Placing recrystallization annealing in a manufacturing proces is often necessary in order to restore plasticity of worked blanks right before working products to its final shape. For better understanding of processes which are taking place in a material during annealing the use of in-situ techniques is favorable. Such observations enable us to watch changes in the materiál in real time at the original spot. Observations at grain-level are ideally made with scanning electron microscope – SEM by electron back-scattered diffraction – EBSD. The technique makes watching nucleation, growth and potential coarsening of recrystallized grains possible. Special construction of a tensile stage allows us to watch changes of a sample during tensile tests which can be used in observing influence of MnS inclusions on plasticity of free-cutting steels. Materials studied in this work are commonly used free-cutting steel 11SMnPb30 and its lead-free alternative 11SMnBi30.

This diploma thesis deals with the analysis of mechanical properties of bimetallic materials with clad layer of Inconel. In the theoretical part of the work there is an analysis of the investigated bimetallic material. The following is a description of mechanical tests and methods for evaluating the integrity of the surface, which were used to determine the properties of bimetallic material. The experimental part focuses on individual tests of mechanical properties of the material. For each test, the procedure for the production of test specimens, a description of the test equipment, the performance of the tests, the evaluation of the data obtained and finally, the evaluation of the results obtained are given.

The thesis presents computational simulation of compression test of a nickel foam and the 3D reconstruction of micro-CT images was utilized to generate the foam’s model of geometry. Explicit FEM is used to simulate compression test using software tool LS-DYNA and the stress–deformation curve is obtained together with deformed model’s mesh used for subsequent analysis. Sensitivity analyses were performed to configure the model and ensure best fit with values obtained during real-life experiment. The ANSYS Classic environment was then used to simulate tensile test of the foam compressed to various thicknesses. The tensile moduli in three mutually perpendicular directions of nickel foam were computed and the results were compared to experimental values as well. The results of tensile test simulation revealed considerable anisotropy of the foam’s elastic behavior. It can be said that the measured experimental data correspond very well with the elastic properties obtained from simulation up to certain level of compression. Analysis of the relationship between the element size and tensile moduli showed a significant difference between fine and coarse mesh. The optimal level of discretization and the overall model configuration ensuring high level of accuracy is proposed in this thesis.

Physical aging of commercially produced polypropylene homopolymers Mosten was studied. The work is focused on monitoring the changes in physical properties of polymer in the time period 90 days from the date of preparation of the test specimen. The aging of polymers was realized at storage temperatures of 23 and 80 °C. The changes in crystallinity, yield strength, modulus, elongation and impact strength using DSC method, tensile tests and impact tests according to Charpy were monitored. Molecular weight distribution was determined by means of GPC at each polymer. Relationships between the changes in physical properties and polymer molecular weight were sought.

In this work have been identified mechanical and fatigue properties of magnesium alloy AZ31 with 0.5% calcium, which was cast using squeeze casting. In addition, it was observed microstructure of the alloys and made fractographic assessment of fracture surfaces after fatigue loading.

Microstructure and mechanical properties of AZ61 magnesium alloy in cast condition and after solution annealing were compared. The compare of mechanical properties of alloy, their hardness and microanalysis of occurring phases are included in this work. For compare has been used a light microscopy, tensile test, hardness measurements and scanning electron microscopy.

Reconnaissance of problems and parameters of square hollow profile bend. Finding (identification) of deformation of cross-section. Finding of suitability of unannealed material for component part. Finding of mechanical characteristics of welds and influence of their bend position. This finding was done on the basis of comparison of tensile tests and consequently aplicated to specific part where the suitability for use of unannealed material were proved.

The master’s thesis deals with the computational modelling of the mechanical testing of isolated smooth muscle cells. The main aims are to create computational model of a cell, to simulate single-axis tensile test and to modify the model so that the model reflects real mechanical response. The model of the cell includes cytoplasm, nucleus, cell membrane and cytoskeleton which is modelled as a tensegrite structure. On this model the tensile test was simulated in case of the cell with cytoskeleton and the cell with distributed the cytoskeleton. Force-elongation curves, which were obtained from this simulation, were compared with experimental data which were taken from literature. Tensile properties were measured on freshly isolated cells from rat thoracic aorta, cultured cells, and cells treated with cytochalasin D to disrupt their actin filaments. It was found that the cytoskeleton influence on the cell load in computational model was smaller than in the real cell. Therefore the model was modified by changing material propreties and geometry so that the model of the cell corresponded with the different types of experimentally measured cells.

Cold spray is a novel coating method. Due to its low-temperature character, it has a potential to replace the high-temperature thermal spray processes in some applications. The presented work analyzes the microstructure and the phase composition of pure metal coatings deposited by cold spraying and evaluates selected mechanical properties. Specimens prepared by readily used HVOF industrial technology were used for comparison purposes.

The project was developed within the engineering degree in engineering technology, and is focused in welding together of two different materials. Welds will be done on a high strength steel Domex 420 MC and deep drawing steel DC01 using laser welding, and will be compared with the method of electron beam welding. Part of this project is a scientific research describing the basic physical principles of both methods, different types of lasers, welding material properties and inspection of welds. In the experimental part was carried tensile test, macroscopic and microscopic examination. Finally, work is to evaluate the individual tests.