No description available.

Yes / Polymer extrusion is an energy intensive production process and process energy e ciency has become a key concern in the current industry with the pressure of reducing the global carbon footprint. Here, knowledge of the pattern of energy usage and losses of each component in the plant is highly useful in the process energy optimization. Moreover, it is essential to maintain the melt quality while improving the energy e ciency in polymer processing. In this work, an investigation was made on the total energy consumption, drive motor energy consumption, power factor and the melt temperature profile across the die melt flow (as an indication of the melt thermal quality) of an industrial scale extruder with three di erent screw geometries, three polymer types and wide range of processing conditions (altogether 135 di erent processing situations were observed). This aims to widen the knowledge on process energy and thermal behaviors while exploring possible correlation/s between energy demand and melt quality (in terms of melt temperature fluctuations across the melt flow). The results showed that the level and fluctuations of the extruder’s power factor is particularly dependent upon the material being processed. Moreover, it seems that there is a relation between the level of energy demand of the heaters and the level of melt temperature fluctuations. While the extruder specific energy consumption decreases with increasing screw speed, specific energy consumption of the drive motor may have either increasing or decreasing behavior. Overall, this study provides new insights in a wide range on process energy demand and melt thermal quality in polymer extrusion. Moreover, further research is recommended to establish strong correlation/s between process energy consumption and melt thermal quality which should help to enhance process control and hence the product quality in single screw polymer extrusion.

Yes / Extrusion is one of the fundamental production methods in the polymer processing industry and is used in the production of a large number of commodities in a diverse industrial sector. Being an energy intensive production method, process energy efficiency is one of the major concerns and the selection of the most energy efficient processing conditions is a key to reducing operating costs. Usually, extruders consume energy through the drive motor, barrel heaters, cooling fans, cooling water pumps, gear pumps, etc. Typically the drive motor is the largest energy consuming device in an extruder while barrel/die heaters are responsible for the second largest energy demand. This study is focused on investigating the total energy demand of an extrusion plant under various processing conditions while identifying ways to optimise the energy efficiency. Initially, a review was carried out on the monitoring and modelling of the energy consumption in polymer extrusion. Also, the power factor, energy demand and losses of a typical extrusion plant were discussed in detail. The mass throughput, total energy consumption and power factor of an extruder were experimentally observed over different processing conditions and the total extruder energy demand was modelled empirically and also using a commercially available extrusion simulation software. The experimental results show that extruder energy demand is heavily coupled between the machine, material and process parameters. The total power predicted by the simulation software exhibits a lagging offset compared with the experimental measurements. Empirical models are in good agreement with the experimental measurements and hence these can be used in studying process energy behaviour in detail and to identify ways to optimise the process energy efficiency.

Yes / Thermal stability is of major importance in polymer extrusion, where product quality is dependent upon the level of melt homogeneity achieved by the extruder screw. Extrusion is an energy intensive process and optimisation of process energy usage while maintaining melt stability is necessary in order to produce good quality product at low unit cost. Optimisation of process energy usage is timely as world energy prices have increased rapidly over the last few years. In the first part of this study, a general discussion was made on the efficiency of an extruder. Then, an attempt was made to explore correlations between melt thermal stability and energy demand in polymer extrusion under different process settings and screw geometries. A commodity grade of polystyrene was extruded using a highly instrumented single screw extruder, equipped with energy consumption and melt temperature field measurement. Moreover, the melt viscosity of the experimental material was observed by using an off-line rheometer. Results showed that specific energy demand of the extruder (i.e. energy for processing of unit mass of polymer) decreased with increasing throughput whilst fluctuation in energy demand also reduced. However, the relationship between melt temperature and extruder throughput was found to be complex, with temperature varying with radial position across the melt flow. Moreover, the melt thermal stability deteriorated as throughput was increased, meaning that a greater efficiency was achieved at the detriment of melt consistency. Extruder screw design also had a significant effect on the relationship between energy consumption and melt consistency. Overall, the relationship between the process energy demand and thermal stability seemed to be negatively correlated and also it was shown to be highly complex in nature. Moreover, the level of process understanding achieved here can help to inform selection of equipment and setting of operating conditions to optimise both energy and thermal efficiencies in parallel. / This work was funded through an inter-disciplinary research programme (Grant No. EP/G059330/1) by the EPSRC-UK. The technical assistance provided by Ken Howell, Roy Dixon and John Wyborn is greatly appreciated.