This report has been carried out together with Bonava with the purpose to investigate the difference in climate impact and cost of both concrete and wooden frames in apartment buildings. This to investigate if it is profitable to build climate smart. To perform this, a life cycle analysis and a life cycle cost analysis were performed on two frames of different materials; a wooden frame called "Nästet 3" and a concrete frame called "Kv. Smugglaren”. The results of the life cycle analysis shows that the wooden frame “Nästet 3” has less climate impact in comparison to the concrete frame “Kv. Smugglaren”. The wooden frame had a total emission of 176 tons of CO2e which is about 65 kg CO2e per square meter of gross area. The result of the life cycle analysis on the concrete frame “Kv. Smugglaren” showed a climate impact of 793 tons of CO2e, which approximately is 229 kg CO2e per square meter of gross area. This study shows that a concrete frame in apartment buildings has a greater climate impact than a wooden frame. The results of the life cycle cost analysis shows that the wooden frame “Nästet 3” has the lowest frame material cost, about half as much as the concrete frame “Kv. Smugglaren”. However, it has the largest total construction cost, approximately 0.8% larger than the concrete frame. When all results are compared, it can be concluded that it does not necessarily cost more to build with more climate-smart materials. Using wood as a frame material is both more climate-smart and cheaper than concrete.

The goal for this project was to analyze and understand the noise of the ion beam analysis technique, Elastic Recoil Detection Analysis (ERDA). This was done by examining two models: Classical models and a prediction model. The prediction model is a parameterized noise distribution model. After examining the models, we concluded that both models had advantages and disadvantages for ERDA analysis. This information could be applicable to our understanding of how ERDA could improve for our analysis of wall materials, which could lead to the overall development of fusion reactors. / Målet för detta projekt var att analysera och förstå brus från jonstråleanalystekniken, Elastic Recoil Detection Analysis (ERDA). Detta gjordes genom att granska två modeller: Klassiska brusreduceringsmodeller och en förutsägelsemodell. Förutsägelsemodellen är en parametrerad brusfördelningsmodell. Efter granskningen av modellerna drog vi slutsatsen att båda modellerna hade fördelar och nackdelar för ERDA-analys. Denna information kan vara tillämplig på vår förståelse av hur ERDA kan förbättras för vår analys av väggmaterial, vilket kan leda till den övergripande utvecklingen av fusionsreaktorer. / Kandidatexjobb i elektroteknik 2021, KTH, Stockholm

The most used design approach for civil engineering structures is a trial and error procedure; the designer chooses an initial configuration, tests it and changes it until all safety requirements are met with good material utilization. Such a procedure is time consuming and eventually leads to a feasible solution, while several better ones could be found. Indeed, together with safety, environmental impact and investment cost should be decisive factors for the selection of structural solutions. Thus, structural optimization with respect to environmental impact and cost has been the subject of many researches in the last decades. However, design techniques based on optimization haven’t replaced the traditional design procedure yet. One of the reasons might be the constructive feasibility of the optimal solution. Moreover, concerning reinforced concrete beam bridges, to the best of the author knowledge, no study in the literature has been published dealing with the optimization of the entire bridge including both the structural configuration and cross-section dimensions. In this thesis, a two-steps automatic design and optimization procedure for reinforced concrete road beam bridges is presented. The optimization procedure finds the solution that minimizes the investment cost and the environmental impact of the bridge, while fulfilling all requirements of Eurocodes. In the first step, given the soil morphology and the two points to connect, it selects the optimal number of spans, type of piers-deck connections and piers location taking into account any obstacle the bridge has to cross. In the second and final step, it finds the optimal dimensions of the deck cross-section and produces the detailed reinforcement design. Constructability is considered and quantified within the investment cost to avoid a merely theoretical optimization. The wellknown Genetic Algorithm (GA) and Pattern Search optimization algorithms have been used. However, to reduce the computational effort and make the procedure more user-friendly, a memory system has been integrated and a modified version of GA has been developed. Moreover, the design and optimization procedure is used to study the relationship between the optimal solutions concerning investment cost and environmental impact. One case study concerning the re-design of an existing road bridge is presented. Potential savings obtained using the proposed method instead of the classic design procedure are presented. Finally, parametric studies on the total bridge length have been carried out and guidelines for designers have been produced regarding the optimal number of spans. / <p>QC 20190304</p>

<p>Generation of narrow segments is a matter of concern in step-and-shoot intensity modulated radiotherapy for several reasons. The measurement, calculation and delivery of dose from narrow segments may be complicated due to: the dosimetric properties of the detector; the effect of beam penumbra and heterogeneities within the patient; and the requirement for high geometric delivery precision respectively. The main purpose of this thesis was to investigate the parameters affecting the generation of narrow beam segments in IMRT optimization. Parameters such as effective source size, Gaussian height and width, density of the target volume, and gap between the tumor and normal tissue were varied to determine their influence on the number of narrow leaf pair separations. The gradient and penumbra were also examined. Two simple geometric models (thick model and thin model) with different dimensions were used. In the thick model, two 6-MV photon beams were incident on the target at right angles. A rectangular target was centered in a phantom with dimensions 20.25 cm×5.25 cm×20.25 cm. In the thin model, one 6-MV photon beam was normally incident on a 20.25 cm×1.25 cm×20.25 cm slab phantom. The relationship between the penumbra and number of narrow separated leaf pairs were examined for the thick model. The results did not show a consistent pattern. For the thin model, creating a gap between the target and the OAR decreased the total number of narrowly separated leaf pairs along the interface but increased the average dose delivered to the OAR. By varying the OAR max dose or the gap between the target and OAR, a peak was created in the dose profiles to compensate the penumbra. As gradient increased the peak height increased to compensate the dose fall-off. The width of the peak at half maximum changed with gradient but not in a predictable fashion.</p> / Master of Science (MSc)

<p>InP nanowires with short InAs segments were grown on InP (111)B substrates by Au assisted vapour-liquid-solid growth in a gas source molecular beam epitaxy system. Nanowire crystal structure and morphology were investigated by transmission electron microscopy as a function of temperature, growth rate, and V/III flux ratio. At 370C predominantly kinked nanowires with random morphology and low areal density were observed with a rough parasitic 2D film. At 440C, nanowire density was also reduced but the 2D film growth was smoother and nanowires grew straight without kinking. An optimum temperature of 400C maximized areal density with uniform nanowire morphology. At the optimum temperature of 400C, an increase in V/III flux ratio changed the nanowire morphology from rod-shaped to pencil like indicating increased radial growth. Growth rate did not affect the crystal structure of InP nanowires. For InAs nanowires, changing the growth rate from 1 to 0.5 μm/hr reduced the presence of stacking faults to as low as one per nanowire. Short InAs segments in InP nanowires were found to grow through two mechanisms for nanowires of length L and diameter D. The first mechanism described the supply of In to the growth front via purging of In from the Au droplet where L was proportional to D. The second mechanism involved direct deposition of adatoms on the nanowire sidewall and subsequent diffusion to the growth front where L was proportional to 1/D. For intermediate growth durations, a transition between these two mechanisms was observed. For InP and InAs nanowires, the growth mode was varied from axial to radial through the inclusion of Al to form a core shell structure. Al_xIn_1-xAs(P) shells were grown on InAs cores with Al alloy fractions between 0.53 and 0.2. These nanowires were examined by transmission electron microscopy and it was found, for all values of x in InAs-Al_xIn_1-xP structures, that relaxation had occurred through the introduction of dislocations. For InAs-Al_xIn_1-xAs structures, all values except x=0.2 had relaxed through dislocation formation. A critical thickness model was developed to determine the core-shell coherency limits which confirmed the experimental observation of strain relaxation. The effects of passivation on the electronic transport and the optical properties were examined as a function of structural core-shell passivation and chemical passivation. The mechanisms for the observed improvement in mobility for core-shell versus bare InAs nanowires was due to the reduction in ionized impurity scattering from surface states. Similarly an increase in photoluminescence intensity after ammonium sulfide passivation was explained by the reduction of donor type surface states.</p> / Doctor of Philosophy (PhD)

<p>This study examined the self-trapping of light emitted by a miniature green laser in a photopolymerizable medium and the interactions between two parallel-propagating self-trapped beams. The work included the design and fabrication of an Intra-Cavity Frequency-Doubling (IC-FD) Nd: YVO₄/MgO: PPLN miniature green laser with a stable and tunable output intensity. Emission from this laser enabled a systematic examination of self-trapping phenomena at incident intensities spanning 8 orders of magnitude (3.2× W·cm^-2to 6368 W·cm^-2). When launched into a photopolymerizable medium, light emitted by the miniature green laser self-trapped by initiating polymerization and corresponding changes in refractive index along its propagation path. The evolution and dynamics of the self-trapped beam corresponded to the behaviour of self-trapped beams of coherent light. Interactions between a pair of parallel-propagating self-trapped beams were also characterised at a range of intensities. This study shows that the miniature green laser is an efficient, coherent source with a large range of output intensities for the excitation of self-trapped beams. This opens opportunities for its incorporation into small-scale optical systems designed to operate based on the generation and interactions of self-trapped beams.</p> / Master of Applied Science (MASc)

Three dimensional imaging in the form of Cone Beam Computed Tomography has become prevalent in the field of orthodontics. Analytical methods of resulting volumetric data sets have not kept pace with the technology capable of producing them. Current 3D analysis techniques are largely adaptations of existing 2D methods, offering no clear diagnostic advantage over traditional imaging techniques in light of increased radiation exposure, and cannot be compared with norms generated from 2D image capture sources. In order to study morphology in 3D, data sets must be generated for longitudinal studies and native 3D analytical methods must also be developed. Existing methods of CBCT volume superimposition are cumbersome, involving complex software pipelines and multiple systems to complete the process. The goal of the current study was to develop a reproducible method of CBCT volume superimposition in the posterior cranial base in a single software package, and construct an easy to follow, step-by-step manual to facilitate future studies in craniofacial morphology. Existing anonymized sequential CBCT volumes of three subjects meeting inclusion criteria were obtained from the Kornberg School of Dentistry Department of Radiology. Volumes for each subject were imported into AMIRA software, resampled to a standardized 0.5 mm voxel size and superimposed with a mutual information algorithm. Posterior cranial base surface data was extracted using a semi-automatic technique. Resulting surface distance data was compiled and visualized through application of color maps. A streamlined image processing protocol was produced and documented in a detailed step-by-step manual. Surface distance analysis of serial segmentations was performed to verify reliability of the process. Surface distance deviations greater than 0.5 mm consistently fell below 0.2 percent of the total surface area. Sequential scan superimpositions of all three subjects exhibited mean surface distances of less than 0.15 mm. Two out of three subjects exhibited deviations of greater than 0.5 mm in less than 1 percent of the total surface area, suggesting consistent sub-voxel accuracy of the protocol. / Oral Biology

Advancements in nanoscale engineering of oxide interfaces and heterostructures have led to discoveries of emergent phenomena and new artificial materials. Reactive molecular-beam epitaxy (MBE) and pulsed-laser deposition (PLD) are the two most successful growth techniques for epitaxial heterostructures of complex oxides. PLD possesses experimental simplicity, low cost, and versatility in the materials to be deposited. Reactive MBE employing alternately-shuttered elemental sources (atomic layer-by-layer MBE, or ALL-MBE) can control the cation stoichiometry precisely, thus producing oxide thin films of exceptional quality. There are, however, major drawbacks to the two techniques. Reactive MBE is limited to source elements whose vapor pressure is sufficiently high; this eliminates a large fraction of 4- and 5-d metals. In addition, the need for ozone to maintain low-pressure MBE conditions increases system complexity in comparison to conventional PLD. On the other hand, conventional PLD using a compound target often results in cation off-stoichiometry in the films. This thesis presents an approach that combines the strengths of reactive MBE and PLD: atomic layer-by-layer laser MBE (ALL-Laser MBE) using separate oxide targets. Ablating alternately the targets of constituent oxides, for example SrO and TiO2, a SrTiO3 film can be grown one atomic layer at a time. Stoichiometry for both the cations and oxygen in the oxide films can be controlled. Using Sr1+xTi1-xO3, CaMnO3, BaTiO3 and Ruddlesden–Popper phase Lan+1NinO3n+1 (n = 4) as examples, the technique is demonstrated to be effective in producing oxide films with stoichiometric and crystalline perfection. By growing LaAl1+yO3 films of different stoichiometry on TiO2-terminated SrTiO3 substrate at high oxygen pressure, it is shown that the behavior of the two-dimensional electron gas at the LaAlO3/SrTiO3 interface can be quantitatively explained by the polar catastrophe mechanism. / Physics

Nuclear physics tells us a lot about astrophysics, particularly the energy generation in stars. The present work is a thesis in experimental nuclear physics, reporting the results of 30S radioactive beam development for a future experiment directly measuring data to extrapolate the 30S(α,p) stellar reaction rate in Type I X-ray bursts, a phenomena where nuclear explosions occur repeatedly on the surface of accreting neutron stars. On the astrophysics side, the work details basic stellar physics and stellar reaction formalism in Chapter 1, the behaviour of compact stars in Chapter 2, and a full literature review of Type I X-ray bursts in Chapter 3. Nuclear experiments are non-trivial, and the results reported here were not accomplished by the author alone. Stable-beam experiments are technically challenging and involved, but for the case at hand, the halflife of 30S is a mere 1.178 seconds, and in order to measure reaction cross-sections, we must make a beam of the radionuclide 30S in situ and use these rare nuclei immediately in our measurement. Particle accelerator technology and radioactive ion production are treated in Chapter 4, and the experimental facility and nuclear measurement techniques are discussed in some detail in Chapter 5. In order to perform a successful future experiment which allows us to calculate the stellar 30S(α, p) reaction rate, calculations indicate we require a 30S beam of ~ 10^5 particles per second at ~ 32 MeV. Based on our recent beam development experiments in 2006 and 2008, it is believed that such a beam may be fabricated in 2009 according to the results presented in Chapters 6 and 7. We plan to measure the 4He(30S,p) cross-section at astrophysical energies in 2009, and some remarks on the planned (α,p) technique are also elucidated in Chapters 5, 6 and 7. / Thesis / Master of Science (MSc)

Human bone tissue has an inherent hierarchical structure, which is integral to its material properties. It is primarily composed of a collagen fiber matrix that is mineralized with hydroxyapatite. A comprehensive understanding of bone and the linkages between structural and cellular organization is imperative to developing fundamental knowledge that can be applied to better our understanding of bone disease manifestations and its interaction with implant devices. Herein, this thesis investigated non-traditional methods for evaluating bone structure across the nano- and meso-length scales. Firstly, due to the inhomogeneous organization of collagen fibrils and mineral platelets of bone ultrastructure, a suitable methodology for the investigation of both phases needed to be generated. In this work, focused ion beam (FIB) microscopy was employed to create site-specific scanning transmission electron microscopy (STEM) lift-outs of human osteonal bone that could be visualized with correlatively with STEM and small angle X-ray scattering (SAXS). Samples were successfully characterized using both techniques, and minimal visual damage was induced during data acquisition. This work is the first to demonstrate the potential for bone to be investigated correlatively using both STEM and SAXS. Secondly, this work is the first to employ a dual-beam plasma FIB (PFIB) equipped with a scanning electron microscope (SEM), to investigate bone tissue across the mesoscale. This equipment enables large volume three-dimensional (3D) imaging at nanoscale resolution across larger mesoscale volumes. This thesis aimed to reduce ion beam-based artifacts, which presents as curtain-like features by adjusting the composition of protective capping layers. Subsequently, large volume tomograms of bone tissue were acquired, demonstrating the effectiveness of the PFIB to reveal mesoscale features including the cellular network of bone tissue. Overall, this thesis has developed methods that allow for the application of advanced microscopy techniques to enhance the understanding of bone tissue across the nanoscale and mesoscale. / Thesis / Master of Applied Science (MASc) / Bone tissue has a unique structure that perplexes both biologists and materials scientists. The hierarchical structure of bone has garnered the interest of materials scientists since the body’s skeletal strength and toughness are governed by the nanoscale (millionth of centimetres) to macroscale (centimeters) organization of bone. In this work, the intricate organization of bone is investigated using advanced electron and ion beam microscopy techniques, which achieve high-resolution imaging of bone structure. Firstly, this work developed a sample preparation workflow to correlate electron and X-ray imaging of the same bone tissue. Secondly, this work was the first to apply serial-sectioning plasma focused ion beam tomography to human bone tissue to investigate its structure at high resolution across micron-sized volumes. Here, previously unexplored methodologies to image bone are demonstrated with the hopes of applying such techniques to investigate healthy and pathological bone tissue in the future.