Dans un contexte de diminution des émissions polluantes émises par les moteurs à combustion interne, le secteur des transports assiste à une amélioration des motorisations mais également à une diversification des carburants pour l’automobile. L’utilisation de ces différents carburants entraîne souvent un impact sur les performances de la combustion. Dans le cas du moteur à allumage commandé, la performance dépend du dégagement d’énergie, image de la vitesse de la combustion, soit du front de flamme consommant le mélange air-carburant. Or toute flamme en expansion est théoriquement soumise à des effets de courbure et de cisaillement, toutes deux contributions de l’étirement. La réponse à l’étirement étant propre à chaque type de mélange air-carburant (lié au carburant proprement dit, à la richesse du mélange, à la dilution …), ce travail de thèse est centré sur la compréhension de l’impact de l’étirement sur les performances des carburants dans les moteurs à allumage commandé. Pour cela, différents mélanges air-carburant similaires du point de vue des propriétés thermodynamiques et des vitesses fondamentales de combustion laminaire mais avec des sensibilités à l’étirement différentes ont été sélectionnés. Ces mélanges ont ensuite été étudiés dans différentes configurations expérimentales et à l’aide de différentes techniques de mesure: moteur monocylindre opaque et à accès optiques, chambre sphérique de combustion turbulente. Les résultats montrent que les propriétés de sensibilités à l’étirement déterminées en régime laminaire comme la longueur de Markstein et le nombre de Lewis sont indicatrices du comportement des mélanges en combustion turbulente, comme dans la chambre de combustion caractéristique des moteurs à allumage commandé, et sont des paramètres à prendre en considération afin de prédire les performances plus globales de ces carburants que ce soit expérimentalement qu’en simulation. / In a context of decreasing pollutant emissions, the transport sector is facing an improvement of engine concept as well as a fuel diversification. The use of these different fuels often involves an impact on the combustion performance itself. In the case of Spark ignition engine, the efficiency is a function of the released heat, image of the combustion speed, i.e. the flame front speed consuming the air-fuel mixture. It is well known that every expanding flame is submitted to flame curvature and strain rate which are both contributors to flame stretch. As the answer of each air-fuel mixture (i.e. the fuel itself, the equivalence ratio, the dilution …) is different to flame stretch, the objective of this work is to understand flame stretch impact on fuel performance in Spark-Ignition engines. To achieve this goal, different fuel-air mixtures with similar unstretched laminar burning speed and thermodynamic properties but different responses to stretch were selected. Those mixtures were then studied with different experimental devices with different measurement techniques: single-cylinder metallic and optical engines, turbulent combustion spherical vessel. Results show that flame stretch sensitivity properties such as Markstein length and Lewis number, determined in laminar combustion regime, are relevant parameters to describe the flame propagation in turbulent combustion as in the combustion chamber of the Spark-Ignition engine and need to be taken into consideration to evaluate global performance of these fuels, experimentally and also in modeling simulation.

[pt] Para substituir parcialmente a demanda em óleo diesel de origem fóssil, reduzir os elevados custos de importação e respeitar as normas ambientais, políticas sustentáveis já levaram a substituir parcialmente óleo diesel por biodiesel. Entretanto, outras tecnologias, como as misturas diesel-biodiesel-etanol, estão sendo investigadas. O principal desafio dessas misturas consiste em melhorar a miscibilidade e a estabilidade do álcool no óleo diesel. No presente trabalho, formulou-se um aditivo original, a partir de compostos renováveis, que permitiu melhorar a faixa de concentração de etanol anidro dentro de óleo diesel com 15 por cento em volume de biodiesel e de temperatura onde observa-se misturas estáveis. Diversas propriedades físico-químicas das misturas aditivadas foram medidas em uma larga faixa de concentração de etanol para avaliar os aspetos de consumo, qualidade da combustão, comportamento a baixa temperatura, interação entre fluido e superfície, e segurança. Os resultados obtidos mostraram que misturas com, pelo menos, 1,0 por cento em volume de aditivo e até 20 por cento em volume de etanol anidro são estáveis para temperaturas superiores a 10 graus Celsius e respeitam a maioria das especificações brasileiras atuais para óleo diesel. Ensaios experimentais em um motor de ignição por compressão MWM 4.10 TCA (Euro III) foram realizados com estas misturas. Os resultados obtidos mostraram que a substituição do óleo diesel altera as características da combustão: o crescente teor de etanol leva ao aumento do atraso de ignição, à liberação de calor mais rápida e à diminuição da pressão máxima. Mesmo nessas condições não otimizadas de injeção e de combustão, os resultados mostraram uma melhor conversão da energia química no etanol para produzir potência efetiva, comparado com os valores encontrados nos motores flex fuel de ciclo Otto, além de um pequeno aumento no rendimento térmico do motor. / [en] In order to partially replace the demand of fossil diesel fuels, to reduce high import costs and to comply with environmental standards, sustainable policies have led to partially replace diesel fuel by biodiesel. However, other technologies, such as diesel-biodiesel-ethanol mixtures, are being investigated. The major challenge of these mixtures is to improve the miscibility and the stability of alcohol in diesel fuel. In this study, an original additive, from renewable compounds, improved the miscibility of anhydrous ethanol in diesel fuel with 15 per cent by volume of biodiesel and temperature in which stable mixtures were observed. Several physicochemical properties of the additivated mixtures were measured in a large range of ethanol concentration to evaluate aspects of consumption, combustion quality, behavior at low temperature, interaction between the fluid and the surface, and safety. The results showed that blends with, at least 1.0 per cent, by volume of additive and 20 per cent by volume of anhydrous ethanol are stable at temperatures above 10 degrees Celsius and respected most of the current Brazilian specifications for diesel fuel. Experimental tests on a compression ignition engine MWM 4.10 TCA (Euro III) were performed with these mixtures. The results showed that the diesel fuel substitution alters the characteristics of combustion: the increased ethanol content implied an increase of the ignition delay, a faster heat release and a decrease of maximum pressure. Despite these non-optimized conditions for injection and combustion, results showed a better conversion of ethanol chemical energy into brake power, in comparison to the values found in flex fuel spark ignition engine, in addition to a small increase in the indicated efficiency of the engine.

Le moteur à allumage commandé fortement downsizé est une des solutions les plus prometteuses utilisée par les constructeurs automobiles pour augmenter le rendement et réduire les émissions de CO2. Cependant, les conditions thermodynamiques plus sévères rencontrées dans ces moteurs favorisent l’apparition de combustions anormales (cliquetis et rumble) qui sont difficiles à analyser expérimentalement vu les risques encourus par le moteur. La méthode Reynolds Averaged Navier-Stokes (RANS) s’est imposée depuis plusieurs années pour l’étude des moteurs à piston dans l’industrie, mais elle n’est pas la plus appropriée pour étudier des phénomènes locaux et sporadiques comme les combustions anormales qui n’affectent pas le cycle moyen simulé en RANS. Grâce à l’utilisation d’un code compressible LES et au développement d’une version améliorée des modèles ECFM-LES (Extended Coherent Flame Model) et TKI (Tabulated Kinetics of Ignition) qui permet un découplage total entre les taux de réaction liés à la propagation de la flamme et à l’auto-inflammation, ces travaux mettent en évidence pour la première fois la capacité de la LES à décrire le phénomène de cliquetis dans une configuration réaliste d’un moteur à allumage commandé. Contrairement aux études précédentes [S. Fontanesi and S. Paltrinieri and A. D’Adamo and G. Cantore and C. Rutland, SAE Int. J. Fuels Lubr., 2013-01-1082, pp. 98-118][G. Lecocq, S. Richard, J.-B. Michel, L. Vervisch, Proc. Combust. Inst. 33 (2011) 3105-3114], une étude quantitative du cliquetis est réalisée grâce à des post-traitements spécifiques et similaires pour les résultats expérimentaux et numériques. La LES est capable de prédire la variabilité de la pression cylindre, la fréquence mais également l’angle moyen d’apparition de l’auto-inflammation sur un balayage d’avance à l’allumage. Une analyse 3D démontre également que le cliquetis se déclenche à différents endroits, mais principalement dans la moitié de la chambre sous les soupapes d’échappement. De plus, l’intensité du cliquetis est proportionnelle à la masse de gaz frais brûlée en auto-inflammation pour les faibles intensités, alors qu’une croissance beaucoup plus forte est observée pour les intensités les plus élevées. Ceci suggère que des facteurs supplémentaires interviennent comme la localisation du cliquetis ou les interactions entre l’acoustique interne et l’auto-inflammation. L’utilisation d’un code LES compressible permet une visualisation directe de ces interactions mettant en évidence que les faibles intensités sont liées à des auto-inflammations locales sans couplage alors qu’une transition de la déflagration vers la détonation est possible en moteur automobile et correspond aux intensités les plus fortes. / Highly boosted spark ignition engines are more and more attractive for car manufacturers in terms of efficiency and CO2 emissions reduction. However, thermodynamic conditions encountered in these engines promote the occurrence of abnormal combustions like knock or super-knock, which are experimentally difficult to analyze due to the risks of engine damages. The Reynolds Averaged Navier-Stokes (RANS) method mainly used in industry for piston engines is not the most appropriate as knock does not always affect the mean cycle captured by RANS. Using an accurate LES compressible code and improved versions of ECFM-LES (Extended Coherent Flame Model) and TKI (Tabulated Kinetics of Ignition) models allowing a full uncoupling of flame propagation and auto-ignition reaction rates, this work demonstrates for the first time that LES is able to describe quantitatively knocking combustion in a realistic downsized SI engine configuration. Contrary to previous studies [S. Fontanesi and S. Paltrinieri and A. D’Adamo and G. Cantore and C. Rutland, SAE Int. J. Fuels Lubr., 2013-01-1082, pp. 98-118][G. Lecocq, S. Richard, J.-B. Michel, L. Vervisch, Proc. Combust. Inst. 33 (2011) 3105-3114], a quantified knock analysis is conducted based on a specific post-processing of both numerical and experimental data. LES is able to predict the in-cylinder pressure variability, the knock occurrence frequency and the mean knock onset crank angle for several spark timings. A 3D analysis also demonstrates that knock occurs at random locations, mainly at the exhaust valves side. Knock intensity is found proportional to the fresh gases mass burned by auto-ignition at low knock intensities, while an exponential increase at the highest intensities suggests the influence of additional factors like the knock location in the cylinder or complex behavior of knocking combustion. A direct LES study of acoustic and autoignition interactions is then achieved. The LES visualizations allows showing that low knock intensities are only linked to local autoignition, but a deflagration to detonation transition occurs in such engine operating conditions and is responsible for the highest knock intensities.

The subject of this diploma thesis is the creation of a spark ignition thermodynamics model using pressure data measured on the actual engine. The model made in Matlab programming language combines Wiebe function for fuel energy release and Woschni correlation for heat transfer between in-cylinder gasses and cylinder walls. The created model contains compression and expansion stroke only, that's why are conditions at the start of compression and total heat addition calculated by measured pressure data from Skoda 1.0 MPI engine. Creation of transparent model by Matlab scripts enables other users to understand the basics of „zero-dimensional“ thermodynamics models properly, which are used by number of commercial solvers such as GT-Power simulation software. First part of this thesis deals with fundamental laws of heat addition and heat transfer, description of equations for its modelling and application. The major section is devoted to Matlab model, where defined input parameters are mentioned, description of model operation and model parameters influence study. Next parts develops issues of combustion pressure measurement and creation of engine simulation by GT-Power software used for comparison with Matlab model. In the thesis conclusion are simulations and actual engine data differences discussed.

No description available.

This work concerns a systematic study of IC engine operation with 100% biogas as fuel (as opposed to the dual-fuel mode) with particular emphasis on operational issues and the quest for high efficiency strategies. As a first step, a commercially available 1.2 kW genset engine is modified for biogas operation. The conventional premixing of air and biogas is compared with a new manifold injection strategy. The effect of biogas composition on engine performance is also studied. Results from the genset engine study indicate a very low overall efficiency of the system. This is mainly due to the very low compression ratio (4.5) of the engine. To gain further insight into factors that contribute to this low efficiency, thermodynamic engine simulations are conducted. Reasonable agreement with experiments is obtained after incorporating estimated combustion durations. Subsequently, the model is used as a tool to predict effect of different parameters such as compression ratio, spark timing and combustion durations on engine performance and efficiency. Simulations show that significant improvement in performance can be obtained at high compression ratios. As a step towards developing a more efficient system and based on insight obtained from simulations, a high compression ratio (9.2) engine is selected. This engine is coupled to a 3 kW alternator and operated on 100% biogas. Both strategies, i.e., premixing and manifold injection are implemented. The results show very high overall (chemical to electrical) efficiencies with a maximum value of 22% at 1.4 kW with the manifold injection strategy. The new manifold injection strategy proposed here is found to be clearly superior to the conventional premixing method. The main reasons are the higher volumetric efficiency (25% higher than that for the premixing mode of supply) and overall lean operation of the engine across the entire load range. Predictions show excellent agreement with measurements, enabling the model to be used as a tool for further study. Simulations suggest that a higher compression ratio (up to 13) and appropriate spark advance can lead to higher engine power output and efficiency.

For an engine running at a constant speed, both exhaust and intake processes are periodic in nature. This inspires the muffler designer to go for the much easier and faster frequency domain modeling. But analogous to electrical filter, as per Thevenin’s theorem, the acoustic filter or muffler requires prior knowledge of the load-independent source characteristics (acoustic pressure and internal impedance), corresponding to the open circuit voltage and internal impedance of an electrical source. Studies have shown that it is not feasible to evaluate these source characteristics making use of either the direct measurement method or the indirect evaluation method. Hence, prediction of the radiated exhaust or intake noise has been subject to trial and error. Making use of the fact that pressure perturbation in a duct is a superposition of the forward moving wave and the reflected wave, a simple hybrid approach has been proposed making use of an interrelationship between progressive wave variables of the linear acoustic theory and Riemann variables of the method of characteristics. Neglecting the effect of nonlinearities, reflection of the forward moving wave has been duly incorporated at the exhaust valve. The reflection co-efficient of the system downstream of the exhaust valve has been calculated by means of the transfer matrix method at each of the several harmonics of the engine firing frequency. This simplified approach can predict exhaust noise with or without muffler for a naturally aspirated, single cylinder engine. However, this proves to be inadequate in predicting the exhaust noise of multi-cylinder engines. Thus, estimation of radiated noise has met only limited success in this approach. Strictly speaking, unique source characteristics do not exist for an IC engine because of the associated non-linearity of the time-varying source. Yet, a designer would like to know the un-muffled noise level in order to assess the required insertion loss of a suitable muffler. As far as the analysis and design of a muffler is concerned, the linear frequency-domain analysis by means of the transfer matrix approach is most convenient and time saving. Therefore, from a practical point of view, it is very desirable to be able to evaluate source characteristics, even if grossly approximate. If somehow it were possible to parameterize the source characteristics of an engine in terms of basic engine parameters, then it would be possible to evaluate the un-muffled noise before a design is taken up as a first approximation. This aspect has been investigated in detail in this work. A finite-volume CFD (one dimensional) model has been used in conjunction with the two-load or multi-load method to evaluate the source characteristics at a point just downstream of the exhaust manifold for the exhaust system, and upstream of the air filter (dirty side) in the case of the intake system. These source characteristics have been extracted from the pressure time history calculated at that point using the electro-acoustic analogy. Systematic parametric studies have yielded approximate empirical expressions for the source characteristics of an engine in terms of the basic engine parameters like engine RPM, capacity (swept volume or displacement), air-fuel ratio, and the number of cylinders. The effect of other parameters has been found to be relatively insignificant. Unlike exhaust noise, the intake system noise of an automobile cannot be measured because of the proximity of the engine at the point of measurement. Besides, the intake side is associated with turbocharger (booster), intercooler, cooling fan, etc., which will make the measurement of the intake noise erroneous. From the noise radiation point of view, intake noise used to be considered to be a minor source of noise as compared to the exhaust noise. Therefore, very little has been done or reported on prediction of the intake noise as compared to the exhaust noise. But nowadays, with efficient exhaust mufflers, the un-muffled intake noise has become a contributing factor to the passenger compartment noise level as a luxury decisive factor. Therefore, in this investigation both the intake and the exhaust side source characteristics have been found out for the compression ignition as well as the spark ignition engines. Besides, in the case of compression ignition engines, typical turbocharged as well as naturally aspirated engines have been considered. One of the inputs to the time-domain simulation is the intake valve and exhaust valve lift histories as functions of crank angle. It is very cumbersome and time-consuming to measure and feed these data into the program. Sometimes, this data is not available or cannot be determined easily. So, a generalized formula for the valve lift has been developed by observing the valve lift curves of various engines. The maximum exhaust valve lift has been expressed as a function of the swept volume of the cylinder. This formulation is not intended for designing a cam profile; it is for the purpose of determining approximate thermodynamic quantities to help a muffler designer for an initial estimation. It has also been observed during the investigation that from the acoustic point of view, sometimes it is better to open the exhaust valve a little earlier, but very slowly and smoothly, and keep it open for a longer time. Although the exact source characteristics for an automobile engine cannot be determined precisely, yet the values of source characteristics calculated using this methodology have been shown to be reasonably good for approximate prediction of the un-muffled noise as well as insertion loss of a given muffler. The resultant empirical expressions for the source characteristics enable the potential user to make use of the frequency-domain cum-transfer matrix approach throughout; the time consuming time-domain simulation of the engine exhaust source is no longer necessary. Predictions of the un-muffled sound pressure level of automotive engines have been corroborated against measured values as the well as the full scale time-domain predictions making use of a finite-volume software.

The diploma thesis is focused on analysis of noise level of mobile power vehicles in relation to motor operation mode and its evaluation. The thesis core lies within measurement of acoustic pressure levels at four vehicles in different motor operation modes by two audio-noise meters. One meter was places within the cabin, the other outside. The results of the work showed a development in reducing noise at modern power vehicles.

The present work studies the use of a two-zone computer model to simulate the operation of an internal combustion engine with spark ignition fueled with alcohol fuels and gasohol. To fit the model to the experimental data, a parameter estimation technique was used and the heat transfer correlation that could better fit the tested fuels and engine was determined. The tested fuels were: hydrous ethanol, wet ethanol (from 10% to 40% of water, by volume), n-butanol, n-butanol/ethanol blend and gasohol. In addition to the experimental tests with the engine, tests with a packed distillation column under batch process were made in order to determine the energy efficiency involved between production and use as a fuel for hydrous ethanol and wet ethanol fuels. The results showed that the two-zone model was able to predict satisfactorily the behavior of all tested fuels, accurately obtaining the engine performance parameters. In terms of energy efficiency, wet ethanol fuels have advantage over hydrous ethanol fuel, especially in the case of 30% of water by volume, where energy efficiency reaches its maximum value, considering the distillation and engine combustion processes. The n-butanol fuel was capable of act as a surrogate for both hydrous ethanol and gasohol with efficiency, leading the engine to have good performance in the tested operational conditions and appearing, due to this, as an interesting alternative of renewable fuel to be inserted in the Brazilian energy matrix. / O presente trabalho investiga o uso de um modelo computacional de duas zonas para simular o funcionamento de um motor de combustão interna com ignição por centelha abastecido com álcoois combustíveis e gasolina. Para o ajuste do modelo fez-se uso de técnica de estimação de parâmetros e determinação da correlação de transferência de calor capaz de melhor se ajustar aos combustíveis e ao motor testados. Os combustíveis utilizados foram: etanol hidratado, etanol super-hidratado (de 10% a 40% de água, em volume), n-butanol, misturas de n-butanol e etanol e gasolina e etanol. Além dos testes experimentais com motor, testes de bancada com uma coluna de destilação recheada em regime descontínuo foram realizados a fim de determinar a eficiência energética do processo de produção e queima de etanol hidratado e super-hidratado. Os resultados obtidos mostraram que o modelo de duas zonas é capaz de prever de maneira satisfatória o comportamento de todos os combustíveis testados, com determinação precisa de parâmetros de desempenho do motor. Em termos de eficiência energética, o etanol super-hidratado tem vantagem em relação ao etanol hidratado combustível, em especial quando com 30% de água em volume, onde a eficiência energética é máxima, considerados os processos de destilação e queima no motor. O n-butanol combustível usado mostrou-se capaz de substituir eficientemente tanto o etanol hidratado como a gasolina brasileira, levando o motor a ter boa performance nas condições operacionais testadas e aparecendo, dessa forma, como interessante alternativa de combustível renovável a ser inserida na matriz energética brasileira.

Depuis quelques années, les modèles 0D trouvent un regain d'intérêt auprès des motoristes. En effet, ces modèles, fournissant aisément un comportement thermodynamique du moteur, peuvent être couplés avec des outils de contrôle moteur. Néanmoins, leur précision doit être augmentée, pour répondre aux enjeux technologiques actuels. Dans les moteurs à allumage commandé, la flamme turbulente prémélangée est modélisée comme un ensemble de flammelettes cohérentes entre elles. Cette approche généraliste nécessite un traitement particulier en proche paroi, motivé par une modification de la structure de flamme due aux couches limites thermique et cinématique. Ce présent travail propose des approches de modélisations 0D de la combustion, en proche paroi et dans la zone réactionnelle de la flamme. Pour modéliser la combustion en proche paroi, la flamme est scindée en une contribution en propagation libre, et une contribution en interaction avec les parois. Chaque contribution est divisée en une zone de transport, dans laquelle l'entraînement des gaz frais est décrit, et une zone de réaction, dans laquelle la réaction de combustion est modélisée. L'ajout d'une zone de réaction en interaction avec les parois permet de modéliser un gradient de température et une réaction de combustion ralentie en proche paroi. Pour modéliser la zone réactionnelle, une discrétisation de la flamme en N zones de réaction indépendantes est proposée. Une plage de fonctionnement moteur a été simulée avec nos approches de modélisation, afin de quantifier la variabilité des paramètres de calibration. Pour ce faire, les modèles sont calibrés sur chaque point de fonctionnement, par une méthode de minimisation de l'erreur quadratique moyenne sur la loi de dégagement d'énergie. Des corrélations aisées de paramètres de calibration peuvent être établies, en fonction de paramètres moteurs. Les résultats de simulations, obtenus à partir de ces corrélations, sont satisfaisants. / Recently, the interest for zero-dimensional models has increased. Indeed, these models provide easily the engines thermodynamic behavior and can be coupled with control tools. However, their accuracy must be improved to meet the current technological challenges. In the spark ignition engines, the premixed turbulent flame is modeled as a set of coherent flamelets. This approach requires special treatment near the walls, motivated by the modifications of the flame structure due to boundary layers. The present work proposes 0D modeling of combustion near the walls and in the reaction zone of the flame. To combustion model near the walls, the flame is divided into a free propagation contribution, and an interacting contribution with the walls. Each contribution is divided into a convective zone, wherein the entrainment of fresh gas is described, and a reaction zone, wherein the combustion reaction is modeled. Adding a reaction zone near the walls allows modeling a thermal gradient and a slower combustion reaction near the walls. To model the reaction zone, a flame discretization is made into several reaction zones. An engine operating range is simulated with our models, for quantifying the calibration parameters variability. To do this, models are calibrated on each operating point, by a method of minimization of the quadratic error on the heat released rate. Linear correlations can be found, depending on engines parameters. A good agreement between experimental data and simulation results is obtained with these parameters correlations.