Le moteur essence à allumage par compression (GCI), reposant sur la combustion partiellement prémélangée de l'essence (GPPC), peut potentiellement assurer des opérations efficaces et propres. Le moteur GCI s'est avéré efficace à forte charge, mais l'indice d'octane élevé de l'essence limite considérablement les opérations à faible charge. Le présent travail étudie le potentiel de l'utilisation de l'ozone, fort agent oxydant, pour améliorer la réactivité de l'essence et permettre le fonctionnement à faible charge de GCI. L'ozone peut être produit on board en équipant le moteur d'un générateur d'ozone, sans impact dramatique sur le coût du moteur et sur la complexité du contrôle du moteur. Les essais effectués avec un moteur monocylindre ont montré que l'ozone favorise la combustion HCCI de l'essence, permettant d'étendre la limite d’auto-inflammation et de réduire la température minimale nécessaire de celle-ci. Les diagnostics optiques ont montré que ces propriétés sont liées à une prolifération radicale accrue, amenées par des réactions à basse température induites par l'ozone. En parallèle, le processus de combustion GCI a été étudié dans des conditions de faible charge. Sans ozone, la température d'admission doit être considérablement augmentée pour permettre l'auto-inflammationdes mélanges essence-air pauvres. De plus, les résultats indiquent que le monoxyde d’azote (NO) contenu dans les gaz brûlés résiduels peut, dans certaines conditions, favoriser fortement la combustion GCI. Ensuite,l'effet de l'ozone a été étudié dans des conditions d'injection directe GCI. Les résultats démontrent qu’une stratégie avec double injection est nécessaire pour maximiser l’effet promoteur de l’ozone et pour contrôler le processus de combustion GCI. Enfin, l'utilisation d’une forte concentration d’ozone a permis d’atteindre des opérations à faible charge en mode GCI, avec des faibles émissions de NOx et de suie, et cela, sans avoir besoin d'augmenter la température ou la pression d'admission. / Gasoline Compression Ignition (GCI) engine, relying on Gasoline Partially Premixed Combustion (GPPC) has potential for efficient and clean operations. GCI engine showed to be effective at high load, however, the highoctane number of gasoline dramatically limits low load operations. The present work investigates the potential of using ozone, a strong oxidizing agent, to improve gasoline reactivity and enabling low load GCI operation.Ozone can be produced in-situ and on-demand by equipping the engine with an ozone generator, without a dramatic impact on the engine cost and the engine control complexity. Experiments in a single cylinder engine showed that ozone promotes gasoline HCCI combustion, making possible to extend the lean limit and reducing the minimum temperature needed for autoignition. Optical diagnostics showed that these properties are related to an increased radical proliferation related to ozone-induced low temperature reactions. In parallel, GCI combustion process was investigated under low load conditions. Without ozone, the intake temperature should be considerable increased to enable auto ignition of lean gasoline-air mixtures. Moreover, results indicated that the NO contained into residual burnt gases can strongly promote GCI low load combustion. Finally, the effect of ozone was investigated under GCI direct-injection conditions, demonstrating that low load GCI operation with low NOx and Soot emission can be achieved by seeding the intake of the engine with ozone without needing of increasing the intake charge temperature or boosting the intake pressure.

Diesel engine emissions of oxides of nitrogen and particulate matter can be reduced simultaneously through the use of high levels of exhaust gas recirculation (EGR) to achieve low temperature combustion (LTC). Although the potential benefits of diesel LTC are clear, the main challenges to its practical implementation are the requirement of EGR levels that can exceed 60%, high fuel consumption, and high unburned hydrocarbon and carbon monoxide emissions. These limit the application of LTC to medium loads. In order to implement the LTC strategy in a passenger vehicle engine, a transition to conventional diesel operation is required to satisfy the expected high load demands on the engine. The investigation presented in this thesis was therefore aimed at improving the viability of the high-EGR LTC strategy for steady-state and transient operation. An experimental investigation was carried out on a single cylinder high-speed direct injection diesel engine. This thesis presents research on engine in-cylinder performance and engine-out gaseous and particulate emissions at operating conditions (i.e. EGR rate, intake pressure, fuel quantity, injection pressure) likely to be encountered by an engine during transient and steady-state operation. At selected operating points, further investigation in terms of in-cylinder spray and combustion visualization, flame temperature and soot concentration measurements provided deeper insight into the combustion and emissions phenomena. Increased intake pressure at single injection high-EGR LTC operation was investigated as a strategy to reduce the emissions of partial combustion by-products and to improve fuel economy. The higher intake pressure, although effective in reducing partial combustion by-products emissions and improving fuel economy, increased the EGR requirement to achieve LTC. A split fuel injection strategy with advanced injection timing on the other hand was effective in reducing the EGR requirement for LTC from 62% with single injection to 52% with split injections at 120 kPa (absolute) intake pressure. Unburned hydrocarbon emissions and fuel economy were particularly sensitive to intake oxygen mass fraction, and injection and dwell timings with the split injection strategy. In-cylinder soot formation and oxidation mechanisms with the split injection strategy were found to be significantly different from the single injection high-EGR LTC case. Transient simulation of an engine during combustion mode transition identified engine operating parameters on a cycle-by-cycle basis. Steady-state investigation of these test conditions provided significant insight into the combustion conditions and their effect on emissions and performance. The results from this thesis demonstrated the importance of optimizing both the air handling system performance and the fuel injection system during engine transients. The increased emissions and impaired performance due to slow response of the EGR and turbocharger systems during transitions to and from LTC modes can in part be mitigated through split injections optimized for the specific transient point. This provides a clear direction for engine developers to pursue in optimizing engine calibration when running with LTC-conventional diesel dual-mode strategies.

Within this body of work several series of experiments will investigate the nature of complex combustion in an experimental single-cylinder engine emulating a modern passenger car size compression-ignition (CI) engine. Regimes of single, piloted single and piloted split-main injections will be tested and compared in terms of combustion characteristics, specific emission output and cyclic behaviour to determine how increased injection complexity affects the emissions and output of the modern CI engine. Through these tests, the effect of fuel-line stationary waves will be demonstrated and investigated, showing conclusively that optimised engine calibration is essential to account for injector-generated waves in any multiple injection scenario. This data will then be confirmed with a dedicated analysis using an injector rate measuring tube. The tests will then be expanded to include examination into the behaviour of injector needle-lift standard deviation over its operating cycle, in-cylinder pressure standard deviation behaviour and trends over the combustion cycle as well as IMEP variability. Through these tests a novel method to detect start of combustion will be proposed and compared to conventional methods. Low temperature combustion (LTC) will be tested under incremental injection complexity. Tests will be optimised for combustion phasing and injection pressure, with a view to analysis of emissions, output and cyclic behaviour to establish whether the knowledge gained about conventional combustion holds true under LTC. Optimization of engine parameters will be shown to result in easier to implement LTC regimes with superior emissions characteristics. Finally, LTC tests will be expanded to include 30% and 50% by volume gas-to-liquid fuel (GTL) blends in order to determine whether fuel characteristics further influence emissions, output and cyclic behaviour in LTC through complex injection regimes. How GTL-blend ratio affects trends in emissions and cyclic behaviour will also be examined and compared to conventional diesel fuel.