The thesis deals with the preparation, characterization and, in particular, with the switching properties of phase-change material (PCM) thin films. The films were deposited using the Pulsed Laser Deposition (PLD) technique. Phase transformations in these films were triggered by means of thermal annealing, laser pulses, and electrical pulses. The five major physical aspects structure transformation, crystallization kinetics, topography, optical properties, and electrical properties have been investigated using XRD, TEM, SEM, AFM, DSC, UV-Vis spectroscopy, a custom-made nanosecond UV laser pump-probe system, in situ resistance measurements, and conductive-AFM. The systematic investigation of the ex situ thermally induced crystallization process of pure stoichiometric GeTe films and O-incorporating GeTe films provides detailed information on structure transformation, topography, crystallization kinetics, optical reflectivity and electrical resistivity. The results reveal a significant improvement of the thermal stability in PCM application for data storage. With the aim of reducing the switching energy consumption and to enhance the optical reflectivity contrast by improving the quality of the produced films, the growth of the GeTe films with simultaneous in situ thermal treatment was investigated with respect to optimizing the film growth conditions, e.g. growth temperature, substrate type. For the investigation of the fast phase transformation process, GeTe films were irradiated by ns UV laser pulses, tailoring various parameters such as pulse number, laser fluence, pulse repetition rate, and film thickness. Additionally, the investigation focused on the comparison of crystallization of GST thin films induced by either nano- or femtosecond single laser pulse irradiation, used to attain a high data transfer rate and to improve the understanding of the mechanisms of fast phase transformation. Non-volatile optical multilevel switching in GeTe phase-change films was identified to be feasible and accurately controllable at a timescale of nanoseconds, which is promising for high speed and high storage density of optical memory devices. Moreover, correlating the dynamics of the optical switching process and the structural information demonstrated not only exactly how fast phase change processes take place, but also, importantly, allowed the determination of the rapid kinetics of phase transformation on the microscopic scale. In the next step, a new general concept for the combination of PCRAM and ReRAM was developed. Bipolar electrical switching of PCM memory cells at the nanoscale can be achieved and improvements of the performance in terms of RESET/SET operation voltage, On/Off resistance ratio and cycling endurance are demonstrated. The original underlying mechanism was verified by the Poole-Frenkel conduction model. The polarity-dependent resistance switching processes can be visualized simultaneously by topography and current images. The local microstructure on the nanoscale of such memory cells and the corresponding local chemical composition were correlated. The gained results contribute to meeting the key challenges of the current understanding and of the development of PCMs for data storage applications, covering thin film preparation, thermal stability, signal-to-noise ratio, switching energy, data transfer rate, storage density, and scalability.

Innovative methods for providing sustainable heating and cooling through thermal energy storage (TES) have gained increasing attention as heating and cooling demands in the built environment continue to climb. As energy prices continue to soar and systems reach their maximal capacity, there is an urgent need for alternatives to alleviate peak energy use. TES systems allow decoupling of energy production from energy utilization, both in location and in time. It is shown in this thesis that successful implementation of TES in the built environment alleviates peak energy load and reduces network expansion as well as the marginal energy production cost. This thesis analyzes phase change material (PCM) based TES systems in terms of material property characterization, numerical modeling and validation of thermal storage, as well as case specific techno-economic feasibility studies of system integration. The difficulties identified in latent heat TES design, such as heat transfer aspects, subcooling and identification of phase separation, have been analyzed through Temperature-History mapping and TES numerical modeling with experimental validation. This work focuses on the interdependency between resource availability, thermal charge/discharge power and storage capacity. In a situation where resource availability is limited, e.g. when using free cooling, waste heat or off-peak storage, the thermal power and storage capacity are strongly interrelated and should always be considered in unison to reach an acceptable techno-economic solution. Furthermore, when considering TES integration into an existing thermal energy distribution network, three adverse aspects are revealed in the Swedish case study: the single tariff system, the low-return temperature penalty, and the low storage utilization rate. These issues can be overcome through better adapted policies and optimized storage control strategies. Finally, despite the currently unfavorable conditions in the Swedish energy system, it is shown that TES has the potential to mitigate climate change through greenhouse gas emission reduction by displacing fossil-fuel based marginal thermal energy production. / QC 20110629 / Cold Thermal Energy Storage

This research work is focused on a conceptual combination of membrane-based energy recovery ventilator (ERV) and phase change material (PCM) to provide energy savings in building heating, ventilation & air-conditioning (HVAC) systems. An ERV can recover thermal energy and moisture between the outside fresh air (OFA) entering into the building and the exhaust air (EA) leaving from the building thus reducing the energy consumption of the HVAC system for cooling and heating the spaces inside the building. The membranes were stacked parallel to each other forming adjacent channels in a counter-flow arrangement for OFA and EA streams. Heat and moisture is diffused through the membrane core. Flat-plate encapsulated PCM is arranged in OFA duct upstream/downstream of the ERV thereby allowing for further reduction in temperature by virtue of free cooling. Paraffin-based PCMs with a melting point of 24°C and 31°C is used in two different configurations where the PCM is added either before or after the ERV. Computational fluid dynamics (CFD), and heat and mass transfer modeling is employed using COMSOL Multiphysics v5.3 to perform the heat and mass transfer analysis for the membrane-based ERV and flat-plate PCMs. An 8-story office building was considered to perform building energy simulation using eQUEST v3.65 from Department of Energy (DOE). Based on the heat and mass transfer analysis, it is found that the sensible effectiveness (heat recovery) stood in the range of 65%-97% while the latent effectiveness (moisture recovery) stood at 55%-80%. Also, the highest annual energy savings achieved were 72,700 kWh in electricity consumption and 358.45 MBtu in gas consumption.

<p>  </p> <p>Thermal energy storage (TES) is used to reduce the operating costs of heating, ventilation, and air conditioning (HVAC) systems by shifting loads away from on-peak periods, to reduce the maximum heating or cooling capacity needed from the HVAC system, and to store excess energy generated by on-site solar power. The most commonly-used form of TES is ice storage with air conditioning (A/C) systems in commercial buildings. There has been extensive research into many other forms of TES for use with HVAC systems, both in commercial and residential buildings. However, this research is often limited to use with either heating or cooling systems.</p> <p>Year-round, high-density storage for both heating and cooling would yield significantly larger cost savings than existing TES systems, particularly for residential buildings, where heating loads are often larger than cooling loads. This dissertation examines the feasibility of using metal hydrides for year-round storage, as well as analyzing the potential of variable-temperature energy storage for optimizing system performance beyond allowing for year-round use.</p> <p>Metal hydrides are metals that exothermically absorb and endothermically desorb hydrogen. Since the temperature this reaction occurs at depends on the hydrogen pressure, hydrides can be used for energy storage at varying temperatures. System architecture for using metal hydrides with an HVAC system is developed. A thermodynamic model which combines a dynamic model of the hydride reactors with a static model of the HVAC system is used to calculate operating costs, compared to a conventional HVAC system, for different utility rates and locations. The payback period of the system is unacceptably high, due to the high initial cost of metal hydrides and the operating costs of compressing hydrogen to move it between hydride reactors.</p> <p>In addition to the metal hydride system model, a generalized model of a variable-temperature TES system is used to determine the potential cost savings from dynamically altering the storage temperature to achieve optimal cost savings. Dynamic tuning does result in cost savings but is most effective for storage tank sizes significantly smaller than the optimal tank size. An alternate system design where the storage tank is charged with the outlet flow from the house achieves larger cost savings even for the optimally-sized tanks. Payback periods calculated for optimal sizing show that year-round storage has a lower payback period than separate cold and heat storage if the year-round storage system is not more expensive than two separate storage tanks. </p>

<p>To reduce greenhouse gas emissions, shifting the energy sources used in buildings, transportation, industry, etc., from fossil fuels to clean electricity is a trend. The increasing electricity demand stresses the existing electric grids. Buildings consume 73% of all U.S. electricity and are responsible for 30% of U.S. greenhouse gas emissions.  Residential and commercial buildings' space heating/cooling system consumes considerable electricity. Integrating thermal energy storage (TES) in building heating/cooling systems can mitigate the challenge of electric grids. Applying TES to existing air-source heat pump (ASHP) systems is the most studied for residential buildings. However, the high-quality thermal energy requirement for charging the TES tank results in low thermal performance of the ASHP system. Moreover, the failure of ASHP in cold climates requires a supplemental electric heater that significantly reduces the system efficiency and may lead to a higher annual peak for the grids.</p> <p>This study proposes integrating TES with ground-source heat pump (GSHP) systems as a more effective solution for building decarbonization due to the high efficiency of renewable-energy-based GSHPs year-round. This study focuses on proving the effectiveness of TES-integrated GSHPs for building decarbonization.  A dual-source heat pump (DSHP) with a hybrid TES and ground heat exchanger (GHE) named dual-purpose underground thermal battery (DPUTB) is investigated. The study uses modeling and experiments to verify the system's energy efficiency, decarbonization potential, and demand response capability. The modeling process involves developing various models, from component-level to system-level, and investigating advanced control strategies. A first-of-this-kind dynamic model of the DPUTB is developed to enable high-resolution system simulation for the GSHP system. The simulation is conducted using Modelica with rule-based control (RBC). A model predictive control (MPC) is also developed based on dynamic building envelope and heating, ventilation, and air conditioning (HVAC) system models. A cutting-edge co-simulation testbed integrates Modelica physical models with a MATLAB MPC controller model for advanced control evaluation. A prototype system of the DPUTB+DSHP is tested in a flexible research platform (FRP) at Oak Ridge National Laboratory (ORNL), which allows for component and system-level testing and remote automation controls. </p> <p>The study highlights the importance of proper insulation in the performance of the DPUTB, which consists of a TES tank enclosed by an outer tank functioning as a GHE. With appropriate insulation, a full-size DPUTB can store 1-ton cooling (3.5 kW) for four hours after eight hours of charging. Simulation results suggest that decoupling the TES with the GHE could reduce energy consumption by 27%.  System-level simulations confirm that the DSHP+DPUTB system, with a customized RBC, outperforms the conventional ASHP. The proposed system can reduce the annual HVAC electricity cost by up to 50% while saving 45% on electricity consumption. In the Northern areas of the United States, the annual peak load of the HVAC system can be reduced by 60%.  However, this reduction is less in the Southern parts of the as the system's higher efficiency in winter dominates the overall decrease. The application of MPC can further reduce the cost and energy consumption of the system by 35% theoretically. However, the accuracy of model prediction affects its performance in practical applications, which can be mitigated by employing technologies such as machine learning and reinforcement learning. Further research is required to verify these technologies.</p> <p>The DSHP+DPUTB system, a type of TES-integrated GSHP, has been well-designed and demonstrated superior performance to conventional systems, with greater flexibility and thermal efficiency. As a result, this system can enable electrification in the space heating sector without requiring an escalation in the grid. Moreover, alternative controls can be utilized to exploit its decarbonization potential fully.</p>

No description available.

<p>With the advent of increasingly complex radio systems at higher frequencies and the slowing of traditional CMOS process scaling with power concerns, there has been an increased focus on integration, architectural, and material innovations as a continued path forward in MEMS and logic. This work presents the first comprehensive experimental study of resonant body transistors in a commercial 14nm FinFET process, demonstrating differential radio frequency transduction as a function of transistor biasing through electrostatic, piezoresistive, and threshold voltage modulation. The impact of device design changes on unreleased resonator performance are further explored, highlighting the importance of phononic confinement in achieving an f*Q product of 8.2*10¹¹ at 11.73 GHz. Also shown are initial efforts towards the understanding of coupled oscillator architectures and a perovskite nickelate material system. Finally, development of resonators based on two-dimensional materials, whose scale is particularly attractive for high-frequency nano-mechanical resonators and acoustic devices, is discussed. Experiments towards dry transfer of tellurene flakes using geometries printed via two photon polymerization are presented along with optimization of a fabrication process for gated RF devices, presenting new opportunities for high-frequency electro-mechanical interactions in this topological material. </p>

No description available.

Geo-energy piles and walls have long been recognized as a promising way to reduce carbon dioxide emissions while providing renewable energy. However, enhancing the thermal performance of these structures has remained a signif-icant challenge. This thesis evaluated five different approaches to improving the thermal performance of geo-energy piles and walls, through a series of experiments using a fully instrumented testing rig. The first approach involved adding graphTHERM powder to concrete to double its thermal conductivity, boosting heat transfer efficiency by an impressive 50% to 66%. The second approach tested slag-based geopolymer concrete as a sustainable construc-tion material for geo-energy piles and walls, reducing CO2 emissions by 44.5% while improving thermal performance by 14% to 21%. The third approach in-volved testing thermally enhanced soils at the geo-energy structures/soil inter-face, resulting in an 81% improvement in heat transfer efficiency. The fourth approach utilized innovative phase change material (PCM) heat exchangers that increased heat transfer efficiency by 75% and 43% in heating and cooling operations, respectively. Finally, incorporated PCM-impregnated light weight aggregates at the interface of the structure soil, significantly increasing tem-perature difference and reducing thermal deformation of geo-energy struc-tures.Overall, these innovative approaches made a significant contribution to enhancing the thermal performance of geo-energy piles and walls. However, approaches four and five, which involve utilizing PCM heat exchangers and PCM-impregnated LWA's, respectively, showed extra benefits in dropping the thermal effect on soils and reducing the thermal damage on those structures. These techniques offer great promise for improving the thermal performance of geo-energy structures.

Tesis por compendio / [EN] The use of latent heat storage materials containing phase change materials (PCM's) is an effective way of buffering thermal fluctuations and has the advantages of high-energy storage density and the isothermal nature of the storage process. The aim of this work was to develop novel heat management materials based on the encapsulation of PCM's for different applications of interest in refrigerated foods. To this end, the electro-hydrodynamic processing was used to encapsulate commercial PCM's with transition temperatures of interest in refrigeration and superchilling within different polymer and biopolymer matrices. Initially, materials with heat management capacity to be used in refrigeration equipment and packaging applications were designed. To this end, thick slabs, multilayer heat storage structures and polystyrene foam trays containing ultrathin fiber-structured polystyrene/PCM coatings were fabricated through the encapsulation of commercial phase change materials (specifically paraffin's) within different polymeric matrices. The morphology, thermal properties, encapsulation efficiency and temperature profile of the just prepared structures and after three months of storage at 4 and 25ºC were evaluated. However, the developed electrospun heat management materials showed a multiple crystallization profile, increased supercooling degree (difference between the melting and crystallization temperatures), low encapsulation efficiency and partial diffusion out of the PCM from the electrospun structures during ageing. Therefore, different strategies were been carried out to counteract these drawbacks. One the one hand, thermal energy storage systems including a PCM which crystallize at -1.5ºC were optimized by adjusting the solvent composition in order to obtain hybrid electrospun fibers with thermal properties similar to those of the neat PCM. On the other hand, a hydrophilic shell material based on polyvinylalcohol (PVOH) was used to encapsulate the PCM by using the emulsion electrospinning technique in order to improve the encapsulation efficiency. However, the hybrid structures thus prepared were highly soluble in water at high relative humidity conditions and an extra layer of a more hydrophobic material (polycaprolactone) through coaxial electrospinning was used to protect them from swelling. The use of the coaxial configuration was a good strategy to preserve the morphology of the electrospun structures when exposed to high relative humidity. / [ES] El uso de materiales de almacenamiento de calor latente que contienen materiales de cambio de fase (PCM's) es una manera eficiente de amortiguar las fluctuaciones de temperatura y presenta las ventajas de proveer alta densidad de almacenamiento de energía y la naturaleza isotérmica del proceso de almacenamiento. El objetivo de este trabajo fue desarrollar nuevos materiales con capacidad de gestión de calor mediante la encapsulación de PCM's para diferentes aplicaciones de interés en alimentos refrigerados. Para ello, se utilizó el procesado electrohidrodinámico para encapsular PCM's comerciales con temperaturas de transición de fase de interés en refrigeración y superenfriamiento dentro de matrices poliméricas y biopoliméricas. Inicialmente, se diseñaron materiales con capacidad de gestión de calor para ser utilizados en equipos de refrigeración y aplicaciones de envasado. Con este propósito, se fabricaron bloques, estructuras multicapa y bandejas de poliestireno que contenían un recubrimiento de fibras nanoestructuradas ultrafinas mediante la encapsulación de materiales de cambio de fase (especialmente parafinas) dentro de diferentes matrices poliméricas. Se evaluó la morfología, propiedades térmicas, eficiencia de encapsulación y perfil de temperatura de las estructuras recién preparadas y después de tres meses de almacenamiento a 4 y 25ºC. No obstante, se observó que los materiales electroestirados con capacidad de gestión de calor presentaron un perfil de cristalización múltiple, un incremento en el grado de subenfriamiento (diferencia entre las temperaturas de fusión y de cristalización), baja eficiencia de encapsulación y una difusión parcial del PCM de las estructuras electroestiradas durante el periodo de almacenamiento. Para contrarrestar estos efectos, se llevaron a cabo dos estrategias diferentes. Por un lado, se optimizaron los sistemas de almacenamiento de energía térmica incluyendo un PCM que cristaliza a -1.5ºC mediante el ajuste de la composición de los disolventes con el fin de obtener fibras hibridas electroestiradas con propiedades térmicas similares al PCM puro. Por otro lado, para mejorar la eficiencia de encapsulación se utilizó un material hidrófilo basado en polivinilalcohol (PVOH) como material de recubrimiento para encapsular el PCM usando la técnica de electroestirado a partir de una emulsión. Sin embargo, se observó que las estructuras hibridas preparadas fueron altamente solubles en agua y en condiciones de alta humedad relativa. Por tanto, para protegerlos se incorporó una capa adicional de un material más hidrofóbico (policaprolactona) mediante la técnica de electroestirado coaxial. El uso de la configuración coaxial fue la mejor estrategia para preservar la morfología de las estructuras electroestiradas cuando éstas fueron expuestas a condiciones de alta humedad relativa. / [CA] L'ús de materials d'emmagatzematge de calor latent que contenen materials de canvi de fase (PCM) és una manera eficaç d'esmorteir les fluctuacions tèrmiques. A més a més presenta els avantatges de posseir una alta densitat d'emmagatzematge energia així com la naturalesa isotèrmica del procés d'emmagatzematge. L'objectiu d'aquest treball va ser desenvolupar productes amb capacitat de gestió de calor mitjançat l' encapsulació de PCM per a diferents aplicacions d'interès en la conservació d'aliments refrigerats. Amb aquesta finalitat, es va utilitzar el processament electro-hidrodinàmic per encapsular PCM comercials dins de diferents matrius polimériques i biopolimériques, amb temperatures de transició d'interès en el procés de conservació d'aliments refrigerats. Inicialment, es van dissenyar materials amb capacitat de gestió de calor per ser utilitzats en equips de refrigeració i en el envasat d'aliments refrigerats. Per a tal fi, es van dissenyar blocs, materials multicapa i safates de poliestirè que contenien un recobriment nanoestructurat i ultrafí amb encapsulats de materials de canvi de fase comercials (específicament parafines) dins de diverses matrius polimèriques. Es va caracteritzar la morfologia, les propietats tèrmiques, l'eficiència de encapsulació i la capacitat d'emmagatzematge d'energia just en el moment en el que es van preparar i després de tres mesos d'emmagatzematge a 4 y 25ºC. No obstant això, els materials desenvolupats van mostrar un perfil de cristal·lització múltiple, un augment del grau de subrefredament (diferència entre les temperatures de fusió i de cristal·lització), una baixa eficiència d'encapsulació i una difusió parcial del PCM de les estructures electroestirades durant el període d'emmagatzematge. Per tant, diferents estratègies han estat portades a terme per contrarestar aquests inconvenients. D'una banda, amb la finalitat d'obtenir fibres híbrides electroestirades amb propietats tèrmiques similars a les de la PCM pur, es van optimitzar els sistemes d'emmagatzematge d'energia tèrmica que incloïen un PCM que fon a -1,5 ºC variant la composició dels dissolvents. D'altra banda, es va utilitzar un material de la closca hidròfil basat en polivinílic alcohol (PVOH) per encapsular el PCM mitjançant l'ús de la tècnica d'electroestirat d'una emulsió per tal de millorar l'eficiència d'encapsulació. No obstant això, les estructures híbrides així preparades van ser altament soluble en aigua a altes condicions d'humitat relativa i va ser necessari utilitzar una capa addicional d'un material més hidròfob (policaprolactona) a través de la configuració coaxial de l'equip d'electroestirat. L'ús de la configuració coaxial va ser una bona estratègia per preservar la morfologia de les estructures electroestirades quan s'exposen a altes humitats relatives. / Chalco Sandoval, W. (2015). Development of Temperature Buffering Material Concepts Based on Electro-Hydrodynamic Processing of Interest in the Food Cold Chain [Tesis doctoral]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/53349 / Compendio