This diploma thesis is concerned with simulation of elastohydrodynamic lubrication of point contacts using the finite element method. The first part of the thesis focuses on the study of the issue and introduces equations for model creation and numerical methods which can be used for EHD calculation. The most suitable solution approach has been chosen from the overview, namely the Full system approach. The software we chose for applying the method was COMSOL Multyphysics. The following part of the thesis deals with model’s creation and gives its elaborate description. We introduce models for calculation of line and point EHD lubrication for newtonian lubricants and, last but not least, we also present a model for calculation of point contact EHD lubrication for non-newtonian lubricants. The next part of the thesis then verifies all the models. That is achieved by comparing the calculated results to results from different papers. The conclusive part of the thesis then examines the matches of acquired results to different prediction relationships and experiments.

Master’s thesis deals with development of software application to calculate contact pressure in eleastohydrodynamic lubricated contact in order to use previously obtained data of the lubricating film thickness. The introduction contains a short overview of methods used for the study of film thickness and contact pressure. Custom work includes a contact pressure solution derived from a film thickness, a description of the developed software and analysis of algorithms used for its compilation. The last part deals with the verification of algorithm, application of software for calculating the contact pressure on the rough surface and analysis of the results. The conclusion includes a summary and possible application of software in practice.

The purpose of this thesis is to reveal production mechanisms of lubrication films between non-conformal surfaces in situations, when is not possible to designate lubrication regime as fully flooded elastohydrodynamic contact. Under certain conditions of lubrication volume, rolling speeds, temperatures, lubrication properties or loads could lubrication film decrease under values determined by fully flooded formulas. This regime is designated as starvation at it includes risk of increased wear. In this thesis the methodology and the new simulator of starving contact are described. Obtained film thickness results are compared with existing numerical models.

This diploma thesis deals with experimental study of the effect of surface grooves on distribution of lubricant film in elastohydrodynamic lubricated point contact. Lubricant film thickness was measured by ball-on-disc apparatus using an optical interferometry technique - thin film colorimetric interferometry. The effects of groove geometry, lubricant and operating conditions were studied in this diploma thesis. The effects of these variables are evaluated based on newly suggested parameter Rgi (groove influence ratio). Groove influence ratio is defined as an influenced film thickness influenced by groove divided by film thickness for smooth surfaces.

This diploma thesis deals with the study of film formation in compliant contact. Primary attention is dedicated to the influence of the entrainment speed and slide-to-roll ratio (SRR) on the central film thickness. Based on a research study of the available experimental methods, the fluorescence microscopy was used to achieve the aim of the work. Experiments were realized in ball-on-disk configuration. Firstly, a validation of the method was performed where the solid contact of the ceramic ball and the glass disk was analyzed. Since the measured values were in a good agreement with the theoretical prediction, a ball of NBR rubber material, which is commonly used for production of lip seals and o-rings, was subsequently used. The experimental measurements were performed under pure rolling and rolling/sliding conditions when the entrainment speeds varied in the range from 10 to 400 mm / s. A constant load of 0.2 N was applied. The measured data were then compared to the theoretical predictions for compliant contacts. The results showed that the thickness of the lubricating film gradually increases with increasing entrainment speed, which corresponds to theoretical assumption. Against expectations, evident influence of SRR on the film formation has been observed. In the last part of the thesis the measured data are confronted with previously published studies. Finally, some limitations of this study are discussed and recommendations for further improvement of the used experimental method are suggested.

Disertační práce se zabývá chováním a odezvou elastohydrodynamického (EHD) mazacího filmu za neustálených provozních podmínek. V úvodní části práce jsou shrnuty poznatky z oblasti EHD mazání; od jeho historie, přes základní mechanismy mazání a používané experimentální metody, až po nedávno publikované studie zaměřené na transientní podmínky. Hlavním cílem práce bylo experimentálně objasnit vliv provozních parametrů a reologických vlastností maziv na chování mazacího filmu v bodovém kontaktu při jeho nárazovém zatěžování a vystavení příčným vibracím. Za tímto účelem byla vyvinuta laboratorní zařízení umožňující měření rozložení mazacího filmu a tření za kontrolovaných nestacionárních podmínek. Experimenty odhalili zásadní roli přibližovacích a zatěžovacích rychlostí na formování stlačených mazacích filmů při nárazovém zatěžování. Výsledky byly srovnávány s nedávným teoretickým řešením. Bylo ukázáno na jeho nedostatky, jež byly následně odstraněny implementací empirických vztahů zohledňujících reologii maziv. V případě příčných vibrací byly nalezeny hranice selhání mazacího filmu a určeny vztahy popisující vliv příčných vibrací na centrální tloušťku filmu a její fluktuace jednotně pro všechny maziva. Závěrečná část práce poskytuje nový pohled na reologii maziv pomocí inovativního přístupu měření třecích reakcí maziva současně ve dvou směrech kontaktu za podmínek příčných vibrací. Tyto původní výsledky rozšiřují pochopení mechanizmů EHD mazání a mohou být použity k dokonalejším návrhům strojů, a vylepšit tak jejich účinnost, spolehlivost a životnost.

The diploma thesis deals with the analysis of the effects surface texturing on starved contact. Experimental verification was realized on apparatus simulating contact between a steel ball and glass disc using colorimetric interferometry and high-speed camera. The work deals with lubrication regimes, problems with starved contacts and surface texturing which can reduce effects of starvation on non-conformal surface contacts.

This work deals with construction of an experimental measuring stand. This stand will be used for research focused on wheel flange lubrication improvement. The construction is based on wheel flange lubrication system Tribotec OK-02. First part treats of rail vehicle dynamics and wheel flange lubrication problematics, second part describes construction itself.

This diploma thesis deals with the proposal of methodology for film thickness eva- luation within compliant contacts. With respect to characteristics of such contact pairs, like variable film thickness, high surface roughness, or poor conductivity and reflectivity, the usage of conventional experimental methods is particularly complicated. In present study, an optical method based on the principle of fluo- rescent microscopy was employed in present thesis. An evaluation algorithm in- volving background normalization and calibration of fluorescent intensity to film thickness was created in a form of experimental software. The proposed algori- thm was validated by using elastohydrodynamic contact formed between ceramic ball and glass disc. The measured film thickness was compared with theoretical prediction, while very good agreement of obtained data was observed. Further, a series of experiments with compliant samples was conducted, while the central film thickness was evaluated as a function of mean speed, applied lubricant, ap- plied load and slide-to-roll ratio. The last part of the thesis is focused on results analysis and discussion considering the previously published literature.

This PhD thesis deals with elastohydrodynamic lubrication (EHL) under the conditions that occur between mated hypoid gear teeth. The aim is to describe experimentally the behaviour of lubricating film and mechanisms of its formation. The focus is mainly placed on clarifying the influence of direction and magnitude of sliding velocity in circular and elliptical contacts. Generally, it is still assumed that the direction of sliding velocity has no effect on the resulting lubricant film. In this study optical interferometry is used to determine distribution of lubricant film thickness. This work includes new and original results which clarify the studied problem. It was found that the direction of sliding velocity affects shape of the film at high speeds. This relates to the effect on heat flow through the contact. The results have an impact on the development of general EHL theory and provide knowledge applicable in film thickness prediction in the design of real tribological nodes.