Yes / This study established a dynamic damage constitutive model for ultra-high performance concrete (UHPC) with nanofillers, based on a viscoelastic dynamic constitutive model and a damage evolution equation. Ten types of nanofillers, including particle, tube and flake nanofillers, were incorporated to modify UHPC. The split Hopkinson pressure bar was used to obtain the relationship between stress and strain of UHPC specimens at a strain rate of 200/s-800/s. The experimental results indicated that the dynamic compressive strength of UHPC with nanofillers at strain rates of approximately 200/s, 500/s, and 800/s can reach 172.8 MPa, 219.6 MPa, and 275.9 MPa, respectively, reflecting an increase of 85.2 %, 76.5 %, and 53.9 % compared with the blank UHPC. The established dynamic damage constitutive model considered the damage accumulation with strains under dynamic loading. The fitting coefficients of the dynamic damage constitutive model, when compared against experimental results, range from 0.8796 to 0.9963, showing a higher accuracy compared with traditional Zhu-Wang-Tang (ZWT) viscoelastic model, especially at a strain rate of approximately 200/s. / National Science Foundation of China (52178118 and 52308236), and the China Postdoctoral Science Foundation (2022M720648 and 2022M710973) / The full-text of this article will be released for public view at the end of the publisher embargo on 5 Jan 2025.

Yes / The development of self-moderating and self-sensing concrete composites with high and stable thermal/electrical conductivity is essential to mitigate and monitor the temperature deformation behaviours (TDB) of engineering infrastructures such as highways, bridge pavements, airstrips and ports. Owing to the micron-scale diameter and high aspect ratio, stainless steel wires (SSWs) can establish a comprehensive and extensive thermal/electrical, as well as reinforcing, three-dimensional network within the concrete matrix, even at a low content. This paper thus investigated the TDB self-moderating and self-sensing performances of SSWs enhanced ultra-high performance concrete (UHPC). The main experiments were carried out on SSWs enhanced UHPC slabs, measuring 250 mm×225 mm×16 mm. The volume contents of SSWs studied were 0 %, 0.5 vol%, 1.0 vol% and 1.5 vol%. The TDB self-moderating and self-sensing experiments were carried out under different conditions, including indoor and outdoor environments. Such composites showed effective and highly stable capabilities in reducing the temperature difference and diminishing the strain of pavement slabs under different environmental conditions. Compared with the UHPC without SSWs, UHPC with 1.5 vol% of SSWs can reduce the temperature difference by 7.4 °C (39.4 %) when being heated from 21.6 °C to 50 °C, thus, reducing the maximum tensile/compressive strains by 83.1 %/82.2 %, and the tensile/compressive stresses by 70.8 %/82.0 %. At a heating rate of 67.1 °C/min, incorporating 1.5 vol% of SSWs results in significant reductions in both vertical displacement and stress, amounting to 98.6 % and 89.6 %, respectively. The 1.5 vol% SSWs reinforced UHPC slab also suppressed 25.0 % of temperature difference, 76.6 % of strain and 70.7 % of stress in scorching outdoor environments. The TDB of SSWs reinforced UHPC can be real-timely reflected by monitoring the quick and small-scale resistance fluctuations, and the fractional changes in resistivity can reach 5.24 % with a response time of 0.23 s. The self-moderating and self-sensing performances of such composites remained stable after repeated heating experiments, thus suggesting its potential for promising applications in engineering infrastructures which are susceptible to deformation under high-temperature conditions. / National Science Foundation of China (Grant Nos. 51908103 , 51978127 , and 52178188 ), and the Major Science and Technology Research Project of the China Building Materials Federation ( 2023JBGS10-02 ). / The full text will be available at the end of the publisher's embargo: 13th May 2025

This research develops and validates computational tools for the design and analysis of structural components and systems constructed with Ultra-High Performance Concrete (UHPC). The modeling strategy utilizes the Lattice Discrete Particle Model (LDPM) to represent UHPC material and structural member response, and extends a structural-level triaxial continuum constitutive law to account for the addition of discrete fibers. The approach is robust, general, and could be utilized by other researchers to expand the computational capability and simulate the behavior of different composite materials. The work described herein identifies the model material parameters by conducting a complete material characterization for UHPC, with and without fiber reinforcement, describing its behavior in unconfined compression, uniaxial tension, and fracture toughness. It characterizes the effect of fiber orientations, fiber-matrix interaction, and resolves the issue of multi-axial stress states on fiber pullout. The capabilities of the computational models are demonstrated by comparing the material test data that were not used in the parameter identification phase to numerical simulations to validate the models' predictive capabilities. These models offer a mechanics-based shortcut to UHPC analysis that can strategically support ongoing development of material and structural design codes and standards. / Ph. D. / This research develops and validates new computer-based methods to analyze and design civil infrastructure constructed with ultra-high performance concrete (UHPC), achieved when steel fibers are combined with a finely graded cement matrix. With superior performance characteristics in comparison to regular concrete, UHPC is studied herein for its strong potential to advance the durability, efficiency, and resiliency of new and existing infrastructure. The simulation-based methods are extensively verified with novel experiments that evaluate the material limits and failure modes when compressed, bent, or stretched, considering fiber volume and orientation. The computer-based tools can be used to realistically assess the structural performance of innovative UHPC applications in buildings, bridges, and tunnels under natural hazards, leading to surpassed levels of structural efficiency and resiliency across civil infrastructure.

Yes / Ultra-high performance concrete (UHPC), characterized by its high strength and toughness as well as durability, provides a promising solution for the construction of offshore wind towers (OWTs). This paper comprehensively reviews the durability and the dynamic mechanical properties of UHPC for OWTs under the impacts of the marine environment. Furthermore, the modifying effects of additives, including supplementary cementitious materials (SCMs) and reinforcing fibers, as well as nanofillers on UHPC are explored. Overall, UHPC possesses a dense microstructure that impedes the intrusion of harmful substances, and owing to the incorporation of additives, UHPC exhibits outstanding dynamic mechanical properties, making it an ideal material for applications in OWTs subjected to vibration fatigue and dynamic impact loads. Incorporating SCMs into UHPC can improve the durability and environmental benefits while maintaining similar dynamic mechanical properties concurrently. Nanofillers can serve as a beneficial supplement to steel fibers providing improved durability and dynamic mechanical properties by endowing UHPC dense microstructure and high system energy. Various models of marine environmental and loading actions on UHPC, examining ion transport, matrix degradation, and constitutive models, are concluded to gain insight into the underlying destructive mechanisms. These underlying mechanisms and the theoretical models further deepen the understanding of the service performance of UHPC in marine environments, thus providing the design guidance for the potential applications of UHPC in OWTs. / The authors thank the funding supported from the National Science Foundation of China (52308236 and 52368031), and the Major Science and Technology Research Project of the China Building Materials Federation (2023JBGS10–02), Natural Science Joint Foundation of Liaoning Province (2023-BSBA-077), and the Fundamental Research Funds for the Central Universities (DUT24GJ202). / The full-text of this article will be released for public view at the end of the publisher embargo on 19 Nov 2025.

Roofs are the most vulnerable part of the building envelope that often get damaged when subjected to hurricane winds. Damage to the roofs has a devastating impact on the entire structure, including interior losses and service interruptions. This study aimed at the development of a novel light-weight composite flat roof system for industrial, commercial and multi-story residential buildings to withstand Category 5 hurricane wind effects based on the Florida Building Code requirements for hurricane-prone regions, the strictest wind design code in the United States. The proposed roof system is designed as a combination of two advanced materials: ultra-high performance concrete (UHPC), reinforced with high strength steel (HSS). The novel combination of these two materials in a specially designed cross section led to a lightweight low-profile ultra-thin-walled composite roof deck, with only 17 pounds per square foot self-weight, 4-inch overall depth and only ¾-inch thick flanges and webs, with no shear reinforcement or stirrup. Two groups of specimens, single-cell and multi-cell, were fabricated and tested in four-point flexure to determine the ultimate bending capacity and ductility of the system. Each group of specimens included two short-span (9 ft.) samples (due to the laboratory constraints) -- one specimen subjected to positive bending and the other one subjected to negative bending, representing the critical loading conditions including the effects of wind pressures. All specimens exhibited pure flexural failure in a ductile behavior and with no sign of shear failure. Finite element models of laboratory specimens were also developed and calibrated based on experimental data in order to project the performance of the system for larger and more realistic spans. The experimental work and the finite element analyses showed that the proposed roof system with its given section has adequate flexural and shear strength, and also meets serviceability requirements for a 20-foot long span. Moreover, connections for the roof system were proposed, including panel-to-panel connections and roof-to-wall connections. In addition to safety, the other advantages of the proposed roof system in comparison to the equivalent reinforced concrete roofs include a three-fold reduction in self-weight, a three-fold reduction in overall profile height, and a five-fold reduction of steel reinforcement. Together, these advantages may lead to an increased span length beyond what is typically feasible for the conventional reinforced concrete slabs. All these features translate the proposed deck to a sustainable roof system.

The overall objective of this study was to develop an optimised Ultra-High-Performance Concrete (UHPC) matrix based on the modified Andreasen and Andersen optimum particle packing model by using available South African materials. The focus of this study was to determine the optimum combined fibre and superplasticiser content for UHPC by using a response surface design. The UHPC was appropriately designed, produced and tested. Various changes in mechanical properties resulting from different combinations of steel fibre and superplasticiser contents was investigated. The flowability, density and mechanical properties of the designed UHPC were measured and analysed. Both the fibre and superplasticiser content play a significant role in the flowability of the fresh concrete. The addition of fibres significantly improved the strength of the concrete. The results show that the superplasticiser content can be increased if a more workable mix is required without decreasing the strength significantly. The statistical analysis of the response surface methodology confirms that the designed models can be used to navigate the design space defined by the Central Composite Design. The optimum combined fibre and superplasticiser content depend on the required mechanical properties and cost. Using the modified Andreasen and Andersen particle packing model and surface response design methodology, it is possible to efficiently produce a dense Ultra-High-Performance Fibre Reinforced Concrete (UHPFRC) with a relatively low binder amount, low fibre content and good workability. The effect of heat curing on the mechanical properties was investigated. It was concluded that heat curing is not recommended when considering the long-term strength development. The estimated strength development of concrete obtained by using the fib Model Code 2010 (2013) does not incorporate the detrimental effect of high curing temperatures on long-term strength and therefore overestimate the long-term strengths. The strength estimates for both early and long-term ages can be improved by considering this effect in the strength development functions obtained from fib Model Code 2010 (2013). The effect of specimen size on the compressive and flexural tensile strength of UHPFRC members were established. It was found that the specimen size has a significant effect on the measured cube compressive strength. Smaller beam specimens showed higher ductility compared to those of the larger beam specimens. The crack width decreased as the beam’s depth decreased. A lower variability was experienced in the beams with limited depth (< 45 mm). Further testing is required to determine whether a span-to-depth ratio of 10 would yield optimum results. The utilisation of by-products, such as undensified silica fume and fly ash, as cement replacement materials makes UHPFRC sustainable, leading to a reduced life-cycle cost. The calculated Embodied Energy per unit strength (EE/unit strength) and Embodied Carbon per unit strength (EC/unit strength) values for the UHPFRC mixture yield lower values compared to that of the 30 MPa concrete mixture, indicating that UHPFRC can be used to reduce the environmental footprint of the concrete industry. The inverse analysis method used was successful in providing an improved simplified stress-strain response for the UHPFRC. The analysis provided valuable information into the stress-strain, load-deflection and moment-curvature responses of the UHPFRC. Standard material test results were used to theoretically calculate moment-curvature responses and were then compared to the experimental results obtained. The study demonstrated that it is possible to efficiently produce a dense and workable UHPFRC with relatively low binder amount and low fibre content. This can result in more cost-effective UHPFRC, thus improving the practical application thereof. / Dissertation (MEng)--University of Pretoria, 2020. / Civil Engineering / MEng (Structural engineering) / Unrestricted

O presente trabalho avaliou a influência dos concretos de ultra-alto desempenho com fibras (UHPFRC) e sem fibras (UHPC) no reforço de pilares curtos de concreto armado de seção transversal circular e quadrada. Avaliou-se também a adição de armaduras adicionais de reforço e de polímeros reforçados com fibras de carbono (PRFC) em alguns pilares reforçados. Para a avaliação deste novo sistema de reforço optou-se pela realização de um programa experimental e simulações numéricas. É importante ressaltar que no programa experimental, nenhum pilar reforçado possuía seção transversal maior que a seção do pilar de referência. Foi verificado por meio do programa experimental, que as camisas de UHPC apresentaram ruína de natureza frágil e não se recomenda a sua utilização a menos que acompanhada de mecanismos que garantam adequado confinamento do pilar reforçado. Nos pilares circulares e quadrados reforçados com UHPFRC foram verificados, respectivamente, incrementos de resistência de 106,4% e 83,6% onde o concreto do cobrimento foi substituído por UHPFRC, 154,3% e 111,7% onde além da substituição do cobrimento foram inseridas armaduras adicionais e 160% e 85,6% onde houve a colocação de PRFC após a substituição do cobrimento. Todos os pilares reforçados com UHPFRC não apresentaram destacamento da camisa de reforço. Foram realizadas simulações numéricas variando a espessura da camisa de UHPFRC e do número de camadas de PRFC tanto nos pilares de seção circular como nos pilares de seção quadrada. Por meio destas simulações, notou-se que a adição de pequenos incrementos de espessura da camisa de UHPFRC, proporciona elevados incrementos de resistência ao pilar reforçado, ao passo que o aumento do número de camadas de PRFC não influenciaria significantemente no incremento de resistência e sim na ductilidade do conjunto. / The present work evaluated the influence of ultra-high performance concrete with fibers (UHPFRC) and without fibers (UHPC) on the strengthening of short columns of reinforced concrete of circular and square cross section. It was also evaluated the addition of additional reinforcement and carbon fiber reinforced polymers (PRFC) on some strengthened columns. For the evaluation of this new system of strengthening we opted for the realization of an experimental program and numerical simulations. It is important to note that in the experimental program, no strengthened columns had a larger cross section than the reference column section. It was verified through the experimental program that the UHPC shirts presented ruin of a fragile nature and their use is not recommended unless accompanied by mechanisms that guarantee adequate confinement to the strengthened columns. In the circular and square columns strengthened with UHPFRC, respectively, resistance increments of 106.4% and 83.6% were verified, where the cover concrete was replaced by UHPFRC, 154.3% and 111.7%, in addition to the substitution of additional reinforcement were inserted and 160% and 85.6% where PRFC placement was performed after the replacement of the cover. All strengthened columns with UHPFRC did not present detachment of the strengthening jacket. Numerical simulations were performed by varying the thickness of the UHPFRC jacket and the number of PRFC layers on both the circular section columns and the square section columns. Through these simulations, it was noted that the addition of small thickness increments of the UHPFRC jacket would provide high increments of strength to the strengthened columns, while increasing the number of PRFC layers would not significantly influence the increase in strength but rather ductility of the assembly.

O presente trabalho avaliou a influência dos concretos de ultra-alto desempenho com fibras (UHPFRC) e sem fibras (UHPC) no reforço de pilares curtos de concreto armado de seção transversal circular e quadrada. Avaliou-se também a adição de armaduras adicionais de reforço e de polímeros reforçados com fibras de carbono (PRFC) em alguns pilares reforçados. Para a avaliação deste novo sistema de reforço optou-se pela realização de um programa experimental e simulações numéricas. É importante ressaltar que no programa experimental, nenhum pilar reforçado possuía seção transversal maior que a seção do pilar de referência. Foi verificado por meio do programa experimental, que as camisas de UHPC apresentaram ruína de natureza frágil e não se recomenda a sua utilização a menos que acompanhada de mecanismos que garantam adequado confinamento do pilar reforçado. Nos pilares circulares e quadrados reforçados com UHPFRC foram verificados, respectivamente, incrementos de resistência de 106,4% e 83,6% onde o concreto do cobrimento foi substituído por UHPFRC, 154,3% e 111,7% onde além da substituição do cobrimento foram inseridas armaduras adicionais e 160% e 85,6% onde houve a colocação de PRFC após a substituição do cobrimento. Todos os pilares reforçados com UHPFRC não apresentaram destacamento da camisa de reforço. Foram realizadas simulações numéricas variando a espessura da camisa de UHPFRC e do número de camadas de PRFC tanto nos pilares de seção circular como nos pilares de seção quadrada. Por meio destas simulações, notou-se que a adição de pequenos incrementos de espessura da camisa de UHPFRC, proporciona elevados incrementos de resistência ao pilar reforçado, ao passo que o aumento do número de camadas de PRFC não influenciaria significantemente no incremento de resistência e sim na ductilidade do conjunto. / The present work evaluated the influence of ultra-high performance concrete with fibers (UHPFRC) and without fibers (UHPC) on the strengthening of short columns of reinforced concrete of circular and square cross section. It was also evaluated the addition of additional reinforcement and carbon fiber reinforced polymers (PRFC) on some strengthened columns. For the evaluation of this new system of strengthening we opted for the realization of an experimental program and numerical simulations. It is important to note that in the experimental program, no strengthened columns had a larger cross section than the reference column section. It was verified through the experimental program that the UHPC shirts presented ruin of a fragile nature and their use is not recommended unless accompanied by mechanisms that guarantee adequate confinement to the strengthened columns. In the circular and square columns strengthened with UHPFRC, respectively, resistance increments of 106.4% and 83.6% were verified, where the cover concrete was replaced by UHPFRC, 154.3% and 111.7%, in addition to the substitution of additional reinforcement were inserted and 160% and 85.6% where PRFC placement was performed after the replacement of the cover. All strengthened columns with UHPFRC did not present detachment of the strengthening jacket. Numerical simulations were performed by varying the thickness of the UHPFRC jacket and the number of PRFC layers on both the circular section columns and the square section columns. Through these simulations, it was noted that the addition of small thickness increments of the UHPFRC jacket would provide high increments of strength to the strengthened columns, while increasing the number of PRFC layers would not significantly influence the increase in strength but rather ductility of the assembly.

abstract: Ultra High Performance (UHP) cementitious binders are a class of cement-based materials with high strength and ductility, designed for use in precast bridge connections, bridge superstructures, high load-bearing structural members like columns, and in structural repair and strengthening. This dissertation aims to elucidate the chemo-mechanical relationships in complex UHP binders to facilitate better microstructure-based design of these materials and develop machine learning (ML) models to predict their scale-relevant properties from microstructural information.To establish the connection between micromechanical properties and constitutive materials, nanoindentation and scanning electron microscopy experiments are performed on several cementitious pastes. Following Bayesian statistical clustering, mixed reaction products with scattered nanomechanical properties are observed, attributable to the low degree of reaction of the constituent particles, enhanced particle packing, and very low water-to-binder ratio of UHP binders. Relating the phase chemistry to the micromechanical properties, the chemical intensity ratios of Ca/Si and Al/Si are found to be important parameters influencing the incorporation of Al into the C-S-H gel. ML algorithms for classification of cementitious phases are found to require only the intensities of Ca, Si, and Al as inputs to generate accurate predictions for more homogeneous cement pastes. When applied to more complex UHP systems, the overlapping chemical intensities in the three dominant phases – Ultra High Stiffness (UHS), unreacted cementitious replacements, and clinker – led to ML models misidentifying these three phases. Similarly, a reduced amount of data available on the hard and stiff UHS phases prevents accurate ML regression predictions of the microstructural phase stiffness using only chemical information. The use of generic virtual two-phase microstructures coupled with finite element analysis is also adopted to train MLs to predict composite mechanical properties. This approach applied to three different representations of composite materials produces accurate predictions, thus providing an avenue for image-based microstructural characterization of multi-phase composites such UHP binders. This thesis provides insights into the microstructure of the complex, heterogeneous UHP binders and the utilization of big-data methods such as ML to predict their properties. These results are expected to provide means for rational, first-principles design of UHP mixtures. / Dissertation/Thesis / Doctoral Dissertation Engineering 2020

Ultra-high performance concrete (UHPC) has progressively gained interest because of its favorable strength and durability properties. Literature shows that curing temperature has a significant effect on the resultant mechanical properties of UHPC, generally resulting in increased compressive strength. However, limited datasets are currently available to ascertain the degree of change related to compressive strength as a function of curing temperature and conditions. This study investigates the effect of isothermal and submerged curing temperature conditions, ranging from 10°C to 90°C, on the compressive strength and elastic modulus development of UHPC and generates a numerical model to capture these effects. The extent and rate of compressive strength development in Cor-Tuf UHPC was found to increase with curing temperature, while only the rate of elastic modulus development increased with curing temperature. The numerical model shows reasonable agreement when compared with the experimental results and was successfully implemented in finite element analysis software.