The removal of higher hydrocarbons from natural gas streams is an important separation that has been identified as a growth area for polymer membranes. An ideal membrane material for this separation would be more permeable to higher hydrocarbons (i.e., C3+ compounds) than to CH₄. This allows the CH₄ rich permeate to be retained at or near feed pressure, thus minimizing the requirement for repressurization followingmembrane separation. A polymer which demonstrates the ability to separate vapor from gases with high efficiency is poly [1-(trimethylsilyl)-1-propyne] (PTMSP). PTMSP is a stiff chain, high free volume glassy polymer well known for its very high gas permeability and outstanding vapor/gas selectivity. However, PTMSP is soluble in many organic compounds, leading to potential dissolution of the membrane in process streams where its separation properties are of greatest interest. PTMSP also undergoes significant physical aging, which is the gradual relaxation of non-equilibrium excess free volume in glassy polymers. Crosslinking PTMSP with bis(azide)s was undertaken in an attempt to increase the solvent resistance and physical stability of the polymer. A fundamental investigation into crosslinking PTMSP with a bis(azide) crosslinker was the focus of this thesis. Pure gas transport measurements were conducted with N₂, O₂, CH₄, C₂H6, C₃H₈, and n-C₄H₁₀ over temperatures raging from -20°C to 35°C and pressures ranging from 0 to 20 atm. Mixed gas permeation experiments were conducted using a 98 mol % CH₄, and 2 mol % n-C₄H₁₀ mixture. The mixed gas permeation experiments were conducted at temperatures ranging from -20°C to 35°C, and pressures ranging from 4 to 18 atm. Inorganic nanoparticles such as fumed silica (FS) were added to uncrosslinked and crosslinked PTMSP, and the effects of their addition on the transport properties were investigated. Crosslinking PTMSP with bis(azide)s increases its solvent resistance, and crosslinked films are insoluble in common PTMSP solvents such as toluene. At all temperatures, the initial pure and mixed gas permeabilities of crosslinked PTMSP films are less than those of uncrosslinked PTMSP. This decrease in permeability is consistent with the fractional free volume (FFV) decrease that accompanies crosslinking. Pure gas solubility coefficients are relatively unaffected by the crosslinking process, so the decrease in permeability is caused by decreases in diffusivity. The addition of FS nanoparticles increases the initial pure and mixed gas permeabilities of uncrosslinked and crosslinked PTMSP. The pure gas permeabilities and solubilities of all PTMSP films increase when the temperature decreases, while the diffusivities decrease. The rates of change in pure gas transport properties with temperature is similar for all films, so the temperature dependence of pure gas transport properties of PTMSP is unaffected by the addition of crosslinks or FS. The aging of uncrosslinked and crosslinked PTMSP films was investigated by monitoring N₂, O₂ and CH₄ permeabilities and FFV over time. The FFV and permeabilities of crosslinked films decreased over time, so crosslinking did not arrest the physical aging of PTMSP, as has been previously reported, and these differences in aging observations are likely to be a consequence of differences in post film casting thermaltreatments. The addition of 10 wt % polysiloxysilsesquioxanes (POSS) nanoparticles decreases the permeabilities of uncrosslinked and crosslinked PTMSP by approximately 70 %, and the permeability and FFV values of the resulting nanocomposite films were stable over the course of 200 days. In all PTMSP films, the mixed gas permeabilities of n-C₄H₁₀ increase with decreasing temperature, while the mixed gas CH₄ permeabilities decrease with decreasing temperature. As a result, the mixed gas n-C₄H₁₀/CH₄ permeability selectivities increase with decreasing temperatures. The addition of crosslinks and FS nanoparticles to PTMSP decreases the mixed gas n-C₄H₁₀/CH₄ permeability selectivities, and changes in the free volume characteristics of PTMSP caused by crosslinking and FS nanoparticles are thought to reduce the blocking of CH₄ permeation by n-C₄H₁₀. / text

In this abstract, we present a novel primary-multiple separation scheme which makes use of the sparsity of both primaries and multiples in a transform domain, such as the curvelet transform, to provide estimates of each. The proposed algorithm utilizes seismic data as well as the output of a preliminary step that provides (possibly) erroneous predictions of the multiples. The algorithm separates the signal components, i.e., the primaries and multiples, by solving an optimization problem that assumes noisy input data and can be derived from a Bayesian perspective. More precisely, the optimization problem can be arrived at via an assumption of a weighted Laplacian distribution for the primary and multiple coefficients in the transform domain and of white Gaussian noise contaminating both the seismic data and the preliminary prediction of the multiples, which both serve as input to the algorithm.

Separation anxiety is one of the most common behavioral disorder in companion dogs. Dogs not suffering from separation anxiety may still exhibit separation-related behaviors, which can differ depending on environmental contexts. In the present study, dogs without separation-related problems were video recorded during a short separation (3 min) from, and during reunion with, their owner. Comparison was done between if the dogs had played or been calm pre-separation. The dogs spent most time in proximity to the entrance and gazing towards where the owner left during separation. Their body-position was mostly standing, followed by sitting. All dogs were wining during separation, which occurred approximately four times more than barking. Dogs that had played pre-separation were running around more and had a longer latency to the first movement, compared to when they had been calm pre-separation. During reunion, when dogs had played pre-separation, they wagged their tail more and had a longer latency to lip licking, compared to when they had been calm pre-separation. The separation behaviors that occurred in this study aligns with previous work in this subject. Furthermore, one can suggest that play pre-separation might have an effect on separation behaviors, where speculations can be done if the positive affect associated with play might be the underlying cause for these findings.

Tall oil is a mixture of rosin acids, fatty acids, and non-acids resulting from acidification of the soaps separating out from the kraft pulp process evaporator liquor. The present uses of tall oil center chiefly around its fatty acid content, but are limited for some purposes because of the rosin content. Separation of these constituents makes each available as such. The rosin, as crystalline abietic acid, has specific possibilities as a raw material. Rosin and fatty acids are separated chiefly by distillation, although chemical means and extraction have been proposed to overcome such objections as corrosion and losses as pitch, incurred in distillation. Chlorination is used as a step in the purification of tall oil, or to produce a sticky chlorinated oil, but no separation based on the use of chlorine appears to have been proposed. It was proposed in this investigation to chlorinate the fatty acid double bonds in hopes that the properties of this product would be such as to permit of a separation. The effects of solvent, light, heat, and catalysts were studied to determine the optimum conditions for such a reaction, and the effect of chlorination upon the rosin and fatty acids, respectively, under specific conditions was determined, It was found that the use of CCl₄ solvent and ultraviolet light accelerate chlorine consumption and promote the addition of chlorine, but do not entirely stifle the substitution reaction. Rosin and fatty acid double bonds are attacked to about an equal extent under these conditions. The chlorinated oil is entirely soluble in most common solvents at room temperature. Petroleum ether insolubles increase slightly over the amount obtained from untreated oil. It is recommended that the range of chlorination conditions be extended to a more complete study of possible results, and that other chemical attacks be investigated. / Master of Science

Mixed matrix hollow fiber membranes maintain the ease of processing polymers while enhancing the separation performance of the pure polymer due to inclusion of molecular sieve filler particles. This work shows the development process of high loading mixed matrix hollow fiber membranes for butane isomer separation, from material selection and engineering of polymer-sieve interfacial adhesion to mixed matrix hollow fiber spinning. The matching of gas transport properties in polymer and zeolite is critical for forming successful mixed matrix membranes. The nC4 permeability in glassy commercial polymers such as Ultem® and Matrimid® is too low (< 0.1 Barrer) for commercial application. A group of fluorinated (6FDA) polyimides, with high nC4 permeability and nC4/iC4 selectivity, are selected as the polymer matrix. No glassy polymers can possibly match the high permeable MFI to make mixed matrix membranes with selectivity enhancement for C4s separation. Zeolite 5A, which has a nC4 permeability (~3 Barrer) and nC4/iC4 selectivity (essentially ∞), matches well with the 6FDA polymers. A 24% nC4/iC4 selectivity enhancement was achieved in mixed matrix membranes containing 6FDA-DAM and 25 wt% treated 5A particles. A more promising mixed matrix membrane contains 6FDA-DAM-DABA matrix and 5A, because of a better match of gas transport properties in polymer and zeolite. Dual layer hollow fibers, with cellulose acetate core layer and sheath layers of 6FDA polyimides, were successfully fabricated. Successive engineering of the 6FDA sheath layer and the dense skin is needed for the challenging C4s separation, which is extremely sensitive to the integrity of the dense skin layer. The delamination-free, macrovoid-free dual layer hollow fiber membranes provide the solution for the expensive 6FDA polyimides spinning. Mixed matrix hollow fiber membranes are spun base on the platform of 6FDA/Cellulose acetate dual layer hollow fibers. Preliminary results suggest that high loading mixed matrix hollow fiber membranes for C4s is feasible. Following research is needed on the fiber spinning with well treated zeolite 5A nanoparticles. The key aspect of this research is elucidating the three-step (sol-gel-precipitation) mechanism of sol-gel-Grignard treatment, based on which further controlling of Mg(OH)2 whisker morphologies is possible. A Mg(OH)2 nucleation process promoted by acid species is proposed to explain the heterogeneous Mg(OH)2 growing process. Different acid species were tried: 1) HCl solution, 2) AlClx species generated by dealumination process and 3) AlCl3 supported on zeolite surfaces. Acids introduced through HCl solution and dealumination are effective on commercial 5A particles to generate Mg(OH)2 whiskers in the sol-gel-Grignard treatment. Supported AlCl3 is effective on both commercial and synthesized 5A particles (150 nm-1 µm) during the sol-gel-Grignard treatment, in terms of promoting heterogeneous Mg(OH)2 whiskers formation. But the byproduct of Al(OH)3 layer separates the Mg(OH)2 whiskers from zeolite surface, and leads to undesirable morphologies for polymer-zeolite interfacial adhesion. The elucidation of sol-gel-Grignard mechanism and importance of zeolite surface acidity on Mg(OH)2 formation, builds a solid foundation for future development towards ''universal'' method of growing Mg(OH)2 whiskers on zeolite surfaces.

Robust industrially relevant membranes for CO₂ removal from aggressive natural gas feed streams were developed and characterized. Asymmetric hollow fiber membranes with defect-free selective skin layers on an optimized porous support substructure were successfully spun and subsequently stabilized by covalent crosslinking within the economical membrane formation process. Thermal treatment conditions, which promote sufficient crosslinking without introducing defects or undesired substructure resistance, were identified. It was found that crosslinking improves membrane efficiency and plasticization resistance as well as mechanical strength of fibers. The capability to maintain attractive separation performance under realistic operating conditions and durability against deleterious impurities suggests that the crosslinked fibers have great potential for use in diverse aggressive applications, even beyond the CO₂/CH₄ example explored in this work.

We examined the effect of the pore dimension of zeolites on the separation of gas mixtures using atomistic simulation methods. We studied two categories of the zeolites with small pores: pore modified silicalite for H₂/CH₄separation and small pore silica zeolites for CO₂/CH₄separation. The effect of pore modification of silicalite on the H₂/CH₄separation was examined. Under some degrees of surface modification, the CH₄flux was reduced much more than the H₂flux, resulting in high ideal selectivities. The use of small pore zeolites for CO₂/CH₄separations was studied. In DDR, we showed that CO₂diffusion rates are only weakly affected by the presence of CH₄, even though the latter molecules diffuse very slowly. Consequently, therefore, the permeance of CO₂in the equimolar mixtures is similar to the permeance for pure CO₂, while the CH₄permeance in the mixture is greatly reduced relatively to the pure component permeance. The calculated CO₂/CH₄separation selectivities are higher than 100 for a wide range of feed pressure, indicating excellent separation capabilities of DDR based membranes. Inspired by the observation in DDR we also examined the separation capabilities of 10 additional pure silica small pore zeolites for CO₂/CH₄separations. From these considerations, we predict that SAS, MTF and RWR will exhibit high separation selectivities because of their very high adsorption selectivities for CO₂over CH₄. CHA and IHW, which have similar pore structures to DDR, showed comparable separation selectivities to DDR because of large differences in the diffusion rates of CO₂and CH₄.

A new innovative polymer pyrolysis method was proposed for creation of attractive carbon molecular sieve (CMS) membranes. Oxygen exposure at ppm levels during pyrolysis was hypothesized and demonstrated to make slit-like CMS structures more selective and less permeable, which I contrary to ones expectation. Indeed prior to this work, any exposure to oxygen was expected to result in removal of carbon mass and increase in permeability. The results of this study indicated that the separation performance and CMS structure may be optimized for various gas separations by careful tuning of the oxygen level. This finding represents a breakthrough in the field of CMS membranes. Simple replacement of pyrolysis atmospheres from vacuum to inert can enable scale-up. The deviation in CMS membrane performance was significantly reduced once oxygen levels were carefully monitored and controlled. The method was shown to be effective and repeatable not only with dense films but also with asymmetric hollow fiber membranes. As a result, this work led the development of the "inert" pyrolysis method which has overcome the challenges faced with previously studied pyrolysis method to prepare attractive CMS membranes. The effect of oxygen exposure during inert pyrolysis was evaluated by a series of well-controlled experiments using homogeneous CMS dense films. Results indicated that the oxygen "doping" process on selective pores is likely governed by equilibrium limited reaction rather than (i) an external or (ii) internal transport or (iii) kinetically limited reaction. This significant finding was validated with two polyimide precursors: synthesized 6FDA/BPDA-DAM and commercial Matrimid®, which implies a possibility of the "inert" pyrolysis method application extending towards various precursors. The investigation was further extended to prepare CMS fibers. Despite the challenge of two different morphologies between homogeneous films and asymmetric hollow fibers, the "inert" pyrolysis method was successfully adapted and shown that separation performance can be tuned by changing oxygen level in inert pyrolysis atmosphere. Moreover, resulting CMS fibers were shown to be industrially viable. Under the operating condition of ~80 atm high pressure 50/50 CO2/CH4 mixed gas feed, the high separation performance of CMS fibers was shown to be maintained. In addition, elevated permeate pressures of ~20 atm did effect the theoretically predicted separation factor. While high humidity exposures (80%RH) resulted in reduced permeance, high selectivity was sustained in the fibers. Recommendations to overcome such negative effects as well as future investigations to help CMS membranes to be commercialized are provided.

A new concept of a "fiber sorbent" has been investigated. The fiber sorbent is produced as a pseudo-monolithic material comprising polymer (cellulose acetate, CA) and zeolite (NaY) by applying hollow fiber spinning technology. Phase separation of the polymer solution provides an appropriately porous structure throughout the fiber matrix. In addition, the zeolite crystals are homogeneously dispersed in the polymer matrix with high loading. The zeolite is the main contributor to sorption capacity of the fiber sorbent. Mass transfer processes in the fiber sorbent module are analyzed for hydrogen recovery and compared with results for an equivalent size packed bed with identical diameter and length. The model indicates advantageous cases for application of fiber sorbent module over packed bed technology that allows system downsizing and energy saving by changing the outer and bore diameters to maintain or even reduce the pressure drop. The CA-NaY fiber sorbent was spun successfully with highly porous structure and high CO2 sorption capacity. The fiber sorbent enables the shell-side void space for thermal moderation to heat of adsorption, while this cannot be applied to the packed bed. The poly(vinyl alcohol) coated CA-NaY demonstrated the thermal moderation with paraffin wax, which was carefully selected and melt at slightly above operating temperature, in the shell-side in a rapidly cycled pressure swing adsorption. So this new approach is attractive for some hydrogen recovery applications as an alternative to traditional zeolite pellets.

The goal of this project was to understand and model the performance of hybrid inorganic-organic membranes under realistic operating conditions for hydrocarbon gas/vapor separation, using butane isomers as the model vapors and a hybrid membrane of 6FDA-DAM-5A as an advanced separation system. To achieve the set goal, three objectives were laid out. The first objective was to determine the factors affecting separation performance in dense neat polymer. One main concern was plasticization. High temperature annealing has been reported as an effect means of suppressing plasticization. A study on the effect of annealing temperature was performed by analyzing data acquired via sorption and permeation measurements. Based on the findings from this study, a suitable annealing temperature was determined. Another factor studied was the effect of operating temperature. In deciding a suitable operating temperature, factors such as its possible effect on plasticization as well as reducing heating/cooling cost in industrial application were considered. Based on the knowledge that industrial applications of this membrane would involve mixture separation, the second objective was to understand and model the complexity of a mixed gas system. This was investigated via permeation measurements using three feed compositions. An interesting transport behavior was observed in the mixed gas system, which to the best of our knowledge, has not been observed in other mixed gas systems involving smaller penetrants. This mixed gas transport behavior presented a challenge in predictability using well-established transport models. Two hypotheses were made to explain the observed transport behavior, which led to the development of a new model termed the HHF model and the introduction of a fitting parameter termed the CAUFFV fit. Both the HHF model and CAUFFV fit showed better agreement with experimental data than the well-established mixed gas transport model. The final objective was to explore the use of mixed matrix membranes as a means of improving the separation performance of this system. A major challenge with the fabrication of good mixed matrix membranes was the adhesion of the zeolite particle with the polymer. This was addressed via sieve surface modification through a Grignard treatment process. Although a Grignard treatment procedure existed, there was a challenge of reproducibility of the treatment. This challenge was addressed by exploring the relationship between the sieves and the solvent used in the treatment, and taking advantage of this relationship in the Grignard treatment process. This study helped identify a suitable solvent, which allowed for successful and reproducible treatment of commercial LTA sieves; however, treatment of lab-made sieves continues to prove challenging. Based on improved understanding of the Grignard treatment reaction mechanism, modifications were made to the existing Grignard treatment procedure, resulting in the introduction of a "simplified" Grignard treatment procedure. The new procedure requires less control over the reaction process, thus making it more attractive for industrial application. Permeation measurements were made using mixed matrix membranes in both single and mixed gas systems. Selectivity enhancements were observed under both single and mixed gas systems using sieve loadings of 25 and 30wt%. The Maxwell model was used to make predictions of mixed matrix membrane performance. Although the experimental results were not in exact agreement with Maxwell predictions, the observed selectivity enhancement was very encouraging and shows potential for future application. Recommendations were made for future study of this system.