The diploma thesis addresses the design and experimental verification of cooling system and low temperature part of UHV - STM working in temperature range of 20K - 300K. Due to the demand of variable temperature, the flow cooling system with cryogenic (~5 K) helium (He) is used. Two variants of the low temperature part of the microscope are studied. First the version with cooling only the sample holder, and second with cooling of the whole STM. Designed cooling system consists of He flow cryostat allowing to connect it to the Dewar vessel with liquid helium (LHe) using a low-loss transfer line. The cryostat consists of He inlet and outlet, heat exchangers and copper strains (i.e. braids) for the thermal connection of the sample holder/STM and radiation shield around the STM with the heat exchangers. The thesis describes the design of the flow cryostat and its initial tests in the designed vacuum chamber. Heat flow through a spot contact is also discussed to estimate thermal conductance of insulation supports based on thermal resistance of spherical contacts. The thesis was elaborated in collaboration with the Institute of Scientific Instruments of the ASCR, v.v.i.

This doctoral thesis is focused on the analysis of transport characteristics of submicron and micron transistors MOSFET. The assumption is a constant gradient of concentration, which leads to the fact that the diffusion current density is independent of the distance from the source. Active energy was determined from temperature dependence. The proposed physical model made it possible to determine the value of access resistance between drain and source their temperature dependence. Based on the assumption that the divergence of the gradient of the current density in the channel is zero. IV characteristics of the transistor MOSFET are derived and conducted experimental monitoring current channel depending on the collector voltage for the series of samples with different channel lengths in a wide temperature range from 10 to 350 K. Information on the concentration of charge transport in the channel and the position of the Fermi level at the point of active trap, which is the source of RTS noise, is obtained from the analysis of the transport characteristics. Determining the concentration of charge transport and the position of the Fermi level is important because these variables determine the intensity of quantum transitions and their values are not the same throughout the length of the channel. It was experimentally proved from the analysis of the characteristics of RTS noise that concentration at the local channel decreases with increasing current at a constant voltage on the gate and a variable voltage at the collector. Further, the position of active traps of RTS noise was intended and it was found that this is located near the collector. Active trap is located at the point where the Fermi level coincides with energy level of the traps.

V disertační práci je popsán heliový kryostat s experimentální válcovou konvekční celou pro studium proudění při přirozené konvekci za velmi vysokých Rayleigho čísel Ra (až do řádu 10^15) a Nusseltových čísel Nu (až do řádu 10^4). Pracovní látkou je studené 4He, které umožňuje díky výhodným fyzikálním vlastnostem dosažení velmi vysokých hodnot čísel Ra. Návrh kryostatu je založen na koncepci lázňových NMR kryostatů s nízkým odparem kryokapalin. Ve středu kryostatu je umístěna konvekční cela o průměru 300 mm a výšce 300 mm. Celu tvoří horní a spodní dno a výměnná střední část. Tyto díly jsou spojeny rozebíratelnými přírubami těsněnými indiovým drátem. Výměnná část umožňuje snadnou modifikaci geometrie cely. Hlavní přednost kryostatu spočívá v minimálním vlivu konstrukce cely a použitých materiálů na studovanou konvekci. Cela kryostatu je navržena pro pracovní tlaky do 250 kPa.

At the Forschungszentrum Rossendorf the build-up of the superconducting 1.3 GHz accelerator ELBE is still in progress. Furthermore a new sc photo injector (SRF gun) is under development, which should accelerate electrons up to 10 MeV at 1.3 GHz frequency. The use of electron accelerators is also more and more interesting for applications where the destructive potential of the electrons are used like sterilization of medical waste and medical products, food irradiation or decontamination of sewage. For these processes a high power is required to achieve a high product throughput in a plant. The aim is therefore to use beam powers of around 100 kW or more. Since the applications of electron accelerators in industrial environments are steadily increasing one can speculate about transferring the above named state of the arte technology to industrial electron accelerators. At the FZR a feasibility study of such a table top electron accelerator (TTE) has been performed to investigate its technical limits and marketabilitys.

At the Forschungszentrum Rossendorf the build-up of the superconducting 1.3 GHz accelerator ELBE is still in progress. Furthermore a new sc photo injector (SRF gun) is under development, which should accelerate electrons up to 10 MeV at 1.3 GHz frequency. The use of electron accelerators is also more and more interesting for applications where the destructive potential of the electrons are used like sterilization of medical waste and medical products, food irradiation or decontamination of sewage. For these processes a high power is required to achieve a high product throughput in a plant. The aim is therefore to use beam powers of around 100 kW or more. Since the applications of electron accelerators in industrial environments are steadily increasing one can speculate about transferring the above named state of the arte technology to industrial electron accelerators. At the FZR a feasibility study of such a table top electron accelerator (TTE) has been performed to investigate its technical limits and marketabilitys.