No description available.

A first-generation LaB6 heaterless hollow cathode with a flat-plate anode is experimentally investigated. The cathode is characterized using krypton as propellant at varying flow rates, discharge currents and cathode-anode distances. Voltage probes, used to make direct voltage measurements in the ignition circuit, are the only diagnostic tool used experimentally. A plasma model is used to infer plasma parameters in the cathode emitter region. The cathode characterization results are consistent with those obtained during previous investigations of 1 A-class LaB6 hollow cathode with krypton. A peak-to-peak anode voltage criterion is used to identify the discharge modes and the occurrence of mode transition. Fourier analysis of the keeper and anode voltage waveforms carried out to study the discharge mode behavior reveals resonant frequencies ranging from 40 to 150 kHz. Lastly, post-test visual observations of the cathode components show signs of emitter poisoning and keeper erosion. / Master of Science / Recent years have seen rapid growth in the development of both stand-alone satellites and satellite constellations. A critical component of these satellites is the on-board propulsion system, which is responsible for controlling their orientation with respect to the object of interest and keeping the spacecraft in the assigned orbit. Generally, electric propulsion systems are used for this purpose. These types of propulsion systems use electrical power to change the velocity of satellite, providing a small thrust for a long duration of time as compared to chemical propulsion systems. Certain types of electric thrusters utilize a hollow cathode device as an electron source to start-off and support the thruster operation. In this research, a non-conventional hollow cathode for low power applications is developed and tested. The main characteristic of the developed cathode is the heaterless configuration, which eliminates the heater module used in conventional cathodes to enable the cathode to reach its operational temperature. The absence of a heater reduces the complexity of the cathode and the electrical power system. The cathode utilizes an electron emitter material which is insensitive to impurities and air exposure. Additionally, unlike typical electric thrusters which use xenon as the fuel, this cathode uses krypton which is similar to xenon but is less expensive. The presented work includes an overview of electric propulsion and the hollow cathode operation, followed by a detailed discussion of the heaterless hollow cathode design, the experimental setup and the test results. Several noteworthy findings regarding cathode operation are included as well. This research shows that the non-conventional heaterless hollow cathode and its operation with krypton have the potential to improve the overall thruster performance by reducing the weight and the cost, thus contributing to an integral aspect of satellite on-board propulsion.

Thesis (M.S.)--University of Florida, 2004. / Title from title page of source document. Document formatted into pages; contains 41 pages. Includes vita. Includes bibliographical references.

The aim of this study was to produce zirconium diboride (ZrB2) and other metal borides such as lanthanum hexaboride (LaB6) and cerium hexaboride (CeB6) by magnesiothermic reduction (reaction of metal oxide, boron oxide and magnesium) using volume combustion synthesis (VCS) and mechanochemical process (MCP). Production of ZrB2 by VCS in air occurred with the formation of side products, Zr2ON2 and Mg3B2O6 in addition to MgO. Formation of Zr2ON2 was prevented by conducting VCS experiments under argon atmosphere. Wet ball milling was applied before leaching for easier removal of Mg3B2O6. Leaching in 5 M HCl for 2.5 hours was found to be sufficient for removal of MgO and Mg3B2O6. By MCP, 30 hours of ball milling was enough to produce ZrB2 where 10% of excess Mg and B2O3 were used. MgO was easily removed when MCP products were leached in 1 M HCl for 30 minutes. Complete reduction of ZrO2 could not be achieved in either production method because of the stability of ZrO2. Hence, after leaching VCS or MCP products, final product was composed of ZrB2 and ZrO2. Formation of LaB6 and CeB6 were very similar to each other via both methods. Mg3B2O6 appeared as a side product in the formation of both borides by VCS. After wet ball milling, products were leached in 1 M HCl for 15 hours and pure LaB6 or CeB6 was obtained. As in ZrB2 production, 30 hours of ball milling was sufficient to form these hexaborides by MCP. MgO was removed after leaching in 1 M HCl for 30 minutes and the desired hexaboride was obtained in pure form.

Thesis (Ph. D.)--University of Nevada, Reno, 2008. / "December 2008." Includes bibliographical references (leaves 161-173). Online version available on the World Wide Web.