The goal of this dissertation is to evaluate the effectiveness of model predictive control (MPC) for a magnetically suspended flywheel energy storage uninterruptible power supply (FlyUPS). The reason this research topic was selected was to determine if an advanced control technique such as MPC could perform better than a classical control approach such as decentralised Proportional-plus-Differential (PD) control. Based on a literature study of the FlyUPS system and the MPC strategies available, two MPC strategies were used to design two possible MPC controllers were designed for the FlyUPS, namely a classical MPC algorithm that incorporates optimisation techniques and the MPC algorithm used in the MATLAB® MPC toolbox™. In order to take the restrictions of the system into consideration, the model used to derive the controllers was reduced to an order of ten according to the Hankel singular value decomposition of the model. Simulation results indicated that the first controller based on a classical MPC algorithm and optimisation techniques was not verified as a viable control strategy to be implemented on the physical FlyUPS system due to difficulties obtaining the desired response. The second controller derived using the MATLAB® MPC toolbox™ was verified to be a viable control strategy for the FlyUPS by delivering good performance in simulation. The verified MPC controller was then implemented on the FlyUPS. This implementation was then analysed in order to validate that the controller operates as expected through a comparison of the simulation and implementation results. Further analysis was then done by comparing the performance of MPC with decentralised PD control in order to determine the advantages and limitations of using MPC on the FlyUPS. The advantages indicated by the evaluation include the simplicity of the design of the controller that follows directly from the specifications of the system and the dynamics of the system, and the good performance of the controller within the parameters of the controller design. The limitations identified during this evaluation include the high computational load that requires a relatively long execution time, and the inability of the MPC controller to adapt to unmodelled system dynamics. Based on this evaluation MPC can be seen as a viable control strategy for the FlyUPS, however more research is needed to optimise the MPC approach to yield significant advantages over other control techniques such as decentralised PD control. / Thesis (MIng (Computer and Electronic Engineering))--North-West University, Potchefstroom Campus, 2013

Master’s thesis deals with the design of the drive of the press LKJP 630, the configuration is a fixed range by the construction of LKJP. The thesis was ordered by partnership with company ŽĎAS, which is introduced. The first part is devoted to analysis of solved problems, it primarily contains the overview on forming machines, used drives and a description of their main parts. The second part deals with the drive itself, there is accomplished the design and performed the strength analysis of the major parts of the drive. Drawing documentation and bill of materials are included.

When performing a biomechanical analysis of human movement, knowledge about the ground reaction force (GRF) is necessary to compute forces and moments within joints. This is important when analysing a movement and its effect on the human body. To obtain knowledge about the GRF, the gold standard is to use force plates which directly measure all three components of the GRF (mediolateral, anteroposterior and normal). However, force plates are heavy, clunky and expensive, setting constraints on possible experimental setups, which make it desirable to exclude them and instead use a predictive method to obtain the full GRF. Several predictive methods exist. The node model is a GRF predictive method included in a musculoskeletal modeling software. The tool use motion capture and virtual actuators to predict all three GRF components. However, this model has not yet been validated during weighted leg press and weighted squat. Furthermore, the normal component of the GRF can be measured continuously during the activity with pressure sensitive insoles (PSIs), which might provide better accuracy of the GRF prediction. The objectives of this thesis were to investigate whether force plates can be exluded during weighted leg press and weighted squat and to investigate whether PSIs can improve the GRF prediction. To investigate this, the node model and a developed shear model was validated. The shear model computes the two shear GRF components based on data from PSIs, an external load acting upon the body and data from a motion capture system. Both the node model and the shear model were analysed with two test subjects performing two successive repetitions of both weighted squat and weighted leg press in a flywheel exercise device. During the leg press exercise, the node model had a mean coeffcient of correlation (Pearson's) ranging from 0.70 to 0.98 for all three directions with a mean root mean square error ranging between 8 % to 20 % of the test person's body weight. The developed shear model had a coeffcient of correlation (Pearson's) between 0.64 to 0.99 and a mean root mean square error between 3 % and 21 % of the test person's body weight. This indicates that it is possible to exclude force plates and instead predict the GRF during weighted leg press. During squat, neither the node model nor the shear model provided accurate results regarding the mediolateral and anteroposterior components of the GRF, suggesting that force plates can not yet be excluded to obtain the full GRF during weighted squat. The results of the normal component during leg press was somewhat improved with the shear model compared to the node model, indicating that using PSIs can improve the results to some extent.

No description available.

Measuring lower limb strength and symmetry is a common practice in elite sports to determine the return to sports point in time during rehabilitation, and this information could be useful for amateur athletes too. However, the devices used for this are highly sophisticated and hardly accessible. The aim of this project is to devise an affordable system for lower limb strength measurement which can be integrated with a common training system, to make this type of information widely available. The system is built up on a flywheel-based leg extension machine (LegExx by Exxentric AB) that allows quadriceps training at maximal force in concentric and eccentric contraction. Inexpensive standard components and software were used for prototyping. The parameters of interest were angular velocity of extension/flexion in the knee and force applied by the athlete. In the first step, evaluation was limited to the concentric phase of movement. Angular velocity and leg position was measured with a gyroscope sensor (Movesense by Suunto). For force measurement, two approaches were tested: In prototype A, the tension of the drive belt, which ultimately puts the flywheel into rotation, was measured with a sensor for tensile forces (Tindeq Progressor 300). In prototype B, a more direct measurement was used, with force sensors mounted under the contact point of the athlete’s shank with the swing beam of the LegExx. Sensor data were transmitted via Bluetooth to a mobile device or a laptop and displayed graphically after synchronization of the data streams. Force values were converted to torque using inverse kinematics to make the two prototypes comparable. The first prototypes were shown to be workable and yielded similar readings for concentric peak torque, with realistic wave forms in the graphical display. Comparison with results of a gold standard isokinetic dynamometer revealed, however, major discrepancies mainly regarding the absolute torque values. Oscillation in the belt system were identified as an issue in prototype A, while cross talk between sensors and vulnerability to leg placement occurred in prototype B. However, these issues are not insurmountable, and it is suggested to proceed with the development of prototype B, as it has the advantage of simultaneous measurement and direct comparison of both legs. / Att mäta styrka och symmetri i nedre extremiteterna är vanligt inom elitidrott för att avgöra när man kan återgå till idrottsutövning under rehabiliteringen, och denna information kan vara användbar även för amatöridrottare. De apparater som används för detta är dock mycket sofistikerade och svårtillgängliga. Syftet med detta projekt är att utforma ett prisvärt system för mätning av styrkan i nedre extremiteterna som kan integreras med ett vanligt träningssystem, för att göra denna typ av information allmänt tillgänglig. Systemet är uppbyggt på en svänghjulsbaserad benspark maskin (LegExx från Exxentric AB) som möjliggör quadriceps träning vid maximal kraft i koncentrisk och excentrisk kontraktion. Kostnadseffektiva standardkomponenter och mjukvara användes för prototypframställning. De parametrar som var av intresse var vinkelhastighet för utsträckning- /böjning i knäet och den kraft som utövades av idrottaren. I det första steget begränsades utvärderingen till rörelsens koncentriska fas. Vinkelhastighet och benposition mättes med en gyroskopisk sensor (Movesense från Suunto). För kraftmätning testades två tillvägagångssätt: I prototyp A mättes dragkraften i drivremmen, som i slutändan sätter svänghjulet i rotation, med en sensor för dragkrafter (Tindeq Progressor 300). I prototyp B användes en mer direkt mätning med kraftsensorer som monterades under kontaktpunkten mellan idrottsutövarens smalben och LegExx:s svängbalk. Sensordata överfördes via Bluetooth till en mobil enhet eller en bärbar dator och visades grafiskt efter synkronisering av dataströmmarna. Kraftvärden omvandlades till vridmoment med hjälp av invers kinematik för att göra de två prototyperna jämförbara. De första prototyperna visade sig fungera och gav liknande mätningar för koncentriskt toppmoment, med realistiska vågformer i den grafiska displayen. En jämförelse med resultaten från en isokinetisk dynamometer med guldstandard visade dock på stora skillnader, främst när det gäller de absoluta vridmomentvärdena. Oscillation i bältesystemet identifierades som ett problem i prototyp A, medan överkoppling mellan sensorer och känslighet för benplacering förekom i prototyp B. Dessa problem är dock inte oöverstigliga, och det föreslås att man fortsätter att utveckla prototyp B, eftersom den har fördelen av samtidig mätning och direkt jämförelse av båda benen.

This study deals with the process of building up the local congregation and the manner in which missional objectives are achieved. The study is undertaken against the background of the disturbing decline in membership numbers particularly in the two traditional Reformational churches in South Africa, namely the Dutch Reformed Church (DRC) and the Netherdutch Reformed Church of Africa. This decline is in line with similar tendencies in mainstream churches the world over. Collins’s (2006) three questions to the local congregation constitute the point of departure. Firstly: To what degree does the congregation function effectively in line with her mission in the world? Secondly: To what extent does the congregation make a distinct impact on the community? If the congregation were to disappear all of a sudden – will it leave a serious void in the community? The third question deals with sustainability: Is the congregation’s long term impact of such nature that its success is not just attributable to a single leader. The three questions have been adapted according to Collins’s process model (2001) and the key aspects of the theory of building up the local church are discussed in Chapters 2 and 3. The bulk of Chapter 2 deals with the very important matter of the missio Dei and discusses how the congregation should discover and enact her missional calling in the local community. The study furthermore deals with mission in the current South African context, particularly in view of the fact that an entirely new mission field has opened itself up with the influx into the country of so many people from neighboring countries who have come to live in our midst. Chapter 4 deals with the empirical testing associated with the study to establish if the study’s hypothesis, namely whether local churches that have undergone a structured process of building up the local church are missionally more successful than those that have not undergone a structured process, can be verified. The findings in this regard are dealt with in Chapter 5, while certain aspects that characterize the missional congregation in current times are also discussed. / Thesis (PhD)--University of Pretoria, 2010. / Practical Theology / unrestricted

Wave energy converter (WEC) harnesses energy from the ocean to produce electrical power. The electrical power produced by the WEC is fluctuating and is not maximized as well, due to the varying ocean conditions. As a consequence, without any intermediate power conversion stage, the output power from the WEC can not be fed into the grid. To feed WEC output power into the grid, a two-stage power conversion topology is used, where the WEC output power is first converted into DCpower through rectification, and then a DC-AC converter (inverter) is used to supply AC power into the grid. The main motive of this research is to extract maximum electrical power from the WEC by active rectification and smoothing the power fluctuation of the wave energy converter through a hybrid energy storage system consisting of battery and flywheel. This research also illustrates active and reactive power injection to the grid according to load demand through a voltage source inverter.

This diploma thesis is about the basics of satellite systems, about their sorting, usage and technologies. An important part is the description of the principles controlling and stabilization of the small experimental CubeSat type satellites. The main point is the proposition and construction of the laboratory model of the CubeSat type satellite that should simulate the chosen methods of controlling and stabilization in laboratory conditions. The thesis describes the construction of the electronic parts of the model, the controlling software of the satellite’s processor and user software for easy controlling by PC.

This master thesis deals with the development and construction of the inverted pendulum, inspired by the Cubli project. The objective is to develop and design an inverted pendulum, in the shape of one side of the cube balancing at one of its corner and for balancing is used the flywheel. For its design 3D printing is used to the maximum extent and as the electronic parts commonly available components at an affordable price are used. The design of the construction and the components allow the construction of a complete cube, without the need of further development or fundamental changes in the design of the model. For the calculations and the design of the controller the Matlab / Simulink software was used. As the controller algorithm the LQR algorithm is used with added integral feedback, to minimize control error. The 3D models of the single parts are created with FreeCAD software and printed on a 3D Prusa i3 MK2S printer.

Diploma thesis deals with design of a flywheel and a belt pulley of single toggle jaw crusher DCJ 900x600. The first part is dedicated to overview of the methods for calculation of a size of flywheels for working machines. The second part is focused on calculation of a size of the flywheel. The third part treats the constructional design of the flywheel. In the last two parts there is elaborated analysis of a changing size of the flywheel depended on increasing the working rotation speed and change of coefficient .