Sorption of quaternary metal ions (Pb2+, Cu2+, Cd2+ and Zn2+) was carried out on lignite from the South Moravia. Following experiments were tested: kinetic sorption, dependence of sorption on pH, initial concentration, temperature, effect of electrolytes (KNO3 and NaCl) and desorption in deionized water. Sorption studies was carried out in quaternary mixtures and in the case of inicial concentration effect additional in a single-component solution. The batch sorption experiments was used. Sorption time was 24 hour, although concentration of ions was a near equilibrium after two hour. As the optimal pH was determined pH 5. The order of affinity by lignite was obtained Pb >> Cd > Zn > Cu for the sorption of metals in the single-component solution and the order was Pb > Cu > Zn > Cd for the sorption of mixture of metals. The maximum adsorptium capacities from single solutions were for Pb 97,82 mg/g, Cd 60,34 mg/g, Zn 49,88 mg/g and Cu 30,28 mg/g and in the case of ones from mixture solutions were for Pb 39,03 mg/g, Cu 25,94 mg/g, Zn 15,21 mg/g and Cd 5,18 mg/g. Experimental data have been analysed using Langmuir and Freundlich model. Thermodynamic values H°, S° and G° were calculated. Desorption test showed that desorption efficiency is 0–3 %. NaCl had the greatest influence on sorption from electrolytes. On the basis obtained results we can say that metals are binding to lignite in particular due to chemical interactions. Lignite is s suitable as a sorption material for metal ions especially in the field of low concentrations.

This thesis was focused on the possibility of secondary utilization of waste material from the wine industry to remove heavy metals from wastewater. In the theoretical part, there were discussed mainly the problems of heavy metals pollution including methods of their removal and ICP-OES detection. Furthermore, the waste material from the wine production and the possibilities of its further processing were discussed there. The primary objective of the experimental part was to characterize the material by IR analysis, optimization of adsorption conditions, isotherms construction and determination of maximum adsorption capacities of white, red and chemically modified marc for Cd, Cr, Cu, Ni and Pb. From the parameters influencing the adsorption efficiency, the adsorbent load was optimized (m/V ratio = 0,02); pH values found were 5 for Cd, Cu, Ni, Pb and 3 for Cr and the contact time to reach the equilibrium was 15 minutes for Cd, Ni, Pb and 30 minutes for Cr and Cu. Maximum adsorption capacity for heavy metals were calculated from adsorption isotherms by applying the Langmuir model and found to be 18,829 7 mg/g for Cd; 10,664 7 mg/g for Ni; 35,602 0 mg/g for Pb (modified marc with 1M NaOH); 4,678 4 mg/g for Cu and 9,629 0 mg/g for Cr. The results of the work confirm the good adsorption potential of heavy metals on marc and the positive effect of chemical modification of natural biosorbents to improve their adsorption capacity.

This thesis deals with optimalization processes of adsorption of ferulic acid on different types of sorbents. Specifically, was used the activated carbon as a sorbent of heterogeneous character and Amberlyst A-21 and Amberlit XAD-16 as macroporous polymer sorbents. The ferulic acid is fully characterized in the theoretical part and are discussed the problems of adsorption processes. To determination of the phenolic acid were used UV-VIS and HPLC instrumental methods. The main aim of the experimental part is to optimize various parameters of adsorption, including the construction of adsorption isotherms, determination of maximum adsorption capacity of individual sorbents, study of kinetics and mechanisms of adsorption. Determination of the influence of salt was studied to assess the impact of the inorganic salts on the ferulic acid adsorption capacity. Based on these parameters, was carried out determination of an optimal pH value on 3, with an optimal adsorbent load (m/V ratio = 0,009 gml-1) and a contact time of 50 min for all three adsorbents. Equilibrium studies described by adsorption isotherms and the Langmiur model fitted the best, and the maximum adsorption capacities were determined for all three sorbents with 150,4 mgg-1 for activated carbon, 209,1 mgg-1 for Amberlyst A-21 and 82 mgg-1 for Amberlyte XAD-16. In the study of kinetic models was selected pseudo-second model for all three adsorbents, which correlated with the results obtained by the Langmuir isotherm. The decrease in adsorption capacity in the determination of NaCl influence was 4 % for activated carbon, for macroporous polymer sorbents was decreased by 52 % and 55 % for Amberlyst A-21 and Amberlyt XAD-16 respectively. In a selectivity test under optimized conditions, adsorption strength increased in the order of sinapic acid ferulic acid p-coumaric acid for polymeric sorbent XAD-16 and activated carbon. For the A-21 sorbent the adsorption strength increased in the order of p-coumaric acid ferulic acid sinapic acid. The results of the work indicate the suitability of all three sorbents for the phenolic acid adsorption.

The Diploma thesis deals with humic acids and their ability to adsorb metal ions on their surface. Humic acids are aromatic polycyclic compounds which contain carboxylic and fenolic functional groups on their sidechains. Thanks to these functional groups humic acids can form complexes with metal ions of different stability and assist the partial immobilization of pollutants in the nature. In this thesis, the sorption of Pb2+ and Zn2+ ions on humic acids was studied by relatively new electroanalytic method called galvanostatic stripping chronopotentiometry. Experimental data were described by Freundlich and Langmuir isotherms. The results show that the amount of examined metal ions increases with their increasing concentration. Furthermore it was determined that Pb2+ ions are adsorbed better on humic acids than Zn2+ ions. Both metals are adsorbed better from solution containing only one metal ion than in presence of four metals at the same time (Cd, Cu, Zn and Pb) where the sorption of these metals is not influenced by the presence of other metals.

Increasing demands for low heat losses and energy intensity of a building influence energy calculations. Higher demands are placed on the accuracy of the calculations. An important part of the thermal engineering calculations is the determination of the correct boundary conditions. An important input factor is primarily the indoor and outdoor environment, and temperature is the most important parameter for these types of enviromnent. It is not always the temperature of the external environment, but the environment that is adjacent to the soil or to unheated or differently heated spaces. The possibilities of modeling temperatures below the object are described in the standard ČSN EN ISO 10211. This standard specifies details for a geometric model for the numerical calculation of heat flows to assess the total heat loss of buildings or parts thereof, as well as to derive linear and point heat transfer factors. Furthermore, to calculate minimum surface temperatures to assess the risk of surface condensation and to determine the surface temperature factors. These are two different computational models. Therefore, it would be appropriate to simplify these calculations by simplifying the boundary conditions, namely to conduct an isotherm at a certain level below the terrain, which will be considered as a boundary condition, which is also based on long-term experience with "frost-free" depth. This calculation would be unambiguous, clear and simple.

4 ABSTRACT The synthesis has been described yielding a new type of rigid conjugated polymer networks which possess a high content of permanent micropores and macropores and exhibit high surface areas up to 1469 m2/g. The networks have been prepared via chain-growth coordination polymerization catalysed with insertion catalysts based on Rh complexes. This polymerization has been newly applied to bifunctional acetylenic monomers of diethynylarene type (1,4-diethynylbenzene, 1,3-diethynylbenzene and 4,4'-diethynylbiphenyl). The covalent structure of the networks consists of the polyacetylene main chains densely connected by arylene struts. The W and Mo metathesis catalysts have been revealed as inefficient for the synthesis of these networks. The increase in the polymerization temperature and time has been shown to affect positively the content and the diameter (up to 22 nm) of the mesopores in the networks. A mechanism has been proposed that explains the mesopores formation as a result of mutual knitting of small particles of the microporous polymer. The application of emulsion polymerization technique allowed to prepare texturally hierarchical polyacetylene networks possessing interconnected open macropores (diameter up to 4,8 μm) the walls of which exhibited micro/mesoporous texture. It was demonstrated...