Fluorinated polymers are niche macromolecules that play an essential role in modern life. The special properties of fluorine, including among others, a large electronegativity (ca 3.98), low polarisability, small van der Waal’s radius (135 pm) and the strong C-F bond (ca 485 kJ · mol−1), impart unique properties to organofluorine compounds. Flu-oropolymers exhibit a combination of desirable traits, including high thermal stability, low coefficient of friction, chemical inertness, oleo- and hydrophobicity, and low surface tension. Among the fluoropolymers, polyvinylidene fluoride (PVDF), and copolymers of vinylidene fluoride (VDF) and hexafluoropropylene (HFP), have found applications in the coatings industry as the binder in exterior coatings. The chemical inertness of poly(VDF-co-HFP) copolymer, however, prevents disper-sion of pigments into the coating and also inhibits adhesion of the coating onto substrates. An acrylic modifier polymer is typically added to the poly(VDF-co-HFP) copolymer to improve the dispersion of pigments and the adhesion of the coating. This acrylic copoly-mer is physically blended with the poly(VDF-co-HFP) copolymer on a macromolecular scale (i.e. it forms a thermodynamically miscible blend). The loading of acrylic copolymer in commercial PVDF coatings is often in the range of 20 to 30 % by weight of polymer solids. Typically, copolymers of methyl methacrylate, ethyl acrylate and methacrylic esters are employed. Alternative strategies to overcome the adhesion problem include, among others, chem-ical modification of the surface of the fluoropolymer film. This can be achieved by graft copolymerisation or core shell emulsion polymerisation. These methods are used to funcionalise the polymer chains, while maintaining the desirable properties of the parent polymer. Due to environmental regulations, industry focus has shifted towards develop-ing coatings with a low volatile organic compound (VOC) content. Aqueous, low VOC, air-drying coatings can be formulated directly from the acrylic modified fluoropolymer (AMF) latex and have superior properties to solvent based, high VOC, air-dry coatings. Their advantages include low viscosities, reduced flammability, reduced odour and easy application using conventional equipment. A large portion of the aqueous coatings are sold into the architectural market with over 70 % of architectural paints used in the United States being classified as aqueous. Arkema Inc. has developed a commercial aqueous fluoropolymer latex using the method of seeded emulsion polymerisation. VDF and HFP monomers are randomly copolymerised via emulsion polymerisation. This poly(VDF-co-HFP) copolymer may be used as the seed material in a core-shell polymerisation using acrylic monomers. Kato et al. [49] discloses the preparation of an AMF formulation for poly(VDF-co-HFP) copoly-mer. Preliminary testing of membrane textiles coated with such formulations showed that the AMF coatings degrade under UV irradiation more rapidly than is is expected for poly(VDF-co-HFP) copolymer. The patent indicates that the nature of the product formed by the emulsion polymerisation is not well understood and the product my be either a graft copolymer of a core-shell system. The aim of this research reported in this dissertation was to shed light on the nature of the final product, and to verify the claims made in the above-mentioned patent. Various acrylic monomers were copolymerised via seeded emulsion polymerisation us-ing commercial poly(VDF-co-HFP) copolymer as the seed material. The concentration and the ratios of the monomers were varied according to the formulation guidelines in Kato et al.[49]. ATR-FTIR spectroscopy and19F NMR spectroscopy was used to de-termine the microstructure of the resultant latexes. ATR-FTIR spectra confirmed the presence of C=C and C=O bonds in latexes. This indicates that unreacted acrylic com-ponents are present. The ATR-FTIR spectra of the films indicated the disappearance of the C=C bonds from the latex, which indicates that the monomers are evaporated easily from the latexes during film formation. The 19F NMR spectra confirmed that no modi-fication of the poly(VDF-co-HFP) copolymer backbone took place during the reactions. The particle size distribution graphs showed an increase particle sizes and this suggested that some self polymerisation of the monomer occurred. The viscosity of the latexes were lower compared to the due to the experiments being conducted under dilution. The flow characteristics of the poly(VDF-co-HFP) copolymer was also influenced with some reactions yielding shear thickening latexes as compared to the shear thinning poly(VDF-co-HFP) copolymerc. The reactions also yielded latexes which displayed lower and higher surface tensions than the poly(VDF-co-HFP) copolymer. Therefore, the conclusion may be drawn from this work that core-shell formation occurred during the emulsion copolymerisation, as opposed to grafting of the monomer onto the poly(VDF-co-HFP) copolymer backbone. The claims made in the literature could not be substantiated; in particluar, the reported improvements in film forming ability were not realised. No commercially useful advantage exists for the emulsion copolymerisation of poly(VDF-co-HFP) copolymer with acrylic monomers over the solution blending of poly(VDF-co-HFP) copolymer with acrylic copolymers. / Dissertation (MEng)--University of Pretoria, 2019. / Chemical Engineering / MEng / Unrestricted

Ever since their discovery, Carbon nanotubes (CNTs) have been renowned to be potential candidates for a variety of applications. Nevertheless, the difficulties accompanied with their dispersion and poor solubility in various solvents have hindered CNTs potential applications. As a result, studies have been developed to address the dispersion problem. The solution is in modifying the surfaces of the nanotubes covalently or non-covalently with a desired dispersant. Various materials have been employed for this purpose out of which polymers are the most common. Non-covalent functionalization of CNTs via polymer wrapping represents an attractive method to obtain a stable and homogenous CNTs dispersion. This method is able to change the surface properties of the nanotubes without destroying their intrinsic structure and preserving their properties. This thesis explores and studies the surface modification and solublization of pristine single and multiwalled carbon nanotubes via a simple solution mixing technique through non-covalent interactions of CNTs with various anionic and cationic conjugated polyelectrolytes (CPEs). The work includes studying the interaction of various poly(phenylene ethynylene) electrolytes with MWCNTs and an imidazolium functionalized poly(3-hexylthiophene) with SWCNTs. Our work here focuses on the noncovalent modifications of carbon nanotubes using novel CPEs in order to use these resulting CPE/CNT complexes in various applications. Upon modifying the CNTs with the CPEs, the resulting CPE/CNT complex has been proven to be easily dispersed in various organic and aqueous solution with excellent homogeneity and stability for several months. This complex was then used as a nanofiller and was dispersed in another polymer matrix (poly(methyl methacrylate), PMMA). The PMMA/CPE/CNT composite materials were cast or electrospun depending on their desired application. The presence of the CPE modified CNTs in the polymer matrix has been proven to enhance the composites thermal, mechanical and electrical properties compared to pristine CNTs. Various spectroscopic and microscopic techniques such as UV-vis, fluorescence, TEM, AFM and SEM were used to study and characterize the CPE/CNT complexes. Also, TGA, DSC and DMA were used to study the thermal and mechanical properties of the composite materials. Our current work represents a fundamental study on the non-covalent interactions between CNTs and CPEs on one hand and gives a real life example on the CPE/CNT application in composite materials and electronics.

Tissue engineering is receiving tremendous attention due to the necessity to overcome the limitations related to injured or diseased tissues or organs. It is the perfect combination of cells and biomimetic-engineered materials. With the appropriate biochemical factors, it is possible to develop new effective bio-devices that are capable to improve or replace biological functions. Latest developments in microfabrication methods, employing mostly synthetic biomaterials, allow the production of three-dimensional (3D) scaffolds that are able to direct cell-to-cell interactions and specific cellular functions in order to drive tissue regeneration or cell transplantation. The presented work offers a rapid and efficient method of 3D scaffolds fabrication by using optical lithography and micro-molding techniques. Bioresorbable polymer poly-ε-caprolactone (PCL) was the material used thanks to its high biocompatibility and ability to naturally degrade in tissues. 3D PCL substrates show a particular combination in the designed length scale: cylindrical shaped pillars with 10μm diameter, 10μm height, arranged in a hexagonal lattice with spacing of 20μm were obtained. The sidewalls of the pillars were nanostructured by attributing a 3D architecture to the scaffold. The suitability of these devices as cell culture technology supports was evaluated by plating NIH/3T3 mouse embryonic fibroblasts and human Neural Stem Cells (hNSC) on them. Scanning Electron Microscopy (SEM) analysis was carried out in order to examine the micro- and nano-patterns on the surface of the supports. In addition, after seeding of cells, SEM and immunofluorescence characterization of the fabricated systems were performed to check adhesion, growth and proliferation. It was observed that cells grow and develop healthy on the bio-polymeric devices by giving rise to well-interconnected networks. 3D PCL nano-patterned pillared scaffold therefore may have considerable potential as effective tool for applications in tissue engineering.

Conventionally, adherent cells are cultured in vitro using flat 2D cell culture trays. However the 2D cell culture method is tedious, unreliable and does not replicate the complexity of the 3D dynamic environment of native tissue. Nowadays 3D scaffolds can be used to culture cells. However a number of challenges still exist, including the need for destructive enzymes to release confluent cells. Poly(Nisopropylacrylamide) (PNIPAAm), a temperature responsive polymer, has revolutionised the cell culture fraternity by providing a non-invasive means of harvesting adherent cells, whereby confluent cells can be spontaneously released by simply cooling the cell culture medium and without requiring enzymes. While PNIPAAm monolayer cell culturing is a promising tool for engineering cell sheets, the current technology is largely limited to the use of flat 2D substrates, which lacks structural and organisational cues for cells. The aim of this project was to develop a 3D PNIPAAm scaffold which could be used efficiently for non-invasive 3D culture of adherent cells. This project was divided into three phases: Phase 1 (preliminary phase) involved development and characterisation of cross-linked PNIPAAm hydrogels; Phase 2 involved development and characterisation of PNIPAAm grafted 3D non-woven scaffolds, while Phase 3 focused on showing proof of concept for non-invasive temperature-induced cell culture from the 3D PNIPAAm grafted scaffolds. In Phase 1, PNIPAAm was cross-linked with N,N’-methylene-bis-acrylamide (MBA) using solution free-radical polymerisation to form P(PNIPAAm-co-MBA) hydrogels. A broad cross-link density (i.e. 1.1 - 9.1 Mol% MBA) was investigated, and the effect of using mixed solvents as the co-polymerisation medium. The P(PNIPAAm-co-MBA) gels proved unsuitable as a robust cell culture matrix, due to poor porosity, slow swelling/deswelling and poor mechanical properties. Subsequently, in Phase 2, polypropylene (PP), polyethylene terephthalate (PET), and nylon fibers were processed into highly porous non-woven fabric (NWF) scaffolds using a needle-punching technology. The NWF scaffolds were grafted with PNIPAAm using oxyfluorination-assisted graft polymerisation (OAGP). The OAGP method involved a 2 step process whereby the NWF was first fluorinated (direct fluorination or oxyfluorination) to introduce new functional groups on the fibre surface. The functionalised NWF scaffolds were then graft-polymerised with NIPAAm in an aqueous medium using ammonium persulphate as the initiator. Following oxyfluorination, new functional groups were detected on the surface of the NWF scaffolds, which included C-OH; C=O; CH2-CHF, and CHF-CHF. PP and nylon were both easily modified by oxyfluorination, while PET displayed very little changes to its surface groups. Improved wetting and swelling in water was observed for the oxyfluorinated polymers compared to pure NWF scaffolds. PP NWF showed the highest graft yield followed by nylon and then PET. PNIPAAm graft yield on the PP NWF was ~24 ±6 μg/cm2 on grafted pre-oxyfluorinated NWF when APS was used; which was found to be significantly higher compared to when pre-oxyfluorinated NWF was used without initiator (9 ±6 μg/cm2, p= 1.7x10-7); or when grafting was on pure PP with APS (2 ±0.3 μg/cm2, p = 8.4x10-12). This corresponded to an average PNIPAAm layer thickness of ~220 ±54 nm; 92 ± 60 nm; and 19 ± 3 nm respectively. Scanning electron microscopy (SEM) revealed a rough surface morphology and confinement of the PNIPAAm graft layer to the surface of the fibers when oxyfluorinated NWF scaffolds were used, however when pure NWF scaffolds were used during grafting, homopolymerisation was observed as a loosely bound layer on the NWF surface. The OAGP method did not affect the crystalline phase of bulk PP as was determined by X-ray diffraction (XRD), however, twin-melting thermal peaks were detected from DSC for the oxyfluorinated PP and PP-g-PNIPAAm NWF which possibly indicated crystal defects. Contact angle studies and microcalorimetric DSC showed that the PP-g-PNIPAAm NWF scaffolds exhibited thermoresponsive behaviour. Using the 2,2-Diphenyl-1-1-picrylhydrazyl (DPPH) radical method and electron-spin resonance (ESR), peroxides, as well as trapped long-lived peroxy radicals were identified on the surface of the oxyfluorinated PP NWF, which are believed to be instrumental in initiating graft polymerisation from the NWF. A free radical mechanism which is diffusion controlled was proposed for the OAGP method with initiation via peroxy radicals (RO•), as well as SO4•- and OH• radicals, whereby the latter result from decomposition of APS. In Phase 3 of this study, proof-of-concept is demonstrated for use of the PNIPAAm grafted NWF scaffolds in non-invasive culture of hepatocytes. Studies demonstrated that hepatocyte cells attached onto the 3D PNIPAAm scaffolds and remained viable in culture over long periods. The cells were released spontaneously and non-destructively as 3D multi-cellular constructs by simply cooling the cell culture medium from 37°C to 20°C, without requiring destructive enzymes. The PP-g- PNIPAAm NWF scaffolds performed the best in 3D cell culture. Additionally the CSIR is developing a thermo responsive 3D (T3D) cell culturing device, whereby the 3D thermo responsive NWF scaffolds are used in the bioreactor for cell culture. Temperature-induced cell release was also verified from the 3D Thermo responsive scaffolds in the bioreactor. This technology could lead to significant advances in improving the reliability of the in vitro cell culture model. Please cite as follows: Chetty, AS 2012, Thermoresponsive 3D scaffolds for non-invasive cell culture, PhD thesis, University of Pretoria, Pretoria, viewed yymmdd < http://upetd.up.ac.za/thesis/available/etd-06112013-151344/ > D13/4/713/ag / Thesis (PhD)--University of Pretoria, 2012. / Chemical Engineering / unrestricted

Emulsion polymerizations of vinyl acetate (VAc) were performed by fully or partially replacing poly(vinyl alcohol) (PVA) with renewable materials as protective colloids or by adding renewable materials, as additives or fillers, to the emulsions during or after polymerization. The purpose of the study was to increase the amount of renewable materials in the emulsion. A total of 19 emulsions were synthesized. Different recipes were used for the synthesis. The following renewable materials were studied; hydroxyethyl cellulose (HEC) with different molecular weights, starch and proteins. HEC and starch were used as protective colloids. Proteins were used as additives or fillers. Cross-linking agent A and Cross-linking agent B were used as cross-linking agents. A total of 26 formulations were pressed, either cold or hot. The synthesized emulsions were evaluated with respect to pH, solids content, viscosity, minimum film formation temperature (MFFT), glass transition temperature (Tg), particle size and molecular weight (Mw). The tensile shear strengths of the emulsions were evaluated according to EN 204 and WATT 91. It was possible to fully, or partially, replace PVA as protective colloid with renewable materials. It was also possible to use renewable materials as additives or fillers in the emulsions. The emulsions obtained properties that differed from the reference. Generally, emulsions with HEC as protective colloid showed lower viscosity and slightly higher MFFT, Tg and molecular weight than emulsions with PVA as protective colloid. Larger particle sizes than the reference were obtained for emulsions containing PVA combined with renewable materials. The emulsion with starch as protective colloid exhibited the largest particle size. 10 formulations passed the criteria for D2. The emulsions where PVA was fully or partially replaced with HEC or starch showed a water resistance similar to the reference (around D2). The addition of protein did not decrease the water and heat resistance compared to the reference. Addition of protein after polymerization increased the water resistance (D2) compared to addition during polymerization. Addition of cross-linking agents did not increase the water resistance further. Two formulations passed the criteria for D3. The emulsion in the first formulation had PVA as protective colloid and protein B was added during polymerization. The emulsion in the second formulation had HEC as protective colloid. To both of these emulsions, protein A was added after polymerization, as a filler, combined with Cross-linking agent B as cross-linking agent before hot pressing. The first formulation also showed a good heat resistance (passed the criteria for WATT 91).

PNIPAM (poly(N-Isopropylacrylamide)) is a well-known thermoresponsive polymer. Dissolved in water, it shows a structural change at 32 oC, above which the polymer folds together, and a phase separation occurs. The temperature where the polymer changes structure is known as the LCST (Lower Critical Solution Temperature), and can be modified by adding certain salts to the solution [1]. The mechanism by which the ionic components of the salts affect the LCST is not yet completely understood. The purpose of this master thesis is to study this mechanism. In order to investigate the mechanism, a combination of diffusion NMR and electrophoretic NMR was used, giving the effective charge per molecule which is directly proportional to the grade of association of ions to the polymer. The salts tested were: NaCl, NaClO4, NaSO4, NaI, NaSCN and CaCl2 from which the ClO4-, SCN-, and I- ions, as well as Cl- ions from CaCl2, were found to bind to PNIPAM.

The aim of this study is to perform a baseline energy survey to understand the existing energy demand and usepattern and to verify the feasibility of a small scale poly-generation project supported by renewable sources ofenergy (biogas based) in a rural area of Bangladesh. A poly-generation solution shall provide multiple outputservices of clean gas, electricity and arsenic free water supply. The project requires using animal dung oragricultural waste to produce biogas and electric energy. The study has analyzed the demand of domesticenergy and water of the village named ‘Matipukur’ in the Jessore district in Bangladesh. The study alsoconsidered available biomass feedstock and energy potential surrounding the village area, as well as the socioeconomicstatus of villagers. The case study included a door to door survey to collect relevant information.Three different economic groups in terms of income scale were investigated throughout the study to obtainbetter insight of the energy-water access situation, requirements and related problems in the village. Almost 98% household of this village relies on biomass for energy due to limited access of modern fuel. Thevillage has various biomass potential in the form of animal dung, fuel wood and agricultural waste which can beused for cooking or serve as the basis for other energy carriers. Kerosene is used for lighting. Among thedifferent fuels, dung meets about 44% of the total demand. The contribution of other fuels for domestic use is24% firewood, 22% agricultural waste, and 2% kerosene. The analytical observation found that the annualaverage energy demand of the village is 8.45 GJ per capita. The share of average demand for cooking and3lighting energy is 8.24 GJ per person/year and 0.21 GJ per person/year respectively. The energy consumptionvaries within different income groups. This study has examined the income per capita, family size, education,agricultural land holding per capita, priorities of their annual expenditure etc. which have direct influence onthe fuel consumption pattern of the household. It could be observed that expenses on energy changes as theincome level increases. About awareness of biogas opportunities and willingness to provide feedstock for apoly generation project, the majority of households answered positively, that is, indicating that they wouldcontribute. Educated respondents showed more positive attitude. Regarding changing of traditional cooking,about 95% of the respondents want to change to a more efficient and reliable cooking system to avoid healthand environmental problems associated with indoor biomass cooking. The study has revealed that only cow dung is not enough to produce clean energy according to demand so theco-digestion method is considered to producing biogas from various energy potentials (animal manure &amp;agricultural waste). The poly-generation system could work with the scenario providing electricity and watersupply for the entire household and cooking gas is limited only for 2/3rd household. Rest 1/3rd household fromlow income group then could be supplied with improve cook stove to meet their daily cooking demand and tominimize indoor pollutions. It is observed that, majority of household has expressed their willingness toprovide raw materials for poly-generation plant though they are using. / SIDA funded research project "Biogas based poly generation in Bangladesh"

Adenosine triphosphate (ATP) is the major carrier of chemical energy in cells. The diffusion of ATP in hydrogels, which have a structural resemblance to the natural extracellular matrix, is therefore of great importance to understand many biological processes. In continuation of our recent studies of ATP diffusion in poly(ethylene glycol) diacrylate (PEG-DA) hydrogels by pulsed field gradient nuclear magnetic resonance (PFG-NMR), we present precise diffusion measurements of ATP in aqueous solutions of PEG-DA polymers, which are not cross-linked to a three-dimensional network. The dependence of the ATP diffusion on the polymer volume fraction in the hydrogels, φ, was found to be consistent with the predictions of a modified obstruction model or the free volume theory in combination with the sieving behavior of the polymer chains. The present measurements of ATP diffusion in aqueous solutions of the polymers revealed that the diffusion coefficient is determined by φ only, regardless of whether the polymers are cross-linked or not. These results seem to be inconsistent with the free volume model, according to which voids are formed by a statistical redistribution of surrounding molecules, which is expected to occur more frequently in the case of not cross-linked polymers. The present results indicate that ATP diffusion takes place only in the aqueous regions of the systems, with the volume fraction of the polymers, including a solvating water layer, being blocked for the ATP molecules. The solvating water layer increases the effective volume of the polymers by 66%. This modified obstruction model is most appropriate to correctly describe the ATP diffusion in PEG-DA hydrogels.

Low-poly är en term som används för att beskriva 3D-modeller som består av få polygoner, vilket är de 2D-plan som utgör en 3D-model. Denna rapport försöker ta reda på hur modeller med hög detaljnivå kan göras om till modeller med lägre detaljnivå för att spara in på tid och kostnader. Det skapades fyra 3D-modeller till en studie som med hjälp av enkäter tog reda på hur mycket uppfattningen av en detaljerad kontra mindre detaljerad modell uppfattas av ett antal informanter. Resultatet visar att med hjälp av tidigare dokumentation om karaktärsdesign så går det att skapa effektiva low-poly karaktär som tydligt kan representera den initiala karaktärsdesignen. Low-poly är en relativ term som innefattar olika nivåer av abstraktion. Framtida arbeten bör undersöka en större spännvidd av detaljnivåer för att ta reda på vad som fungerar bäst, vilket förhoppningsvis kan motivera spelskapare att använda sig av stilen mer.

No description available.