This diploma thesis deals with a study of low-profile directional antennas, followed by design and optimization of parabolic reflector antenna in centimeter and millimeter band. The first part of this work is focused on the analysis of several kinds of directional antennas, mainly on parabolic reflector and on SIW technology, which will be used for final antenna realization. The next part of this project is about the particular concept of the substrate integrated parabolic antenna for 60 GHz ISM band, its simulation and optimization in the CST Microwave Studio software. The final part of this thesis is devoted to the results achieved.

Background and Purpose: Flow diversion is increasingly used as an endovascular treatment for intracranial aneurysms. In this retrospective multicenter study, we analyzed the safety and efficacy of the treatment of intracranial, unruptured, or previously treated but recanalized aneurysms using Flow Re-Direction Endoluminal Device (FRED) Jr with emphasis on midterm results. Materials and Methods: Clinical and radiological records of 150 patients harboring 159 aneurysms treated with FRED Jr at six centers between October 2014 and February 2020 were reviewed and consecutively included. Clinical outcome was measured by using the modified Rankin Scale (mRS). Anatomical results were assessed according to the O’Kelly-Marotta (OKM) scale and the Cekirge-Saatci Classification (CSC) scale. Results: The overall complication rate was 24/159 (16%). Thrombotic-ischemic events occurred in 18/159 treatments (11%). These resulted in long-term neurological sequelae in two patients (1%) with worsening from pre-treatment mRS 0–2 and mRS 4 after treatment. Complete or near-complete occlusion of the treated aneurysm according to the OKM scale was reached in 54% (85/158) at 6-month, in 68% (90/133) at 1-year, and in 83% (77/93) at 2-year follow-up, respectively. The rates of narrowing or occlusion of a vessel branch originating from the treated aneurysm according to the CSC scale were 11% (12/108) at 6-month, 20% (17/87) at 1-year, and 23% (13/57) at 2-year follow-up, respectively, with all cases being asymptomatic. Conclusions: In this retrospective multicenter study, FRED Jr was safe and effective in the midterm occlusion of cerebral aneurysms. Most importantly, it was associated with a high rate of good clinical outcome.

No description available.

No description available.

Dual-band antenna elements that support dual-polarization provide ideal performance for applications including space-based platforms, multifunction radar, wireless communications, and personal electronic devices. In many communications and radar applications, a dual-band, dual-polarization antenna array becomes a requirement in order to produce an electronically steerable, directional beam capable of supporting multiple functions. The multiple polarizations and frequency bands allow the array to generate multiple simultaneous beams to support true multifunction radar. Many of the applications in spaced-based systems and personal electronic devices have strict restraints on the size and weight of the antenna element, favoring a low-profile, lightweight device. The research performed in this dissertation focuses on the design of a dual-band, dual-polarized antenna element capable of operating as an isolated element or in an array environment. The element contains two concentric, dual-polarized radiators. The low band radiator is a shorted square ring antenna, and the high band radiator is a square ring slot. Each constituent element achieves circular polarization through the introduction of triangular perturbations into opposing corners of the radiating element. This technique has been shown to introduce two, near-degenerate modes in the structure that – when excited in phase quadrature – combine to form circular polarization. The perturbations allow circular polarized operation with only a single feed point. The sense of the circular polarization is determined by the location of the feed point with respect to the perturbations. Both senses of circular polarization are excited by the introduction of orthogonal feeds for each of the two radiating elements. Thus, dual-ban, dual-circular polarization is obtained. The element achieves a low-profile from its printed circuit board realization. The high band square ring slot is realized in stripline. The orthogonal feeding transmission lines are printed on opposing sides of an electrically thin dielectric layer to allow them to cross without physically intersecting. This thin feeding substrate is sandwiched between two dielectric layers of matched dielectric constant. A ground plane is located on the top and bottom of the sandwiched dielectric structure, and the top ground plane contains the square ring slot with perturbed corners. Slotted stripline structures have been shown in the literature to excite a parallel-plate mode that can degrade overall performance of the antenna. Plated through holes are introduced at the outer perimeter of the square ring slot to short out this parallel-plate mode. The plated through holes (also called vias) serve as the shorting mechanism for the low band microstrip shorted square ring radiator. This element also contains triangular perturbations at opposing corners to excite circular polarization with a single feed point. In this element, orthogonal probe feeds are present to excite both senses of circular polarization. A dual-band, dual-polarized antenna element was built, tested, and compared to simulations. The constructed element operated at two distinct industrial, scientific, and medical (ISM) frequency bands due to their popularity in low power communications. The antenna element was realized in a multilayer printed circuit layout. A complex design procedure was developed and submitted to a printed circuit board company who manufactured the antenna element. The s-parameters of the antenna were measured using a Network Analyzer, and the results show good agreement with simulations. The radiation and polarization characteristics were measured in a compact range facility. These results also agreed well with simulations. The measured results verify the simulation models that were used in the simulations and establish a confidence level in the feasibility of constructing this element. The dual-band, dual-polarization nature of this element was established through the construction and measurement of this element. A novel size reduction technique was developed that allows for significant reduction of the element's footprint. This size reduction facilitates the placement of this element within an array environment. The loading technique utilizes a structure analogous to a parallel-plate capacitor to drastically reduce the overall size of the low frequency shorted square ring. The loading structure uses a substrate that is separate from that of the radiating elements. This allows the load to use a high dielectric material to achieve a high capacitance without requiring the radiating elements to be printed on high dielectric material that is potentially expensive and lossy at microwave frequencies. The two frequency bands were selected to be in separate industrial, scientific, and medical (ISM) bands. These frequency bands are increasingly popular in low power communication devices because unlicensed operation is permitted. The 2.45 GHz and 5.8 GHz ISM bands are commonly used for applications including Bluetooth technology, multiple 801.11 protocol, cellular phone technology, and cordless phones. The ISM bands were chosen for this antenna element due to their popularity, but this antenna is not restricted to these bands. The frequency ratio can be altered by controlling the dielectric constant used in the printed circuit board design, the parameters of the capacitive loading structure, and the size of the constituent elements that are used. After the size reduction technique is applied, the dual-band, dual-polarized elements can be placed in an array environment resulting in an array capable of generating both senses of circular polarization in the two, distinct ISM bands. This provides an aperture capable of supporting multiple functions. Depending on the applications required, the frequency bands of the antenna element can be altered to suit the particular system needs. The array analysis performed in this dissertation used a unique hybrid calculation technique that utilizes nine active element patterns to represent the patterns of the individual elements within a large antenna array. A common first look at array performance is achieved by multiplying the element pattern of an isolated element by an array factor containing the contributions of the geometrical arrangement of the antenna elements. This technique neglects mutual coupling between elements in the array that can alter the impedance match and radiation characteristics of the elements in the array. The active element pattern defines the radiation pattern of a given element in an array when all other elements are terminated in a matched impedance load. The active element pattern is unique for each element in an array. When these patterns are summed, the exact array pattern is obtained. While this technique has the advantage of accuracy, it is not ideal because it requires the simulation, calculation, or measurement of the pattern for each element in the array environment. The technique developed in this dissertation uses only nine active element patterns. These elements are then assigned to represent the active element patterns for all elements in the array depending on the geometrical region where the given element resides. This technique provides a compromise between the speed of using a single element pattern and the accuracy of using the unique active element pattern for each element in the array. The application of these two concentric, coplanar radiators along with the capacitive loading technique provides a unique contribution to the field of antenna engineering. The majority of dual-band antenna elements in the literature operate with a single polarization in each band. The ones that operate with dual-polarization in each band are typically limited to dual-linear polarization. Circular polarization is preferable to linear in many applications because it allows flexible orientation between the transmitting antenna and receiving antenna in a communications system, while also mitigating multipath effects that lead to signal fading. The ability to operate with two, orthogonal senses of circular polarization allows a system to reuse frequencies and double system capacity without requiring additional bandwidth. The uniqueness of this element lies in its ability to provide dual-circular polarization in two separate frequency bands for an individual element or an antenna array environment. The arrangement of the two element geometries with the addition of the novel capacitive loading technique is also unique. The performance of this element is achieved while maintaining the light weight, low profile design that is critical for many wireless communications applications. This dissertation provides a detailed description of the operation of this dual-band, dual-polarized antenna element. The design of the constituent elements is discussed for several polarization configurations to establish an understanding of the building blocks for this element. The dual-band, dual-polarized element is presented in detail to show the impedance match, isolation, and axial ratio performance. The capacitive loading technique is applied to the dual-band, dual-polarized element, and the performance with the loading in place is compared to the performance of the unloaded element. Next, there is an in-depth description of the array calculation technique that was developed to incorporate mutual coupling effects into the array calculations. This technique is then applied to the dual-band, dual-polarized array to show the performance of several array sizes. / Ph. D.

Point-of-load (POL) converters are used extensively in IT products. Every piece of the integrated circuit (IC) is powered by a point-of-load (POL) converter, where the proximity of the power supply to the load is very critical in terms of transient performance and efficiency. A compact POL converter with high power density is desired because of current trends toward reducing the size and increasing functionalities of all forms of IT products and portable electronics. To improve the power density, a 3D integrated POL module has been successfully demonstrated at the Center for Power Electronic Systems (CPES) at Virginia Tech. While some challenges still need to be addressed, this research begins by improving the 3D integrated POL module with a reduced DCR for higher efficiency, the vertical module design for a smaller footprint occupation, and the hybrid core structure for non-linear inductance control. Moreover, as an important category of the POL converter, the voltage regulator (VR) serves an important role in powering processors in today's electronics. The multi-core processors are widely used in almost all kinds of CPUs, ranging from the big servers in data centers to the small smartphones in almost everyone's pocket. When powering multiple processor cores, the energy consumption can be reduced dramatically if the supply voltage can be modulated rapidly based on the power demand of each core by dynamic voltage and frequency scaling (DVFS). However, traditional discrete voltage regulators (VRs) are not able to realize the full potential of DVFS since they are not able to modulate the supply voltage fast enough due to their relatively low switching frequency and the high parasitic interconnect impedance between the VRs and the processors. With these discrete VRs, DVFS has only been applied at a coarse timescale, which can scale voltage levels only in tens of microseconds (which is normally called a coarse-grained DVFS). In order to get the full benefit of DVFS, a concept of an integrated voltage regulator (IVR) is proposed to allow fine-grained DVFS to scale voltage levels in less than a microsecond. Significant interest from both academia and industry has been drawn to IVR research. Recently, Intel has implemented two generations of very high frequency IVR. The first generation is implemented in Haswell processors, where air core inductors are integrated in the processor's packaging substrate and placed very closely to the processor die. The air core inductors have very limited ability in confining the high frequency magnetic flux noise generated by the very high switching frequency of 140MHz. In the second generation IVR in Broadwell processors, the inductors are moved away from the processor substrate to the 3DL PCB modules in the motherboard level under the die. Besides computers, small portable electronics such as smartphones are another application that can be greatly helped by IVRs. The smartphone market size is now larger than 400 billion US dollars, and its power consumption is becoming higher and higher as the functionality of smartphones continuously advances. Today's multi-phase VR for smartphone processors is built with a power management integrated circuit (PMIC) with discrete inductors. Today's smartphone VRs operate at 2-8MHz, but the discrete inductor is still bulky, and the VR is not close enough to the processor to support fine-grained DVFS. If the IVR solution can be extended to the smartphone platform, not only can the battery life be greatly improved, but the total power consumption of the smartphone (and associated charging time and charging safety issues) can also be significantly reduced. Intel's IVR may be a viable solution for computing applications, but the air core inductor with un-confined high-frequency magnetic flux would cause very severe problems for smartphones, which have even less of a space budget. This work proposes a three-dimensional (3D) integrated voltage regulator (IVR) structure for smartphone platforms. The proposed 3D IVR will operate with a frequency of tens of MHz. Instead of using an air core, a high-frequency magnetic core without an air gap is applied to confine the very high frequency flux. The inductor is designed with an ultra-low profile and a small footprint to fit the stringent space requirement of smartphones. A major challenge in the development of the very high frequency IVR inductor is to accurately characterize and compare magnetic materials in the tens of MHz frequency range. Despite the many existing works in this area, the reported measured properties of the magnetics are still very limited and indirect. In regards to permeability, although its value at different frequencies is often reported, its saturation property in real DC-biased working conditions still lacks investigation. In terms of loss property, the previous works usually show the equivalent resistance value only, which is usually measured with small-signal excitation from an impedance/network analyzer and is not able to represent the real magnetic core loss under large-signal excitation in working conditions. The lack of magnetic properties in real working conditions in previous works is due to the significant challenges in the magnetic characterization technique at very high frequencies, and it is a major obstacle to accurately designing and testing the IVR inductors. In this research, an advanced core loss measurement method is proposed for very high frequency (tens of MHz) magnetic characterization for the IVR inductor design. The issues of and solutions for the permeability and loss measurement are demonstrated. The LTCC and NEC flake materials are characterized and compared up to 40MHz for IVR application. Based on the characterized material properties, both single-phase and multi-phase integrated inductor are designed, fabricated and experimentally tested in 20MHz buck converters, featuring a simple single-via winding structure, small size, ultra-low profile, ultra-low DCR, high current-handling ability, air-gap-free magnetics, multi-phase integration within one magnetic core, and lateral non-uniform flux distribution. It is found that the magnetic core operates at unusually high core loss density, while it is thermally manageable. The PCB copper can effectively dissipate inductor heat with 3D integration. In addition, new GaN device drivers and magnetic materials are evaluated and demonstrated with the ability to increase the IVR frequency to 30MHz and realize a higher density with a smaller loss. In summary, this research starts with improving the 3D integrated POL module, and then explores the use of the 3D integration technique along with the very high frequency IVR concept to power the smartphone processor. The challenges in a very high frequency magnetic characterization are addressed with a novel core loss measurement method capable of 40MHz loss characterization. The very high frequency multi-phase inductor integrated within one magnetic component is designed and demonstrated for the first time. A 20MHz IVR platform is built and the feasibility of the concept is experimentally verified. Finally, new GaN device drivers and magnetic materials are evaluated and demonstrated with the ability to increase the IVR frequency to 30MHz and realize higher density with smaller loss. / Ph. D. / This research focuses on reducing the size, footprint, and power loss of the power supply for the CPUs in different applications, ranging from the big servers in data centers to the small smartphones in almost everyone’s pocket. To achieve this goal, novel characterization, design, and integration technique is developed, especially for the bulky magnetic components, with much faster (~10X) switching speed than the nowadays practice. This research opens the door to the development of the next generation of CPUs’ power supply with very high switching speed, simple structure, high integration level, and high current handling ability.

Wearable technology has attracted global attention in the last decade and the market is experiencing an unprecedented growth. Wearable devices are designed to be low-profile, light-weight and integrated seamlessly into daily life. Comfort is one of the most important requirements for wearable devices. Fabric based antennas are soft, flexible and can be integrated into clothing. State of the art textile manufacturing techniques such as embroidery, combined with advanced conductive textile materials can be used to fabricate flexible fabric based on-body antennas. In this thesis, the feasibility of using computerised embroidery in the fabrication of wearable, flexible yet functional fabric based antennas have been examined. The fabric based antennas are embroidered using conductive threads. The most suitable materials for fabricating embroidered antennas have been identified. The embroidered fabric based antenna systems including transmission lines and low-profile detachable connectors have been fabricated and their RF performances have been tested. The optimal manufacturing parameters related to embroidery such as stitch direction, spacing and length have been examined. The repeatability of embroidered antennas, cost estimation, and complexity of manufacturing process have been clearly presented. The results can be used to inform and provide guidelines for the development of representative products that can be mass manufactured. A new simulation approach has been introduced to analyse the anisotropic properties of embroidered conductive threads. Simulations and measurements indicate that the performances of embroidered antennas are affected by the anisotropic surface current due to the embroidered stitches. Exploiting the current direction, a novel non-uniform meshed patch antenna has been designed. Representative results show that the non-uniform meshed structure can significantly reduce more than 75% of the usage of conductive materials for the microstrip antennas with negligible effect on the antenna performance.

The aim of this diploma thesis is to study the possibilities and problems of low-profile antennas and subsequently to design a directional antenna with spherical reflector for millimeter wavelengths. The theoretical part deals with basic information about horn and reflector antennas, and about SIW technology. In addition, the thesis deals with the specific design and modeling of the antenna using CST Microwave Studio. The simulated design achieved a sufficient bandwidth to cover ISM (57 GHz to 64 GHz) with gain 13.6 dBi at 60 GHz frequency. On fabricated antenna, the antenna impedance ratios were worse and the target bandwidth was not reached. Antenna gain was 14.33 dBi at 60 GHz frequency.

This diploma thesis describes the corrugated substrate integrated horn antenna designed to surface wave’s excitation in the UWB band groups 3, 4, 5 and 6 (6 – 10 GHz). The antenna is integrated into 3,4 mm thick textile with relative permittivity r = 1,195. The coaxial cable is connected via the SMA connector that is attached to the aluminum bracket. From the microstrip line transition the corrugated substrate integrated waveguide is excited. Two strip lines are placed in front of the aperture for improvement of the impedance matching. The directivity of the antenna is 12 dBi at 8 GHz. At the same frequency, the antenna efficiency is 70%.

The design of a low cost electronically steered array feed (ESAF) is implemented and tested. The ESAF demonstrated satellite tracking capabilities over four degrees. The system was compared to a commercial low-noise block downconverter (LNBF) and was able to receive the signal over a wider angle than the commercial system. Its signal-to-noise ratio (SNR) performance was poor, but a proof of concept for a low cost ESAF used for tracking is demonstrated. Two compact low profile dual circularly polarized (CP) reflector feed antenna designs are also analyzed. One of the designs is a passive antenna dipole array over an electromagnetic band gap (EBG) surface. It demonstrated high isolation between ports for orthogonal polarizations while also achieving quality dual CP performance. Simulations and measurements are shown for this antenna. The other antenna was a microstrip cross antenna. This antenna demonstrated high gain and quality CP but had a large side lobe and low isolation between ports. A global positioning system (GPS) denied multiple input multiple output (MIMO) radar for unmanned aerial vehicles (UAVs) is simulated and tested in a physical optics scattering model. This model is developed and tested by comparing simulated and analytical results. The radar uses channel matrices generated from the MIMO antenna system. The channel matrices are then used to generate correlation matrices. A matrix distance between actively received correlation matrices to stored correlation matrices is used to estimate the position of the UAV. Simulations demonstrate the ability of the radar algorithm to determine its position when flying along a previously mapped path.