Master of Science in Engineering - Engineering / The most significant benefit of co-disposal of tailings based on the “Paste and Thickened Tailings Disposal” concept is the improved ability to “design” the properties of the co-disposed tailings material to suit the surrounding environment. The overall aim of this study was to gain a better understanding of the relationship between the key slurry material characteristics and the flow behaviour of co-disposed tailings upon deposition, for the case of montmorillonite clay-based kimberlite tailings. A fundamental understanding of this relationship will enable the successful manipulation and exploitation of the co-disposed tailings rheology for optimal tailings disposal and the minimisation of associated financial, environmental and social risks. The key material characteristics selected for investigation were the vehicle solids concentration, suspension pH and vehicle to load ratio. The yield stress was selected as the key rheological property representing both the vehicle component rheology and co-disposed tailings rheology. Two yield stress measurement techniques were used, namely (1) direct yield stress measurement with the vane method and (2) indirect yield stress measurement with the slump test method. The correlation between these two methods was investigated as a secondary objective of this study. It was concluded that the suspension pH strongly influences the degree of microscopic particle interaction of the vehicle component and that manipulation of the suspension pH could move the material between interactive and noninteractive states. It was further concluded that increasing load mass percentage leads to a significant increase in the co-disposed material yield stress. It is believed that the load component mainly affects the co-disposed material yield stress through its contribution to the total solids concentration, which in turn results in an exponential increase in the material yield stress. The findings of this study showed remarkable flexibility in the manipulation of the various input parameters to produce the same yield stress value. It is therefore now possible to maintain a constant yield stress value as required by the environmental depositional requirements through various combinations of the input parameters and so keep the integrity of the deposition site intact. The correlation obtained in this study between the vane and slump test yield stress measurement techniques was fairly poor. The slump test only provided an accurate prediction of the yield stress when the material was in a highly interactive state. It is recommended that future research focuses on the thixotropic nature of the vehicle component as a function of suspension pH, the accuracy of the correlation between the vane and slump measured yield stress and the effect of the load on the bulk rheology of the co-disposed material.

In South Africa, being the second largest global coal exporter, coal mining plays a pivotal role in the growth of our economy, as well as supplying our nation’s ever increasing electricity needs; while also accounting for more than 10% of the 20 x 109 m3 water used annually in the country. Coal mining may thus be classified as a large-scale water user; known to inevitably generate wastewater [acid mine drainage (AMD)] and other waste material, including fly ash (FA). Current and conventional AMD treatment technologies include precipitation–aggregation (coagulation/flocculation) – settling as hydroxides or insoluble salts. The process stream resulting from these precipitation processes is still highly saline, therefore has to undergo secondary treatment. The best available desalination techniques include reverse osmosis (RO), electro dialysis (ED), ion exchange and evaporation. All available treatment methods associated with raw AMD and its derived process stream fall prey to numerous drawbacks. The result is that treatment is just as costly as the actual coal extraction. In addition, remediation only slows the problem down, while also having a short lifespan. Research conducted into converting fly ash, an otherwise waste material, into a marketable commodity has shown that direct mixing of known ratios of FA with AMD to a pre-determined pH, erves a dual purpose: the two wastes (AMD and FA) could be neutralized and produced a much cleaner water (secondary co-disposal [FA/AMD]-process water), broadly comparable to the process water derived from precipitation-aggregation treated AMD. The collected post process solid residues on the other hand, could be used for production of high capacity ion exchange material (e.g. zeolite A, faujasite, zeolite P, etc.). The produced ion exchange material can subsequently be utilized for the attenuation of metal species in neutralized FA/AMDprocess waters. / Magister Scientiae - MSc

The current study therefore aims to provide a comprehensive characterisation of weathered dry disposed ash cores, to reveal mobility patterns of chemical species as a function of depth and age of ash, with a view to assessing the potential environmental impacts. Fifty-nine samples were taken from 3 drilled cores obtained respectively from the 1 year, 8 year and 20-year-old sections of sequentially dumped, weathered, dry disposed ash in an ash dump site at Tutuka - a South African coal burning power station.

<p>The management and disposal of huge volumes of coal combustion by products such as fly ash has constituted a major challenge to the environment. In most cases due to the inadequate alternative use of coal fly ash, the discarded waste is stored in holding ponds, slag heaps, or stock piled in ash dumps. This practice has raised concerns on the prospect of inorganic metals release to the surface and groundwater in the vicinity of the ash dump. Acceptable scientific studies are lacking to determine the best ash disposal practices. Moreover, knowledge about the mobility patterns of inorganic species as a function of mineralogical association or pH susceptibility of the dry disposed ash dump under natural weathering conditions are scarce in the literature. Fundamental understanding of chemical interactions of dry disposed ash with ingressed CO2 from atmosphere, percolating rain water and brine irrigation within ash disposal sites were seen as key areas requiring investigation. The mineralogical association of inorganic species in the dry disposed ash cores can be identified and quantified. This would provide a basis for understanding of chemical weathering, mineralogical transformations or mobility patterns of these inorganic species in the dry ash disposal scenario. The current study therefore aims to provide a comprehensive characterisation of weathered dry disposed ash cores, to reveal mobility patterns of chemical species as a function of depth and age of ash, with a view to assessing the potential environmental impacts. Fifty-nine samples were taken from 3 drilled cores obtained respectively from the 1 year, 8 year and 20-year-old sections of sequentially dumped,&nbsp / weathered, dry disposed ash in an ash dump site at Tutuka - a South African coal burning power station. The core samples were characterized using standard analytical procedures viz: X-ray fluorescence (XRF), X-ray diffraction (XRD), Fourier transforms infrared (FTIR) techniques, Scanning electron microscopy/energy dispersive spectroscopy (SEM/EDS) and Acid neutralisation capacity (ANC) test. A modified sequential extraction (SE) method was used in this study. The chemical partitioning, mobility and weathering patterns in 1 year, 8 year and 20-year-old sections of the ash dump were respectively investigated using this modified sequential extraction scheme. The sequence of the extractions was as follows: (1) water soluble, (2) exchangeable, (3) carbonate, (4) iron and manganese and (5) residual. The results obtained from the 5 steps sequential extraction scheme were validated with the total metal content of the original sample using mass balance method. The distribution of major and trace elements in the different liquid fractions obtained after each step of sequential extraction of the 59 drilled core samples was determined by inductively coupled plasma mass spectrometry (ICPMS). The data generated for various ash core samples were explored for the systematic analysis of mineralogical transformation and change in ash chemistry with ageing of the ash. Furthermore, the data was analyzed to reveal the impact of ingressed CO2 from atmosphere, infiltrating rain water and brine irrigation on the chemistry of ash core samples. Major mineral phases in original ash core samples prior to extraction are quartz (SiO2) and mullite (3Al2O3&middot / 2SiO2). Other minor mineral phases identified were hematite (Fe2O3), calcite (CaCO3), lime (CaO), anorthite (CaAl2Si2O8), mica (Ca (Mg, Al)3 (Al3Si) O10 (OH)2), and enstatite (Mg2Si2O6). X-ray diffraction results show significant loss of crystallinity in the older ash cores. The presence of minor phases of calcite and mica in dry disposed ash cores are attributed to reduction in the pore water pH due to hydration, carbonation and pozzolanic reactions. The X-ray diffraction technique was unable to detect Fe-oxyhydroxide phase and morealuminosilicate phases in ash core samples due to their low abundance and amorphous character. X-ray fluorescence results of the original ash core samples showed the presence of major oxides, such as SiO2, Al2O3, Fe2O3, while CaO, K2O, TiO2, Na2O, MnO, MgO, P2O5, and SO3 occur in minor concentrations. The ratio of SiO2/Al2O3 classified the original core samples prior to extraction as a silico-aluminate class F fly ash. The ternary plot of major elements in 1-year-old ash core samples was both sialic and ferrocalsialic but 8 year and 20-year-old ash core samples were sialic in chemical composition. It is noteworthy that the mass % of SiO2 varies through the depth of the core with an increase of nearly 3 %, to 58 mass % of SiO2 at a depth of 6 m in the 1-year-old core whereas in the case of the 8-year-old core a 2 % increase of SiO2 to a level of 57.5 mass % can be observed at levels between 4-8 m, showing dissolution of major components in the matrix of older ash cores.. The Na2O content of the Tutuka ash cores was low and varied between 0.6-1.1 mass % for 1-year-old ash cores to around 0.6-0.8 mass % for 8-year-old ash cores. Sodium levels were higher in 1-year-old ash cores compared to 8 year and 20-year-old ashcores. Observed trends indicate that quick weathering of the ash (within a year) leached out Na+ from the ash dump. No evidence of Na+ encapsulation even though the ash dump was brine irrigated. Thus the dry disposal ash placement method does not result in a sustainable salt sink for Na-containing species over time. The total content of each of the elements in 1 year and 20-year-old ash cores was normalised with their total content in fresh ash from same power station to show enrichment and depletion factor. Major elements such as K+, Mn showed enrichment in 1-year-old ash cores whereas Al, Si, Na+, Ti, Ca, Mg, S and Fe showed depletion due to over time erosion. Trace elements such as Cr, Sr, P, Ba, Pb, V and Zn showed enrichment but Ni, Y, Zr showed depletion attributed to over time erosion. In 20-year-old ash cores, major elements such as Al, Na+ and Mn showed enrichment while Si, K+, Fe, Mg and Ca showed depletion highlighting their mobility. Trends indicated intensive flushing of major soluble components such as buffering constituents (CaO) by percolating rain water. The 1-year-old and 20-year-old coal ash cores showed a lower pH and greater loss/depletion of the soluble buffering constituents than the 2-week-old placed ash, indicating significant chemical weathering within a year. Based&nbsp / on ANC results the leaching behaviours of Ca, Mg, Na+, K+, Se, Cr, and Sr were found to be controlled by the pH of the leachant indicating high mobility of major soluble species in the ash cores when in contact with slightly acid rain water. Other investigated toxic metals such as As, Mo and Pb showed amphoteric behaviour with respect to the pH of the leachant. Chemical alterations and formation of transient minor secondary mineral phases was found to have a significant effect on the acid susceptibility and depletion pattern of chemical species in the core ash samples when compared to fresh ash. These ANC results correlated well with the data generated from the sequential extraction scheme. Based on sequential extraction results elements, showed noticeable mobility in the water soluble, exchangeable and carbonate fractions due to adsorption and desorption caused by variations in the pore water pH. In contrast, slight mobility of elements in the Fe and Mn, and residual fractions of dry disposed fly ashes are attributed to the co-precipitation and dissolution of minor amount of less soluble secondary phase overtime. The 1-year-old dry disposed ash cores were the least weathered among the 3 drilled ash cores. Therefore low concentration of toxic metals in older ash cores were ascribed to extensive weathering with slower release from residual mineral phases over time. Elements were found to associate with different mineral phases depending on the age or depth of the core samples showing greater heterogeneity in dispersion. For instance the average amount of total calcium in different mineral associations of 1-year-old ash cores is as follows / water soluble (10.2 %), exchangeable (37.04 %), carbonate (37.9 %), Fe and Mn (7.1 %) and residual (2.97 %). The amount of total Na+ in different mineral phases of 1-year-old ash cores followed this trend: water soluble (21 %), exchangeable (11.26 %), carbonate (2.6 %), Fe and Mn (4.7 %) and residual (53.9 %). The non-leachable portion of the total Na+ content (namely that contained in the residual fraction) in the 1-year-old ash core samples under conditions found in nature ranged between 5-91 %. This non-leachable portion of the Na+ showed the metastability of the mineral phases with which residual Na+ associates. Results showed older ash cores are enriched in toxic elements. Toxic elements such as As, B, Cr, Mo and Pb are enriched in the residual fraction of older ash cores. For instance As concentration in the residual fraction varied between 0.0003- 0.00043 mg kg-1 for 1-year-old ash cores to around 0.0003-0.0015 mg kg-1 for 20-year-old ash cores. This suggests that the older ash is enriched in toxic elements hence dust from the ash dump would be toxic to human health. The knowledge of mobility and ecotoxicological significance of coal fly ash is needed when considering its disposal or reuse in the environment. The mobility and ecotoxicology of inorganic metals in coal fly ash are determined by (i) mineralogical associations of inorganic species (ii) in-homogeneity in the ash dumps (iii) long and short term exposure to ingress CO2 and percolating rain water. Management issues such as inconsistent placement of ash in the dumps, poor choice of ash dump site, in-homogeneity in brine irrigation, no record of salt load put on the ash dumps and lack of proper monitoring requires improvement. The thesis provides justification for the use of the modified sequential extraction scheme as a predictive tool and could be employed in a similar research work. This thesis also proved that the dry ash disposal method was not environmental friendly in terms of overall leaching potential after significant chemical weathering. Moreover the study proved that the practice of brine co-disposal or irrigation on ash dumps is not sustainable as the ash dump did not act as a salt sink.</p>

<p>The management and disposal of huge volumes of coal combustion by products such as fly ash has constituted a major challenge to the environment. In most cases due to the inadequate alternative use of coal fly ash, the discarded waste is stored in holding ponds, slag heaps, or stock piled in ash dumps. This practice has raised concerns on the prospect of inorganic metals release to the surface and groundwater in the vicinity of the ash dump. Acceptable scientific studies are lacking to determine the best ash disposal practices. Moreover, knowledge about the mobility patterns of inorganic species as a function of mineralogical association or pH susceptibility of the dry disposed ash dump under natural weathering conditions are scarce in the literature. Fundamental understanding of chemical interactions of dry disposed ash with ingressed CO2 from atmosphere, percolating rain water and brine irrigation within ash disposal sites were seen as key areas requiring investigation. The mineralogical association of inorganic species in the dry disposed ash cores can be identified and quantified. This would provide a basis for understanding of chemical weathering, mineralogical transformations or mobility patterns of these inorganic species in the dry ash disposal scenario. The current study therefore aims to provide a comprehensive characterisation of weathered dry disposed ash cores, to reveal mobility patterns of chemical species as a function of depth and age of ash, with a view to assessing the potential environmental impacts. Fifty-nine samples were taken from 3 drilled cores obtained respectively from the 1 year, 8 year and 20-year-old sections of sequentially dumped,&nbsp / weathered, dry disposed ash in an ash dump site at Tutuka - a South African coal burning power station. The core samples were characterized using standard analytical procedures viz: X-ray fluorescence (XRF), X-ray diffraction (XRD), Fourier transforms infrared (FTIR) techniques, Scanning electron microscopy/energy dispersive spectroscopy (SEM/EDS) and Acid neutralisation capacity (ANC) test. A modified sequential extraction (SE) method was used in this study. The chemical partitioning, mobility and weathering patterns in 1 year, 8 year and 20-year-old sections of the ash dump were respectively investigated using this modified sequential extraction scheme. The sequence of the extractions was as follows: (1) water soluble, (2) exchangeable, (3) carbonate, (4) iron and manganese and (5) residual. The results obtained from the 5 steps sequential extraction scheme were validated with the total metal content of the original sample using mass balance method. The distribution of major and trace elements in the different liquid fractions obtained after each step of sequential extraction of the 59 drilled core samples was determined by inductively coupled plasma mass spectrometry (ICPMS). The data generated for various ash core samples were explored for the systematic analysis of mineralogical transformation and change in ash chemistry with ageing of the ash. Furthermore, the data was analyzed to reveal the impact of ingressed CO2 from atmosphere, infiltrating rain water and brine irrigation on the chemistry of ash core samples. Major mineral phases in original ash core samples prior to extraction are quartz (SiO2) and mullite (3Al2O3&middot / 2SiO2). Other minor mineral phases identified were hematite (Fe2O3), calcite (CaCO3), lime (CaO), anorthite (CaAl2Si2O8), mica (Ca (Mg, Al)3 (Al3Si) O10 (OH)2), and enstatite (Mg2Si2O6). X-ray diffraction results show significant loss of crystallinity in the older ash cores. The presence of minor phases of calcite and mica in dry disposed ash cores are attributed to reduction in the pore water pH due to hydration, carbonation and pozzolanic reactions. The X-ray diffraction technique was unable to detect Fe-oxyhydroxide phase and morealuminosilicate phases in ash core samples due to their low abundance and amorphous character. X-ray fluorescence results of the original ash core samples showed the presence of major oxides, such as SiO2, Al2O3, Fe2O3, while CaO, K2O, TiO2, Na2O, MnO, MgO, P2O5, and SO3 occur in minor concentrations. The ratio of SiO2/Al2O3 classified the original core samples prior to extraction as a silico-aluminate class F fly ash. The ternary plot of major elements in 1-year-old ash core samples was both sialic and ferrocalsialic but 8 year and 20-year-old ash core samples were sialic in chemical composition. It is noteworthy that the mass % of SiO2 varies through the depth of the core with an increase of nearly 3 %, to 58 mass % of SiO2 at a depth of 6 m in the 1-year-old core whereas in the case of the 8-year-old core a 2 % increase of SiO2 to a level of 57.5 mass % can be observed at levels between 4-8 m, showing dissolution of major components in the matrix of older ash cores.. The Na2O content of the Tutuka ash cores was low and varied between 0.6-1.1 mass % for 1-year-old ash cores to around 0.6-0.8 mass % for 8-year-old ash cores. Sodium levels were higher in 1-year-old ash cores compared to 8 year and 20-year-old ashcores. Observed trends indicate that quick weathering of the ash (within a year) leached out Na+ from the ash dump. No evidence of Na+ encapsulation even though the ash dump was brine irrigated. Thus the dry disposal ash placement method does not result in a sustainable salt sink for Na-containing species over time. The total content of each of the elements in 1 year and 20-year-old ash cores was normalised with their total content in fresh ash from same power station to show enrichment and depletion factor. Major elements such as K+, Mn showed enrichment in 1-year-old ash cores whereas Al, Si, Na+, Ti, Ca, Mg, S and Fe showed depletion due to over time erosion. Trace elements such as Cr, Sr, P, Ba, Pb, V and Zn showed enrichment but Ni, Y, Zr showed depletion attributed to over time erosion. In 20-year-old ash cores, major elements such as Al, Na+ and Mn showed enrichment while Si, K+, Fe, Mg and Ca showed depletion highlighting their mobility. Trends indicated intensive flushing of major soluble components such as buffering constituents (CaO) by percolating rain water. The 1-year-old and 20-year-old coal ash cores showed a lower pH and greater loss/depletion of the soluble buffering constituents than the 2-week-old placed ash, indicating significant chemical weathering within a year. Based&nbsp / on ANC results the leaching behaviours of Ca, Mg, Na+, K+, Se, Cr, and Sr were found to be controlled by the pH of the leachant indicating high mobility of major soluble species in the ash cores when in contact with slightly acid rain water. Other investigated toxic metals such as As, Mo and Pb showed amphoteric behaviour with respect to the pH of the leachant. Chemical alterations and formation of transient minor secondary mineral phases was found to have a significant effect on the acid susceptibility and depletion pattern of chemical species in the core ash samples when compared to fresh ash. These ANC results correlated well with the data generated from the sequential extraction scheme. Based on sequential extraction results elements, showed noticeable mobility in the water soluble, exchangeable and carbonate fractions due to adsorption and desorption caused by variations in the pore water pH. In contrast, slight mobility of elements in the Fe and Mn, and residual fractions of dry disposed fly ashes are attributed to the co-precipitation and dissolution of minor amount of less soluble secondary phase overtime. The 1-year-old dry disposed ash cores were the least weathered among the 3 drilled ash cores. Therefore low concentration of toxic metals in older ash cores were ascribed to extensive weathering with slower release from residual mineral phases over time. Elements were found to associate with different mineral phases depending on the age or depth of the core samples showing greater heterogeneity in dispersion. For instance the average amount of total calcium in different mineral associations of 1-year-old ash cores is as follows / water soluble (10.2 %), exchangeable (37.04 %), carbonate (37.9 %), Fe and Mn (7.1 %) and residual (2.97 %). The amount of total Na+ in different mineral phases of 1-year-old ash cores followed this trend: water soluble (21 %), exchangeable (11.26 %), carbonate (2.6 %), Fe and Mn (4.7 %) and residual (53.9 %). The non-leachable portion of the total Na+ content (namely that contained in the residual fraction) in the 1-year-old ash core samples under conditions found in nature ranged between 5-91 %. This non-leachable portion of the Na+ showed the metastability of the mineral phases with which residual Na+ associates. Results showed older ash cores are enriched in toxic elements. Toxic elements such as As, B, Cr, Mo and Pb are enriched in the residual fraction of older ash cores. For instance As concentration in the residual fraction varied between 0.0003- 0.00043 mg kg-1 for 1-year-old ash cores to around 0.0003-0.0015 mg kg-1 for 20-year-old ash cores. This suggests that the older ash is enriched in toxic elements hence dust from the ash dump would be toxic to human health. The knowledge of mobility and ecotoxicological significance of coal fly ash is needed when considering its disposal or reuse in the environment. The mobility and ecotoxicology of inorganic metals in coal fly ash are determined by (i) mineralogical associations of inorganic species (ii) in-homogeneity in the ash dumps (iii) long and short term exposure to ingress CO2 and percolating rain water. Management issues such as inconsistent placement of ash in the dumps, poor choice of ash dump site, in-homogeneity in brine irrigation, no record of salt load put on the ash dumps and lack of proper monitoring requires improvement. The thesis provides justification for the use of the modified sequential extraction scheme as a predictive tool and could be employed in a similar research work. This thesis also proved that the dry ash disposal method was not environmental friendly in terms of overall leaching potential after significant chemical weathering. Moreover the study proved that the practice of brine co-disposal or irrigation on ash dumps is not sustainable as the ash dump did not act as a salt sink.</p>

The current study therefore aims to provide a comprehensive characterisation of weathered dry disposed ash cores, to reveal mobility patterns of chemical species as a function of depth and age of ash, with a view to assessing the potential environmental impacts. Fifty-nine samples were taken from 3 drilled cores obtained respectively from the 1 year, 8 year and 20-year-old sections of sequentially dumped, weathered, dry disposed ash in an ash dump site at Tutuka - a South African coal burning power station.

Philosophiae Doctor - PhD / The management and disposal of huge volumes of coal combustion by products such as fly ash has constituted a major challenge to the environment. In most cases due to the inadequate alternative use of coal fly ash, the discarded waste is stored in holding ponds, slag heaps, or stock piled in ash dumps. This practice has raised concerns on the prospect of inorganic metals release to the surface and groundwater in the vicinity of the ash dump. Acceptable scientific studies are lacking to determine the best ash disposal practices. Moreover, knowledge about the mobility patterns of inorganic species as a function of mineralogical association or pH susceptibility of the dry disposed ash dump under natural weathering conditions are scarce in the literature. Fundamental understanding of chemical interactions of dry disposed ash with ingressed CO2 from atmosphere, percolating rain water and brine irrigation within ash disposal sites were seen as key areas requiring investigation. The mineralogical association of inorganic species in the dry disposed ash cores can be identified and quantified. This would provide a basis for understanding of chemical weathering, mineralogical transformations or mobility patterns of these inorganic species in the dry ash disposal scenario. The current study therefore aims to provide a comprehensive characterisation of weathered dry disposed ash cores, to reveal mobility patterns of chemical species as a function of depth and age of ash, with a view to assessing the potential environmental impacts. Fifty-nine samples were taken from 3 drilled cores obtained respectively from the 1 year, 8 year and 20-year-old sections of sequentially dumped, weathered, dry disposed ash in an ash dump site at Tutuka - a South African coal burning power station. The core samples were characterized using standard analytical procedures viz: X-ray fluorescence (XRF), X-ray diffraction (XRD), Fourier transforms infrared (FTIR) techniques, Scanning electron microscopy/energy dispersive spectroscopy (SEM/EDS) and Acid neutralisation capacity (ANC) test. A modified sequential extraction (SE) method was used in this study. The chemical partitioning, mobility and weathering patterns in 1 year, 8 year and 20-year-old sections of the ash dump were respectively investigated using this modified sequential extraction scheme. The sequence of the extractions was as follows: (1) water soluble, (2) exchangeable, (3) carbonate, (4) iron and manganese and (5) residual. The results obtained from the 5 steps sequential extraction scheme were validated with the total metal content of the original sample using mass balance method. The distribution of major and trace elements in the different liquid fractions obtained after each step of sequential extraction of the 59 drilled core samples was determined by inductively coupled plasma mass spectrometry (ICPMS). The data generated for various ash core samples were explored for the systematic analysis of mineralogical transformation and change in ash chemistry with ageing of the ash. Furthermore, the data was analyzed to reveal the impact of ingressed CO2 from atmosphere, infiltrating rain water and brine irrigation on the chemistry of ash core samples. Major mineral phases in original ash core samples prior to extraction are quartz (SiO2) and mullite (Al2O3·2SiO2). Other minor mineral phases identified were hematite (Fe2O3), calcite (CaCO3), lime (CaO), anorthite (CaAl2Si2O8), mica (Ca (Mg, Al)3 (Al3Si) O10 (OH)2), and enstatite (Mg2Si2O6). X-ray diffraction results show significant loss of crystallinity in the older ash cores. The presence of minor phases of calcite and mica in dry disposed ash cores are attributed to reduction in the pore water pH due to hydration, carbonation and pozzolanic reactions. The X-ray diffraction technique was unable to detect Fe-oxyhydroxide phase and morealuminosilicate phases in ash core samples due to their low abundance and amorphous character. X-ray fluorescence results of the original ash core samples showed the presence of major oxides, such as SiO2, Al2O3, Fe2O3, while CaO, K2O, TiO2, Na2O, MnO, MgO, P2O5, and SO3 occur in minor concentrations. The ratio of SiO2/Al2O3 classified the original core samples prior to extraction as a silico-aluminate class F fly ash. The ternary plot of major elements in 1-year-old ash core samples was both sialic and ferrocalsialic but 8 year and 20-year-old ash core samples were sialic in chemical composition. It is noteworthy that the mass % of SiO2 varies through the depth of the core with an increase of nearly 3 %, to 58 mass % of SiO2 at a depth of 6 m in the 1-year-old core whereas in the case of the 8-year-old core a 2 % increase of SiO2 to a level of 57.5 mass % can be observed at levels between 4-8 m, showing dissolution of major components in the matrix of older ash cores.. The Na2O content of the Tutuka ash cores was low and varied between 0.6-1.1 mass % for 1-year-old ash cores to around 0.6-0.8 mass % for 8-year-old ash cores. Sodium levels were higher in 1-year-old ash cores compared to 8 year and 20-year-old ashcores. Observed trends indicate that quick weathering of the ash (within a year) leached out Na+ from the ash dump. No evidence of Na+ encapsulation even though the ash dump was brine irrigated. Thus the dry disposal ash placement method does not result in a sustainable salt sink for Na-containing species over time. The total content of each of the elements in 1 year and 20-year-old ash cores was normalised with their total content in fresh ash from same power station to show enrichment and depletion factor. Major elements such as K+, Mn showed enrichment in 1-year-old ash cores whereas Al, Si, Na+, Ti, Ca, Mg, S and Fe showed depletion due to over time erosion. Trace elements such as Cr, Sr, P, Ba, Pb, V and Zn showed enrichment but Ni, Y, Zr showed depletion attributed to over time erosion. In 20-year-old ash cores, major elements such as Al, Na+ and Mn showed enrichment while Si, K+, Fe, Mg and Ca showed depletion highlighting their mobility. Trends indicated intensive flushing of major soluble components such as buffering constituents (CaO) by percolating rain water. The 1-year-old and 20-year-old coal ash cores showed a lower pH and greater loss/depletion of the soluble buffering constituents than the 2-week-old placed ash, indicating significant chemical weathering within a year. Based on ANC results the leaching behaviours of Ca, Mg, Na+, K+, Se, Cr, and Sr were found to be controlled by the pH of the leachant indicating high mobility of major soluble species in the ash cores when in contact with slightly acid rain water. Other investigated toxic metals such as As, Mo and Pb showed amphoteric behaviour with respect to the pH of the leachant. Chemical alterations and formation of transient minor secondary mineral phases was found to have a significant effect on the acid susceptibility and depletion pattern of chemical species in the core ash samples when compared to fresh ash. These ANC results correlated well with the data generated from the sequential extraction scheme. Based on sequential extraction results elements, showed noticeable mobility in the water soluble, exchangeable and carbonate fractions due to adsorption and desorption caused by variations in the pore water pH. In contrast, slight mobility of elements in the Fe and Mn, and residual fractions of dry disposed fly ashes are attributed to the co-precipitation and dissolution of minor amount of less soluble secondary phase overtime. The 1-year-old dry disposed ash cores were the least weathered among the 3 drilled ash cores. Therefore low concentration of toxic metals in older ash cores were ascribed to extensive weathering with slower release from residual mineral phases over time. Elements were found to associate with different mineral phases depending on the age or depth of the core samples showing greater heterogeneity in dispersion. For instance the average amount of total calcium in different mineral associations of 1-year-old ash cores is as follows; water soluble (10.2 %), exchangeable (37.04 %), carbonate (37.9 %), Fe and Mn (7.1 %) and residual (2.97 %). The amount of total Na+ in different mineral phases of 1-year-old ash cores followed this trend: water soluble (21 %), exchangeable (11.26 %), carbonate (2.6 %), Fe and Mn (4.7 %) and residual (53.9 %). The non-leachable portion of the total Na+ content (namely that contained in the residual fraction) in the 1-year-old ash core samples under conditions found in nature ranged between 5-91 %. This non-leachable portion of the Na+ showed the metastability of the mineral phases with which residual Na+ associates. Results showed older ash cores are enriched in toxic elements. Toxic elements such as As, B, Cr, Mo and Pb are enriched in the residual fraction of older ash cores. For instance As concentration in the residual fraction varied between 0.0003- 0.00043 mg kg-1 for 1-year-old ash cores to around 0.0003-0.0015 mg kg-1 for 20-year-old ash cores. This suggests that the older ash is enriched in toxic elements hence dust from the ash dump would be toxic to human health. The knowledge of mobility and ecotoxicological significance of coal fly ash is needed when considering its disposal or reuse in the environment. The mobility and ecotoxicology of inorganic metals in coal fly ash are determined by (i) mineralogical associations of inorganic species (ii) in-homogeneity in the ash dumps (iii) long and short term exposure to ingress CO2 and percolating rain water. Management issues such as inconsistent placement of ash in the dumps, poor choice of ash dump site, in-homogeneity in brine irrigation, no record of salt load put on the ash dumps and lack of proper monitoring requires improvement. The thesis provides justification for the use of the modified sequential extraction scheme as a predictive tool and could be employed in a similar research work. This thesis also proved that the dry ash disposal method was not environmental friendly in terms of overall leaching potential after significant chemical weathering. Moreover the study proved that the practice of brine co-disposal or irrigation on ash dumps is not sustainable as the ash dump did not act as a salt sink. / South Africa