The main theme of this thesis is the usage of the test investigating the formation potential of trihalogenmethanes (THM FP) and its comparison with conventional indicators of water quality (CODMn, A254 and colours). As for the experimental part of the thesis, rating of the effectiveness of selected technological procedures has been applied (e.g.: coagulation, adsorption and ozonation in the act of treatment of artificially prepared water model with a higher content of humic substances in laboratory conditions). Based on the obtained results, it was found that the common indicators of water quality have very similar attributes and also complete each other. On the contrary, those attributes of indicators may not be sufficient in case of the evaluation of water quality with high content of humic substances. The findings made illustrate that the THM FP test enables the accurate evaluation of water quality, especially in connection with the content of an organic material susceptible to chemical changes. THM formation potential has proved its high value and also has confirmed that it can appropriately complete the other standarts that are being used for assessing the quality of treated water up to nowadays.

No description available.

Three oxidants have been evaluated for use as alternative chemical pretreatments for Fena Lake, a surface water that supplies the U.S. Navy's Public Water System (PWS) on the volcanic island of Guam. The study consisted of two investigative components. The first and primary component included a bench-scale evaluation to study the effects of different pre-oxidant chemicals on the formation of chlorinated disinfection by-products (DBPs). The second and ancillary component included a series of water treatment and distribution system management studies that analyzed DBP formation within the treatment plant and water distribution system. The goal of this research was to reduce total trihalomethane (TTHM) and the five haloacetic acid (HAA5) formations in the PWS. In the primary component of the research, raw surface water from Fena Lake was collected by U.S. Navy personnel and shipped to University of Central Florida (UCF) laboratories for experimentation. Bench-scale tests that simulated the coagulation, flocculation, sedimentation and filtration (CSF) that comprises the Navy Water Treatment Plant (NWTP) were used to evaluate the use of two alternative pre-oxidants, potassium permanganate (KMnO4) and chlorine dioxide (ClO2) in lieu of gaseous chlorine (Cl2). The research assessed DBP formation by comparing several pretreatment scenarios, namely: (1) no pretreatment, (2) chlorine pretreatment, and (3) alternative oxidant pretreatment. KMnO4 pretreatment resulted in the lowest percent reduction of TTHMs and HAA5 relative to chlorine pretreatment, at 5.7% and 22.7%, respectively; however, this amount was still a reduction from the results demonstrated for the chlorine pretreatment condition. Without using a pre-oxidant, TTHM and HAA5 formation were reduced by 22.8% and 37.3%, respectively, relative to chlorine pretreatment. Chlorine dioxide demonstrated the greatest TTHM and HAA5 reduction relative to chlorine pretreatment at 34.4% and 53.3%, respectively. The second component of research consisted of a series of studies that evaluated distribution system operations and management alternatives to identify opportunities that could achieve DBP reduction within the PWS. Three concerns that were addressed were the NWTP's compliance with the U.S. Environmental Protection Agency's (USEPA's) Stage 2 Disinfectants/Disinfection By-Products (D/DBP) Rule, variable hydraulic detention times within a small subdivision in the distribution system, and severe weather. It was determined that: (1) A decision based on in-plant studies to cease prechlorination at the NWTP resulted in a decrease in TTHMs and HAA5s throughout the distribution system by 62% and 75%, respectively; (2) A fluoride tracer study led to the discovery of a valved pipeline responsible for elevated DBPs because of excessive water age that when exercised and managed resolved intermittent DBP spikes in the PWS; and (3) when the NWTP's ballasted floc clarifier (BFC) was operated in-series prior to the conventional CSF process during severe weather conditions the TTHM and HAA5 were below 39 ug/L and 29 ug/L, respectively, proving BFC in-series is a practical option for the plant during severe weather.

Doctor of Philosophy / Department of Mechanical and Nuclear Engineering / Daniel V. Swenson / The objective of the thesis is to provide a fully coupled thermo-hydro-mechanical (THM) tool, T2STR, which enables quantitative understanding and prediction of thermal as well as mechanical effects on flow in the porous media under multiphase conditions. This is achieved by incorporating a finite element based hydro-thermo-mechanical stress capability into the well-established IFDM (Integrated Finite Difference Method) based flow simulation code TOUGH2. TOUGH2 is a program for calculation of multi-phase, multi-component, non-isothermal flow in porous media. It implements several equation of state modules to represent different fluid mixtures. The dual mesh technique is natural for combining both discretization methods and is used innovatively and effectively. A generalized approach is developed to accommodate the switching of variables implemented in TOUGH2 to adapt the phase changes. The forward coupling is achieved by using the thermal, hydrostatic, and poroelastic effects in the stress calculations. The backward coupling includes the effect of strain on the fluid flow. T2STR also allows the user to study the variation in porosity, permeability and capillary pressure as function of mean effective stress in the porous media. Multiple materials can be used to model the reservoir in T2STR, parallel to the implementation in TOUGH2. T2STR is implemented to carry out as a fully coupled, one way coupled (only deformation as function of hydro-thermal effects), or original TOUGH2 implementation. It provides the ability to switch on and off the thermal and/or poroelastic effects. T2STR is developed to model the fractured porous media using discrete fractures. The modeling of fractured porous media is limited to a staggered coupling approach. The fluid parameters like permeability, porosity are modified based on the stresses and/or aperture changes due to deformation. A set of verification problems, used to validate the code and display the capabilities of the code, are discussed. A graphical user interface is designed to pre-process the necessary data. Macros are developed for excel and Tecplot to post-process the results for easy visualization.

Clay formations are investigated worldwide as potential host rock for the deep geological disposal of high-level radioactive waste (HLW). Usually bentonite is preferred as the buffer and backfill material in the disposal system. In the disposal of HLW, heat emission is one of the most important issues as it can generate a series of complex thermo-hydro-mechanical (THM) processes in the surrounding materials and thus change the material properties. In the context of safety assessment, it is important to understand the thermally induced THM interactions and the associated change in material properties. In this work, the thermally induced coupled THM behaviours in the clay host rock and in the bentonite buffer as well as the corresponding coupling effects among the relevant material properties are numerically analysed. A coupled non-isothermal Richards flow mechanical model and a non-isothermal multiphase flow model were developed based on the scientific computer codes OpenGeoSys (OGS). Heat transfer in the porous media is governed by thermal conduction and advective flow of the pore fluids. Within the hydraulic processes, evaporation, vapour diffusion, and the unsaturated flow field are considered. Darcy’s law is used to describe the advective flux of gas and liquid phases. The relative permeability of each phase is considered. The elastic deformation process is modelled by the generalized Hooke’s law complemented with additional strain caused by swelling/shrinkage behaviour and by temperature change. In this study, special attention has been paid to the analysis of the thermally induced changes in material properties. The strong mechanical and hydraulic anisotropic properties of clay rock are described by a transversely isotropic mechanical model and by a transversely isotropic permeability tensor, respectively. The thermal anisotropy is described by adoption of the bedding-orientation-dependent thermal conductivity. The dependency of the thermal conductivity on the degree of water saturation, the dependency of the thermal effects on the water retention behaviour, and the dependency of the effects of the pore pressure variation on the permeability and the anisotropic swelling/shrinkage behaviour have been intensively analysed and the corresponding numerical models to consider those coupling effects have been developed. The developed numerical model has been applied to simulate the laboratory and in situ heating experiments on the bentonite and clay rock at different scales. Firstly the laboratory heating experiment on Callovo-Oxfordian Clay (COX) and the laboratory long-term heating and hydration experiment on MX80 pellets were simulated. Based on the knowledge from the numerical analysis of the laboratory experiments, a 1:2 scale in situ heating experiment of an integrated system of the bentonite engineered barrier system (EBS) in the Opalinus Clay host rock was simulated. All the relevant operation phases were considered in the modelling. Besides, the modelling was extended to 50 years after the heat shut-down with the aim of predicting the long-term behaviours. Additionally, variation calculations were carried out to investigate the effects of the storage capacity of the Opalinus Clay on the thermally induced hydraulic response. In the long-term modelling, the effects of different saturated water permeabilities of buffer material on the resaturation process were analysed. Based on the current researches and model developments, the observed THM behaviours of the bentonite buffer and the clay rock, that is, the measured evolution of temperature, pore pressure, humidity, swelling pressure, and so on in the laboratory and in situ experiments can be reproduced and interpreted well. It is proved that by using both a non-isothermal multiphase flow model and a non-isothermal Richards flow model combined with the corresponding thermal and mechanical models, the major THM behaviours can be captured. It is validated that the developed model is able to simulate the relevant coupled THM behaviours of clayey material under the well-defined laboratory conditions as well as under the complex natural disposal conditions.

O presente trabalho teve como objetivo avaliar a eficiência de pós-filtros adsorvedores constituídos de Carvão Ativado Granular (CAG) na remoção de compostos orgânicos precursores e na formação de subprodutos da desinfecção, em particular dos trialometanos (THM) na Estação de Tratamento de Água Alto da Boa Vista (ETA ABV), abastecida por reservatórios de água bruta com elevado grau de eutrofização. Os ensaios foram conduzidos em ETA Piloto composta por tanque de reservação de água filtrada, ozonizador, tanque de reservação de água ozonizada e 4 pós-filtros adsorvedores, sendo duas unidades dotadas de CAG de origem mineral e duas unidades dotadas de CAG de origem vegetal. Os filtros foram operados em paralelo, sendo que duas colunas foram alimentadas com água filtrada da ETA ABV (Filtro F3 CAG de origem mineral e Filtro F4 CAG de origem vegetal) e as outras duas alimentadas com água filtrada e ozonizada (Filtro F1 CAG de origem mineral e Filtro F2 CAG de origem vegetal). A avaliação da remoção de compostos orgânicos precursores e formação de subprodutos da desinfecção foi feita através de análises de carbono orgânico total (COT), UV-254 nm e formação de THM. A análise dos resultados gerados de julho de 2007 a dezembro de 2008 permitiu concluir que 93% do THM é formado nas primeiras 24 horas de contato da amostra com o cloro, simulando a pós cloração e pós alcalinização da ETA ABV. O processo de oxidação por ozônio não foi efetivo na remoção de THM instantâneo, visto que a média dos 38 valores de THM instantâneo para a água filtrada (17,8 ± 5,6 g/L) foi igual a média obtida para o THM instantâneo na água ozonizada. A remoção de THM pelos filtros de CAG foi mais significativa nos primeiros três meses de operação do sistema, apresentando remoção de 80% para os filtros com CAG de origem mineral e 70% para os filtros com CAG de origem vegetal, a partir do quarto mês de operação do sistema a remoção de THM caiu para um valor médio de 34%, o que mostra uma iminente saturação do leito adsorvedor. Os pós-filtros adsorvedores constituídos de CAG de origem mineral apresentaram melhor comportamento com respeito a remoção de THM e COT quando comparado com os pós-filtros dotados de CAG de origem vegetal. / The main purpose of this work was to evaluate the performance of a Granular Activated Carbon (GAC) post-filter adsorbers in the removal of organic precursors and in the formation of disinfection byproducts, especially trihalomethanes (THM) in Alto da Boa Vista Water Treatment Plant (ABV WTP), which takes raw water from a highly eutrophized reservoirs. The tests was conducted on a Pilot WTP composed of filtered water tank, ozonator, ozonized water tank, and four post-filter adsorbers: two units with mineral GAC media and two units with vegetal GAC media. The filters were operated in parallel, with two columns fed with filtered water from ABV WTP (F3 Filter mineral GAC and F4 Filter vegetal GAC) and the other fed with ozonized water (F1 Filter mineral GAC and F2 Filter vegetal GAC). The evaluation of the removal of organic precursors and the formation of disinfection byproducts was made through analysis of Total Organic Carbon (TOC), UV-254 nm and THM formation. The results generated from July 2007 to December 2008 showed that 93% of THM is formed in the first 24 hours of contact with the chlorine in the sample, simulating the post chlorination and post alkalinization of ABV WTP in samples of filtered water, ozonized water, and post-filter adsorbers effluent. Ozone oxidation process was not effective in removing THM. Was found the same instantaneous THM values in the filtered water (17.8 g/L± 5.6 g/L) and in the ozonized water. During the first three months of post-filter adsorber operation, THM removal efficiencies were around 80% for F1 and F3 (mineral GAC media) and around 70% for F2 and F4 (vegetal GAC media). After four months of operation, THM removal efficiencies decreased to 34% average value, thus indicative of GAC saturation. Regarding THM and TOC removal efficacy, the mineral GAC performed better than the vegetal GAC.

O presente trabalho teve como objetivo avaliar a eficiência de pós-filtros adsorvedores constituídos de Carvão Ativado Granular (CAG) na remoção de compostos orgânicos precursores e na formação de subprodutos da desinfecção, em particular dos trialometanos (THM) na Estação de Tratamento de Água Alto da Boa Vista (ETA ABV), abastecida por reservatórios de água bruta com elevado grau de eutrofização. Os ensaios foram conduzidos em ETA Piloto composta por tanque de reservação de água filtrada, ozonizador, tanque de reservação de água ozonizada e 4 pós-filtros adsorvedores, sendo duas unidades dotadas de CAG de origem mineral e duas unidades dotadas de CAG de origem vegetal. Os filtros foram operados em paralelo, sendo que duas colunas foram alimentadas com água filtrada da ETA ABV (Filtro F3 CAG de origem mineral e Filtro F4 CAG de origem vegetal) e as outras duas alimentadas com água filtrada e ozonizada (Filtro F1 CAG de origem mineral e Filtro F2 CAG de origem vegetal). A avaliação da remoção de compostos orgânicos precursores e formação de subprodutos da desinfecção foi feita através de análises de carbono orgânico total (COT), UV-254 nm e formação de THM. A análise dos resultados gerados de julho de 2007 a dezembro de 2008 permitiu concluir que 93% do THM é formado nas primeiras 24 horas de contato da amostra com o cloro, simulando a pós cloração e pós alcalinização da ETA ABV. O processo de oxidação por ozônio não foi efetivo na remoção de THM instantâneo, visto que a média dos 38 valores de THM instantâneo para a água filtrada (17,8 ± 5,6 g/L) foi igual a média obtida para o THM instantâneo na água ozonizada. A remoção de THM pelos filtros de CAG foi mais significativa nos primeiros três meses de operação do sistema, apresentando remoção de 80% para os filtros com CAG de origem mineral e 70% para os filtros com CAG de origem vegetal, a partir do quarto mês de operação do sistema a remoção de THM caiu para um valor médio de 34%, o que mostra uma iminente saturação do leito adsorvedor. Os pós-filtros adsorvedores constituídos de CAG de origem mineral apresentaram melhor comportamento com respeito a remoção de THM e COT quando comparado com os pós-filtros dotados de CAG de origem vegetal. / The main purpose of this work was to evaluate the performance of a Granular Activated Carbon (GAC) post-filter adsorbers in the removal of organic precursors and in the formation of disinfection byproducts, especially trihalomethanes (THM) in Alto da Boa Vista Water Treatment Plant (ABV WTP), which takes raw water from a highly eutrophized reservoirs. The tests was conducted on a Pilot WTP composed of filtered water tank, ozonator, ozonized water tank, and four post-filter adsorbers: two units with mineral GAC media and two units with vegetal GAC media. The filters were operated in parallel, with two columns fed with filtered water from ABV WTP (F3 Filter mineral GAC and F4 Filter vegetal GAC) and the other fed with ozonized water (F1 Filter mineral GAC and F2 Filter vegetal GAC). The evaluation of the removal of organic precursors and the formation of disinfection byproducts was made through analysis of Total Organic Carbon (TOC), UV-254 nm and THM formation. The results generated from July 2007 to December 2008 showed that 93% of THM is formed in the first 24 hours of contact with the chlorine in the sample, simulating the post chlorination and post alkalinization of ABV WTP in samples of filtered water, ozonized water, and post-filter adsorbers effluent. Ozone oxidation process was not effective in removing THM. Was found the same instantaneous THM values in the filtered water (17.8 g/L± 5.6 g/L) and in the ozonized water. During the first three months of post-filter adsorber operation, THM removal efficiencies were around 80% for F1 and F3 (mineral GAC media) and around 70% for F2 and F4 (vegetal GAC media). After four months of operation, THM removal efficiencies decreased to 34% average value, thus indicative of GAC saturation. Regarding THM and TOC removal efficacy, the mineral GAC performed better than the vegetal GAC.

Le développement et la mise au point d'un appareillage ont été réalisés dans le but d'effectuer la croissance par THM de CdIn2Te4. Des caractérisations physico-chimiques et cristallographiques du matériau ont été effectuées en parallèle avec une étude optique par spectroscopies IR et Raman. Des mesures de permittivité électrique et d'effet Hall ont été complétées par l'étude des caractéristiques I(V) et C(V) de diodes Schottky réalisées avec CdIn2Te4

Pour étudier l'influence de la gravité sur la croissance par T.H.M. du semi-conducteur CdTe dopé indium (programme EURECA), nous avons effectué une analyse comparative d'expérience spatiales et terrestres, complétée par une simulation numérique de l'hydrodynamique de la phase fluide utilisant un code 3D. Notre deuxième objectif a été de prépérer des monocristaux de CdTe dopé vanadium par la technique Bridgman présentant de bonnes propriérés photoréfractives. Pour une meilleure compréhension du mécanisme de l'effet photoréfractif, les matériaux ont été caractérisés par R.P.E., D.C.M. et P.I.C.T.S. afin de déterminer le degré de valence de V et la signature des niveaux vanadium dans la bande interdite. Des mesures optiques (absorption, photoconductivité...) et d'effet photoréfractif ont été effectuées. Enfin, pour évaluer la pertinence spatiale de cette croissance, nous avons étudié par simulation numérique l'influence de la gravité sur la configuration hydrodynamique de la phase fluide.

Theoretical part of the diploma thesis purveys information on drinking water and quality requirements, changes of drinking water quality during distribution and accumulation caused by disinfection, chemical processes, corrosion of constructional materials, incrusting solids, biofilms, nitrification of ammonia nitrogen, sediments in pipelines, elution of harmful matter. Attention was given to drinking water quality indicators which are associated with changes in drinking water distribution systems. In experimental part are studied changes of drinking water quality during distribution on the basis of selected drinking water quality indicators. There is specifically chemical oxygen demand, concentration of iron, manganese, ammonia ions, nitrites, nitrates, chloroform and chlorine. For periodical monitoring were selected suitable locality within the framework of Brno distribution system; for illustration were taken water samples from distribution systems of drinking water treatment plants Švařec, Vír, Štítary and Mostiště. For selected methods of analytical determination of above mentioned drinking water quality indicators are presented their characteristics. Obtained information on drinking water quality is mentioned in tabular and graphical form.