Ceramics have been widely used for personnel and vehicle armour because of their desirable properties such as high hardness and low density. However the brittle nature associated with the ceramic materials, i.e. low toughness, reduces their ability to withstand multiple ballistic hits. The present work is focused on ceramic armour materials made from alumina and zirconia toughened alumina (ZTA). The effects of grain size and zirconia phase transformation toughening on the mechanical and high strain rate properties in both materials were investigated in detail. Alumina, 10%, 15% and 20% nano ZTA with 1.5 mol% yttria stabiliser were produced with various grain sizes. The processing of the materials started from suspension preparation, spray freeze drying of the suspension and die pressing to produce homogeneous green bodies with densities above 54%. Then, the green bodies were sintered using conventional single stage and/or two stage sintering to produce the samples with full density and a range of grain sizes (0.5 to 1.5 µm alumina grains and 60 to 300 nm zirconia grains). The effects of the processing conditions on the microstructures were studied and the optimum processing route for each sample was determined. The mechanical properties of the alumina and ZTA samples were investigated, including Vickers hardness, indentation toughness, 4-point bend strength and wear resistance. The results showed that, with an increasing amount of zirconia addition, evident increases of the toughness, strength and wear resistance properties were observed, whilst the hardness reduced slightly correspondingly. The effect of density and grain sizes on the hardness and toughness were studied as well: larger alumina grain size led to a higher hardness and negligible change in toughness, whilst the zirconia grain coarsening enhanced the phase transformation toughening effect and the samples displayed a higher toughness. In addition to the investigation of the mechanical properties, the alumina and nano ZTA samples were subjected to high strain rate testing, including split Hopkinson pressure bar (SHPB) (8-16 m/s) and gas gun impact testing (100-150 m/s). The high strain rate performances were compared in terms of their fracture behaviours, fragmentation process and fragment size distribution. Raman spectroscopy was used to measure the amount of zirconia phase transformation in ZTA samples after the high strain rate testing. The residual stress and dislocation density in alumina grains after testing were quantitatively measured using Cr3+ fluorescence spectroscopy. The results indicated that zirconia phase transformation can reduce the residual stress and dislocation densities in the ZTA samples, resulting in less damage, lower plastic deformation and less crack propagation. In addition, a nano zirconia material with 1.5 mol% yttria stabiliser (1.5YSZ) was subjected to a gas gun impact test with a very high impact speed (142 m/s); a deep projectile penetration was observed, due to the low hardness of the pure zirconia, whilst the sample stayed intact. The result further confirmed that the zirconia phase transformation toughening effect can improve the sample's high strain rate performance.

Pearly layers in seashells, also known as nacreous layers, are reported to be three orders of magnitude tougher than their primary constituent, aragonite. Their high toughness is attributed to a particular structure of alternating layers of natural ceramic and polymer materials. This work tries to emulate it using engineering materials. The thickness, strength, and stiffness of the ceramic layer; the thickness, stiffness, strength, and toughness of the polymer interface layer; and the number of layers are the factors that contribute to different degrees. Furthermore, understanding the relative contribution of different toughening mechanisms in nacre would enable identification of key parameters to design tough engineered ceramics. As a step towards that, in this thesis, layered ceramic beams replicating nacre were studied analytically, computationally, and experimentally. The insights and findings from these studies were then used to develop a new method to make tough layered ceramics mimicking nacre. Subsequently, the use of layered ceramics for armour applications was evaluated. Based on analytical numerical and experimental studies, we observed that the strength of the layers is a key factor to replicate the high toughness of nacre in engineered ceramics. We also demonstrated that, crack deflection and bridging observed in nacre in studies elsewhere, occur due to the high strength of platelets. Based on these findings, the new method developed in this study uses green alumina-based ceramic tapes stacked with screen printed stripes of graphite. During sintering, graphite oxidizes leaving empty channels in the stack. These channels were filled with tough interface materials afterwards. As a result, a ceramic- polymer composite with more than 2-fold increase in toughness was developed. Subsequently, we evaluated layered ceramics for armour applications based on numerical analysis validated with experiments. Consistent to the trends in literature, we observed that layers degrade the resistance to ballistic impact. However, improved energy absorption is demonstrated in layered ceramics. These conflicting dual trends were not presented and quantified in any earlier studies conducted elsewhere. Another new observation not documented earlier is the effect of interface strength. Using an interface material of sufficient strength, penetration resistance of layered ceramics can be improved beyond monolithic ceramics. Using these findings, new layered ceramic armour can be designed that is cost- effective and better performing than monolithic ceramics.