB and Gatling coals were found to have a moderately high deposition propensity whereas the deposition propensity of the Mahoning and Illinois #6 coals was fairly low.

No description available.