Falls continue to be a major problem in the residential construction industry and account for a large number of injuries and fatalities each year (US Department of Labor, 2012).  The effects of a fall are catastrophic to the workers and their families as well as the construction company and surrounding community.  Prevention of these incidents has been the primary focus of organizations such as the Occupational Safety and Health Administration (OSHA).  To reduce the number of falls on residential construction sites, OSHA has put forth several standards that require the use of fall protection.  Although guidelines have been provided, there have been concerns and complaints regarding the standards as well as methods and materials that should be used. The goal of this research was to measure the behavior of a five truss roof system with various anchor points and bracing configurations loaded by a horizontal force.  A lab built roof system was used to test three different anchor types with three forms of temporary bracing.  The materials and methodology used in this testing were based on common materials and practices currently used in the residential construction industry. The results of this research show that anchors must engage multiple trusses to spread the applied load throughout the roof system.  Several forms of temporary bracing such as lateral, diagonal, and sway bracing, are also required to strengthen the roof system allowing it to withstand an applied load. / Master of Science

Bakgrund: Helamning rekommenderas de första sex månaderna och har många hälsomässiga fördelar för både moder och barn. Svårigheter vid amning kan kopplas till tidiga amningsstopp och kort tungband kan vara en orsak till dessa amningssvårigheter. Syfte: Syftet är att belysa mödrars erfarenheter av amningssvårigheter relaterat till kort tungband och av tungbandsklipp. Metod: Kvalitativ studie med induktiv ansats baserades på semistrukturerade intervjuer med tio informanter via video- eller telefonsamtal, strategiskt utvalda utifrån inklusions- och exklusionskriterier. Materialet analyserades med en tematisk innehållsanalys. Resultat: Mödrarnas erfarenheter av amningssvårigheter relaterat till kort tungband och tungbandsklipp kan visa sig som både fysiska eller psykiska symtom så som smärtande bröstvårtor och ångest. Flera av mödrarna upplevde att deras amningssvårigheter inte blev hörda eller uppmärksammade av vårdpersonalen samt att de upplevde ett bristande stöd. Flera upplevde också att det fanns en kunskapsbrist beträffande kort tungband inom vården och ett fåtal av mödrarna visste inte vad kort tungband var eller vad det innebar. Flera av mödrarna upplevde även att informationen kring själva tungbandsklippet var bristfällig samt vad de kunde vänta sig för resultat efteråt. Slutsats: Mödrar och barn med amningssvårigheter relaterat till kort tungband och tungbandsklipp får olika bemötande, bedömningar och åtgärder beroende på vilken kunskap som den vårdkontakt de möter besitter. Det finns ett behov av att arbeta fram en nationell handlingsplan för kort tungband hos barn för att alla ska få tillgång till samma vård. / Background: Exclusive breastfeeding is recommended the first six months of life and has many health benefits for both mother and child. Difficulties during breastfeeding can be associated with early breastfeeding cessation and tongue-tie can be one of the causes leading to breastfeeding difficulties.  Aim: The aim was to elucidate mothers’ experiences of breastfeeding difficulties in relation to tongue-tie and frenotomy.  Method: A qualitative inductive study based on semi-structured interviews with 10 informants via video- or telephone calls was conducted. Purposive sampling with inclusion- and exclusion criteria was chosen. Data was analyzed using a thematic content analysis.  Result: Mothers’ experiences of breastfeeding difficulties in relation to tongue-tie and frenotomy appear as both physical and psychological symptoms such as nipple pain and anxiety. Many of the mothers expressed that their difficulties were not heard or acknowledged by the health care staff and they also experienced a lack of support. Many of the mothers also experienced a lack of knowledge in the health care system regarding tongue-tie and a few of the mothers did not know what tongue-tie was or what it meant. Several of the mothers also experienced a lack of information regarding the frenotomy and what result they may expect afterwards.  Conclusion: Mothers and children with breastfeeding difficulties in relation to tongue-tie and frenotomy are treated and assessed differently depending on the knowledge of the health care staff. There is a need to develop a national careplan for children with tongue-tie so that all children have the same access to equal care

I det här examensarbetet har olika modelleringsantagandens påverkan på plattbroars och lådbalkbroars dynamiska egenskaper vid modellering av 3D-skalmodeller i FEM studerats. Delar av en bro som kan tänkas behöva någon typ av koppling har analyserats, liksom de kopplingar som är passande för sammanlänkningen av dessa delar. Studien har haft fokus på hur broarnas egenfrekvenser påverkas och hur broarna svarar på passage av höghastighetståg med avseende på accelerations- och förskjutningsamplituder för de olika modelleringsantagandena. De delar av en bro som studerats är kantbalk-konsol, konsol-broplatta, broplatta-stöd, lådbalk-broplatta och lastinföringspunkter-broplatta. Dessa delar har modellerats på olika sätt där till exempel förenklingar i modelleringen jämförts med modeller som är mer lika verkligheten. Resultatet visar att vid tågpassage ger vissa förenklingar från fall till fall responser som kan anses vara mer på den konservativa sidan. I övrigt är dock skillnaderna i respons sammantaget inte så stora. Resultatet visar också på att olika inställningar på kopplingar inte har så stor betydelse på studerade broars egenfrekvenser.

<p> The Fe-C-Mn phase diagram has been calculated from thermodynamic data. Experimentally determined tie-lines are in good agreement with the calculated diagram. </p> <p> It has been shown that the assumption that the austenite-ferrite interface is in a local equilibrium condition during the late stages of the transformation in highly supersaturated alloys and at all times in alloys in an area of low supersaturation is justified. The approximate solution to the diffusion equations correctly predicts the experimentally determined manganese concentration profiles. </p> <p> Hillert's concept of paraequilibrium has been examined and explicitly defined. The concentration given by a paraequilibrium calculation correctly predicts the experimentally observed growth rates of Kinsman and Aaronson (1967) for very highly supersaturated alloys. </p> <p> A convolution technique for use in the interpretation of strongly localized concentration changes determined by electron beam microanalysis has been developed. </p> / Thesis / Doctor of Philosophy (PhD)

No description available.

Many buildings today primarily serve the purpose of being envelopes that separate theindoor climate from the outdoors, for a large open area. Examples of these buildings arehall buildings of different sorts. In climates where the snow load often exceeds the deadload, like in Sweden, it can be hard to construct a budget-friendly yet strong roof structurefor these halls, especially if a span above 40 m is required. One solution that has gained popularity is the tie rod truss. Oftentimes it is not a real truss,but rather a beam that is equipped with one or more tie rods and one or more compressionstruts. The struts, which connect to the tie rods that run from one end of the roof to theother, support the main beam. This way, the tie rods can decrease the moment load on thebeams by carrying a tensile force. However, this results in an increased compressive loadon the beams. The large compressive forces in conjunction with the often slender beamsections can lead to instability out of the truss plane, and ultimately collapse. This is whathappened to the sports hall Tarfalahallen in 2020 in Kiruna, Sweden. The tie rod truss is an important structure; it is relatively cheap, saves material and is strongin the truss plane. But the instability problems can deter its use. The aim of this study istherefore to explore the different factors that could influence the stability of the structureand to what extent, by studying critical loads and the utilization of all structural elements. The study was performed by analyzing a finite element model of a real tie rod truss thattoday exists in a sports hall in Sweden. The analyses were done for different values of many parameters. The results were then extracted and processed such that the critical load and the utilization were plotted against the tested parameter values. The analysis and results processing were performed in an automated process that the author created himself. The results show that the stability of the model is strongly influenced by (1) the rigidity ofthe joints between beams and struts, (2) the rigidity of the joints between beams and roofing material and (3) the vertical position of potential stabilization systems that actperpendicularly to the truss plane. Pretension of the tie rods had a large effect on themaximum utilization and how it varies along the beams. Any potential reinforcement measure must be cost-effective, and therefore should addressthe three influential properties above. One suggestion is to add sideway bracing as close tothe joints between the struts and beams as possible. / Det finns många hus idag som byggs i syfte att vara klimatskal för en stor, öppen yta. Exempel på sådana hus är hallbyggnader av olika slag. I länder som Sverige, där snölasten många gånger är större än egentyngden, kan ett billigt men hållfast tak vara svårt att konstruera för dessa hallar, särskilt om spännvidder över 40 m krävs. En lösning som blivit populär är den underspända takstolen. I princip är det ett par balkar som skarvats så att de bildar en sadeltakstol eller en lång rak balk (pulpettakstol), och som stöttas av mellanstöd och stållinor (dragband) som löper från den ena balkänden till den andra via mellanstöden. Stållinorna kan då avlasta balkarna från momentbelastning genom att bära en dragkraft. Men samtidigt ökar tryckkraften i balkarna. De stora tryckkrafterna, i samband med att balktvärsnitten ofta görs väldigt slanka, kan leda till instabilitet ut ur takstolsplanet och därmed kollaps. Detta skedde i Tarfalahallen i Kiruna år 2020. Den underspända takstolen är en viktig konstruktion eftersom den är relativt billig,materialbesparande och väldigt hållfast i takstolsplanet. Men instabilitetsfenomenen kanförhindra fortsatt användning av konstruktionen. Därför undersöks i detta arbete vilka faktorer som kan påverka instabiliteten och i vilken grad, genom att studera kritiska laster och utnyttjandegrader. Studien utfördes genom att analysera en finita elementmodell av en verklig underspändtakstol som idag finns i en svensk gymnastikhall. Analyserna gjordes för olika värden på ett stort antal parametrar. Utdata från finita elementprogrammet extraherades därefter och bearbetades så att utnyttjandegraden i alla ingående bärverkselement beräknades. Sedan plottades dessa resultat mot de olika parametervärdena som testats. Analyserna och påföljande bearbetning utfördes i en automatiserad process som författaren själv skapade. Resultaten visar att modellens stabilitet är starkt beroende av (1) styvheten i förbindelsenmellan balk och mellanstöd, (2) styvheten i förbindelsen mellan balk och sekundärbärverkoch (3) det vertikala läget av eventuella stabiliseringssystem som verkar vinkelrätt mottakstolsplanet. Förspänning av stållinorna hade en betydlig inverkan på den maximalautnyttjandegraden och hur denna varierar längs balkarna. Eventuella förstärkningsåtgärder måste vara kostnadseffektiva, och därmed måste dessagälla de tre egenskaperna ovan. En åtgärd som föreslås sidostagning så nära stöttornasinfästningar som det går.

yes / There are very few, if any, available experimental investigations on aggregate interlock capacity along diagonal cracks in lightweight concrete deep beams. As a result, the shear design provisions including the modification factor of ACI 318-08 and EC 2 for lightweight concrete continuous deep beams are generally developed and validated using normal weight simple deep beam specimens. This paper presents the testing of 12 continuous beams made of all-lightweight, sand-lightweight and normal weight concrete having maximum aggregate sizes of 4, 8, 13 and 19 mm. The load capacities of beams tested are compared with the predictions of strut-and-tie models recommended in ACI 318-08 and EC 2 provisions including the modification factor for lightweight concrete. The beam load capacity increased with the increase of maximum aggregate size, though the aggregate interlock contribution to the load capacity of lightweight concrete deep beams was less than that of normal weight concrete deep beams. It was also shown that the lightweight concrete modification factor in EC 2 is generally unconservative, while that in ACI 318-08 is conservative for all-lightweight concrete but turns to be unconservative for sand-lightweight concrete with a maximum aggregate size above 13 mm. The conservatism of the strut-and-tie models specified in ACI 318-08 and EC 2 decreased with the decrease of maximum aggregate size, and was less in lightweight concrete deep beams than in normal weight concrete deep beams.

This study proposes various methods to harvest the mechanical energy present in railcar suspensions and railroad tracks to generate electricity that is suitable for onboard or trackside electronics, using electromagnetic generators. Compact electromagnetic energy harvesters that can be installed onboard railcars or wayside on railroad tracks are designed, fabricated, and tested. The designs integrate a mechanical motion rectifier (MMR) with embedded one-way clutches in the bevel gears in order to convert the bi-directional mechanical energy that commonly exists in the form of vibrations into a unidirectional rotation of the generator. The ball screw mechanism is configured such that it has reduced backlash and thus can more efficiently harvest energy from low-amplitude vibrations. Two prototype harvesters are fabricated and tested extensively in the laboratory using a suspension dynamometer and in the field onboard a railcar and on a test track. A power management system with an energy storage circuit has also been developed for this onboard harvester. The laboratory evaluation indicate that the harvesters are capable of harvesting power with sufficient current and voltage for successfully powering light electronics or charging a low demand battery pack. The harvested power varies widely from a few to tens of Watts, depending on the resistive load across the harvester and the amplitude and frequency of the mechanical motion. The laboratory test results are verified through field testing. One harvester is tested onboard a freight railcar, placing it across the wedge suspension, to use the small amount of relative displacement at the wedge suspension to harvest energy. A second harvester is placed on a test track to use the vertical motion that occurs due to passing wheels for wayside energy harvesting. Both onboard and wayside tests confirm the laboratory test results in terms of the success of the design concept in providing low-power electrical power. The harvester design is further integrated into a conventional railroad tie for ease of field installation and for improving the efficiency of harvesting the mechanical energy at the rail. The integrated design, referred to as the "smart tie," not only protects the energy harvester, the wiring harness, and supporting electronics from the maintenance-of-the-way equipment, but also positions the harvester in a mechanically advantageous position that can maximize the track-induced motion, and hence the harvested power. Although for testing purposes, the smart tie uses a modified composite tie, it can be integrated into other track tie arrangements that are used for revenue service track, including concrete and wooden ties. A prototype smart tie is fabricated for laboratory testing, and the results nearly surpass the results obtained earlier from the wayside harvester. The smart tie is currently being considered for revenue service field testing over an extended length of time, potentially at a railroad mega site or similarly suitable location. / Doctor of Philosophy / This dissertation proposes three different electromagnetic energy harvesters for harvesting railroad track and railcar suspension vibration energy. The concept is similar to what you may have seen in self-powering flashlights that are often advertised in late-night TV commercials. You shake the flashlight vigorously, which moves an energy harvester devoice and, Voila, the light bulb comes on. The device design in this study uses the mechanical energy that is present in a vehicle or at a railroad track to harvest the mechanical energy that is naturally present in the form of electrical energy, which can then be used for powering electronic devices and sensors of various kinds. Such sensors and electronics would help with improving the operational efficiency of railroads. The energy harvesters can be installed onboard a railcar or at the track. In either case, the movement of the train creates a small amount of vibration energy that is turned into electrical power. When onboard a train the power can be used for sensors, GPS, and similar devices to allow the operator to better monitor the condition and location of the train. Note that most railcars, especially the freight railcars, do not have any onboard electrical power. Similarly, the energy harvester can be installed at the track to convert the small amount of up and down motion that happens with the passing of each wheel into energy that could be used for integration of sensors that make the track "smarter." This means that the sensors can potentially alert the engineers who are responsible for monitoring the track of an existing or impending problem with the track. Both the railcar and track integration of the energy harvester that is designed, fabricated, and tested during this study are exciting concepts that can improve the rail industry in the U.S. This document includes the details of designing efficient energy harvesters, specifically for rail applications. A prototype of the energy harvester is fabricated and tested extensively in the lab and in the field, albeit to a more limited extent. The test results were quite successful, which is why I am telling you about them! Both the laboratory and field test results show that the device holds significant promise for rail applications.

Tesis por compendio / In the recent years, social network services, such as Facebook or LinkedIn, have experienced an exponential growth. People enjoy their functionalities, such as sharing photos, finding friends, looking for jobs, and in general, they appreciate the social benefits that social networks provide. However, as using social network has become routine for many people, privacy breaches that may occur in social network services have increased users' concerns. For example, it is easy to find news about people being fired because of something they shared on a social network. To enable people define their privacy settings, service providers employ simple access controls which usually rely exclusively on lists or circles of friends. Although these access controls are easy to configure by average users, research literature points out that they are lacking elements, such as tie strength, that play a key role when users decide what to share and with whom. Additionally, despite the simplicity of current access controls, research on privacy on social media reports that people still struggle to effectively control how their information flows on these services. To provide users with a more robust privacy framework, related literature proposes a new paradigm for access controls based on relationships. In contrast to traditional access controls where permissions are granted based on users and their roles, this paradigm employs social elements such as the relationship between the information owner and potential viewers (e.g., only my siblings can see this photo). Access controls that follow this paradigm provide users with mechanisms for disclosure control that represent more naturally how humans reason about privacy. Furthermore, these access controls can deal with specific issues that social network services present. Specifically, users often share information that concerns many people, especially other members of the social network. In such situations, two or more people can have conflicting privacy preferences; thus, an appropriate sharing policy may not be apparent. These situations are usually identified as multiuser privacy scenarios. Since relationship based access controls are complex for the average social network user, service providers have not adopted them. Therefore, to enable the implementation of such access controls in current social networks, tools and mechanisms that facilitate their use must be provided. To that aim, this thesis makes five contributions: (1) a review of related research on privacy management on social networks that identifies pressing challenges in the field, (2) BFF, a tool for eliciting automatically tie strength and user communities, (3) a new access control that employs communities, individual identifiers, tie strength, and content tags, (4) a novel model for representing and reasoning about multiuser privacy scenarios, employing three types of features: contextual factors, user preferences, and user arguments; and, (5) Muppet, a tool that recommends sharing policies in multiuser privacy scenarios. / En los últimos años, los servicios de redes sociales, como Facebook o LinkedIn, han experimentado un crecimiento exponencial. Los usuarios valoran positivamente sus muchas funcionalidades tales como compartir fotos, o búsqueda de amigos y trabajo. En general, los usuarios aprecian los beneficios que las redes sociales les aportan. Sin embargo, mientras el uso de redes sociales se ha convertido en rutina para mucha gente, brechas de privacidad que pueden ocurrir en redes sociales han aumentado los recelos de los usuarios. Por ejemplo, es sencillo encontrar en las noticias casos sobre personas que han perdido su empleo debido a algo que compartieron en una red social. Para facilitar la definición de los ajustes de privacidad, los proveedores de servicios emplean controles de acceso sencillos que normalmente se basan, de forma exclusiva, en listas o círculos de amigos. Aunque estos controles de acceso son fáciles de configurar por un usuario medio, investigaciones recientes indican que éstos carecen de elementos tales como la intensidad de los vínculos personales, que juegan un papel clave en cómo los usuarios deciden qué compartir y con quién. Además, a pesar de la simplicidad de los controles de acceso, investigaciones sobre privacidad en redes sociales señalan que los usuarios han de esforzarse para controlar de forma efectiva como su información fluye en estos servicios. Para ofrecer a los usuarios un marco de privacidad más robusto, trabajos recientes proponen un nuevo paradigma para controles de acceso basado en relaciones. A diferencia de los controles de acceso tradicionales donde los permisos se otorgan en base a usuarios y sus roles, este paradigma emplea elementos sociales como la relación entre el propietario de la información y su audiencia potencial (por ejemplo, sólo mis hermanos pueden ver la foto). Los controles de acceso que siguen este paradigma ofrecen a los usuarios mecanismos para el control de la privacidad que representan de una forma más natural como los humanos razonan sobre cuestiones de privacidad. Además, estos controles de acceso pueden lidiar con problemáticas específicas que presentan las redes sociales. Específicamente, los usuarios comparten de forma habitual información que atañe a muchas personas, especialmente a otros miembros de la red social. En tales situaciones, dos o más personas pueden tener preferencias de privacidad que entran en conflicto. Cuando esto ocurre, no hay una configuración correcta de privacidad que sea evidente. Estas situaciones son normalmente identificadas como escenarios de privacidad multiusuario. Dado que los controles de acceso basados en relaciones son complejos para el usuario promedio de redes sociales, los proveedores de servicios no los han adoptado. Por lo tanto, para permitir la implementación de tales controles de acceso en redes sociales actuales, es necesario que se ofrezcan herramientas y mecanismos que faciliten su uso. En este sentido, esta tesis presenta cinco contribuciones: (1) una revisión del estado del arte en manejo de privacidad en redes sociales que permite identificar los retos más importantes en el campo, (2) BFF, una herramienta para obtener automáticamente la intensidad de los vínculos personales y las comunidades de usuarios, (3) un nuevo control de acceso que emplea comunidades, identificadores individuales, la intensidad de los vínculos personales, y etiquetas de contenido, (4) un modelo novedoso para representar y razonar sobre escenarios de privacidad multiusario que emplea tres tipos de características: factores contextuales, preferencias de usuario, y argumentos de usuario; y, (5) Muppet, una herramienta que recomienda configuraciones de privacidad en escenarios de privacidad multiusuario. / En els darrers anys, els servicis de xarxes socials, com Facebook o LinkedIn, han experimentat un creixement exponencial. Els usuaris valoren positivament les seues variades funcionalitats com la compartició de fotos o la cerca d'amics i treball. En general, els usuaris aprecien els beneficis que les xarxes socials els aporten. No obstant això, mentre l'ús de les xarxes socials s'ha convertit en rutina per a molta gent, bretxes de privacitat que poden ocórrer en xarxes socials han augmentat els recels dels usuaris. Per exemple, és senzill trobar notícies sobre persones que han perdut el seu treball per alguna cosa que compartiren a una xarxa social. Per facilitar la definició dels ajustos de privacitat, els proveïdors de servicis empren controls d'accés senzills que normalment es basen, de forma exclusiva, en llistes o cercles d'amics. Encara que aquests controls d'accés són fàcils d'emprar per a un usuari mitjà, investigacions recents indiquen que aquests manquen elements com la força dels vincles personals, que juguen un paper clau en com els usuaris decideixen què compartir i amb qui. A més a més, malgrat la simplicitat dels controls d'accés, investigacions sobre privacitat en xarxes socials revelen que els usuaris han d'esforçar-se per a controlar de forma efectiva com fluix la seua informació en aquests servicis. Per a oferir als usuaris un marc de privacitat més robust, treballs recents proposen un nou paradigma per a controls d'accés basat en relacions. A diferència dels controls d'accés tradicionals on els permisos s'atorguen segons usuaris i els seus rols, aquest paradigma empra elements socials com la relació entre el propietari de la informació i la seua audiència potencial (per exemple, sols els meus germans poden veure aquesta foto). Els controls d'accés que segueixen aquest paradigma ofereixen als usuaris mecanismes per al control de la privacitat que representen d'una forma més natural com els humans raonen sobre la privacitat. A més a més, aquests controls d'accés poden resoldre problemàtiques específiques que presenten les xarxes socials. Específicament, els usuaris comparteixen de forma habitual informació que concerneix moltes persones, especialment a altres membres de la xarxa social. En aquestes situacions, dues o més persones poden tindre preferències de privacitat que entren en conflicte. Quan açò ocorre, no hi ha una configuració de privacitat correcta que siga evident. Aquestes situacions són normalment identificades com escenaris de privacitat multiusari. Donat que els controls d'accés basats en relacions són complexos per a l'usuari mitjà de xarxes socials, els proveïdors de servicis no els han adoptat. Per tant, per a permetre la implementació d'aquests controls d'accés en xarxes socials actuals, és necessari oferir ferramentes i mecanismes que faciliten el seu ús. En aquest sentit, aquesta tesi presenta cinc contribucions: (1) una revisió de l'estat de l'art en maneig de privacitat en xarxes socials que permet identificar els reptes més importants en el camp, (2) BFF, una ferramenta per a obtenir automàticament la força dels vincles personals i les comunitats d'usuaris, (3) un nou control d'accés que empra comunitats, identificadors individuals, força dels vincles personals, i etiquetes de contingut, (4) un model nou per a representar i raonar sobre escenaris de privacitat multiusari que empra tres tipus de característiques: factors contextuals, preferències d'usuari, i arguments d'usuaris; i, (5) Muppet, una ferramenta que recomana configuracions de privacitat en escenaris de privacitat multiusuari. / López Fogués, R. (2017). Enhancing Privacy Management on Social Network Services [Tesis doctoral]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/85978 / Compendio

Yes / The potentially broad application area in engineering design using Genetic Al- gorithm (GA) has been widely adopted by many researchers due to its high consistency and accuracy. Presented here is the initial design of a wideband non-dispersive wire bow-tie antenna using GA for breast cancer detection applications. The ultimate goal of this design is to achieve minimal late-time ringing but at higher frequencies such as that located from 4 to 8 GHz, in which is desire to penetrate human tissue for near field imaging. Resistively loading method to reduce minimal ringing caused by the antenna internal reflections is implemented and discussed when the antenna is located in free space and surrounded by lossy medium. Results with optimised antenna geometry and di®erent number of resistive loads are presented and compared with and without existence of scatterers.