Today's microwave circuits, whether for communication, radar, or testing systems, need compact tunable microwave filters. Since different microwave circuit applications have radically different size, power, insertion loss, rejection, vibration, and thermal requirements, new filter technologies with different balances between these requirements are always desirable. Negative Refractive Index (NRI) transmission media was discovered 10 years ago with the unique property of negative phase propagation. A literature review was conducted to identify potential NRI methods for filters and other devices, but no NRI tunable filters were found. To address this gap, a family of tunable NRI bandpass filters was simulated and constructed successfully using end-coupled zeroth order resonators. Tuning was accomplished by controlling the negative phase length of the NRI sections with varactors. The resulting L-band filters exhibited a 25-40 percent tunable range, no higher order resonances, and required only one fourth the length of a coupled-line filter constructed from traditional 180 degree microstrip resonators.

A full wave finite-difference time-domain method (FDTD) combined with thin-wire and thin-slot algorithms to analyze a metamaterial fabricated with periodic mushroom structures, is proposed in this dissertation. This proposed method is suitable for analyzing problems involving large structures with fine structural details. A periodic analysis for mushroom structures is presented. Only a single unit mushroom cell is required to present the phenomena of infinite periodicity with the help of periodic boundary conditions (PBCs). The composite right-/left-handed (CRLH) transmission line (TL) approach is introduced and used to approximate CRLH metamaterial through lumped L and C. Finally, several CRLH metamaterial mushroom-based structures are investigated. A 19 by 8 flat microwave lens and a parabolic microwave lens structure composed of 410 unit mushroom cells are investigated. These structures demonstrate negative refractive index (NRI) characteristics while operate in the left-hand (LH) region. The simulation and measurement results of one- and two-dimensional CRLH mushroom-based structures are compared.

This work demonstrates the effectiveness of coextrusion as a method to manufacture negative stiffness inclusions for use in vibrational damping applications. The theory and mechanics of negative stiffness and coextrusion are introduced and the process of creating and extruding a feed rod with negative stiffness architecture explained. Coextrusion is shown to be a viable method to create negative stiffness inclusions / text

Photonic bandgap materials are periodic structures that exclude electromagnetic field propagation over frequency intervals known as bandgaps. These materials exhibit remarkable wave dispersion and have found use in many applications that require control over dynamic electromagnetic fields, as their properties can be tailored by design. The two principal objectives of this thesis are the development of a liquid crystal-based microwave photonic bandgap device whose bandgap could be tuned during operation and the design and implementation of a spectral transmission-line modeling method for band structure calculations. The description of computational methods comprises an overview of the implemented numerical routines, a derivation of the spectral properties of the transmission-line modeling method in periodic domains, and the development of an efficient sparse matrix eigenvalue algorithm that formed the basis of the spectral transmission-line modeling method. The discussion of experimental methods considers the use of liquid crystals in microwave applications and details the design and fabrication of several devices. These include a series of modified twisted nematic cells that were used to evaluate liquid crystal alignment and switching, a patch resonator that was used to measure liquid crystal permittivity, and the liquid crystal photonic bandgap device itself. Numerical experiments showed that the spectral transmission-line modeling method is accurate and substantially faster and less memory intensive than the reference plane wave method for problems of high dielectric contrast or rapidly varying spatial detail. Physical experiments successfully realized a microwave photonic bandgap structure whose bandgap could be continuously tuned with a bias voltage. The very good agreement between simulated and measured results validate the computational and experimental methods used, particularly the resonance-based technique for permittivity measurement. This work's results may be applied to many applications, including microwave filters, negative group velocity/negative refraction materials, and microwave permittivity measurement of liquid crystals.

Photonic bandgap materials are periodic structures that exclude electromagnetic field propagation over frequency intervals known as bandgaps. These materials exhibit remarkable wave dispersion and have found use in many applications that require control over dynamic electromagnetic fields, as their properties can be tailored by design. The two principal objectives of this thesis are the development of a liquid crystal-based microwave photonic bandgap device whose bandgap could be tuned during operation and the design and implementation of a spectral transmission-line modeling method for band structure calculations. The description of computational methods comprises an overview of the implemented numerical routines, a derivation of the spectral properties of the transmission-line modeling method in periodic domains, and the development of an efficient sparse matrix eigenvalue algorithm that formed the basis of the spectral transmission-line modeling method. The discussion of experimental methods considers the use of liquid crystals in microwave applications and details the design and fabrication of several devices. These include a series of modified twisted nematic cells that were used to evaluate liquid crystal alignment and switching, a patch resonator that was used to measure liquid crystal permittivity, and the liquid crystal photonic bandgap device itself. Numerical experiments showed that the spectral transmission-line modeling method is accurate and substantially faster and less memory intensive than the reference plane wave method for problems of high dielectric contrast or rapidly varying spatial detail. Physical experiments successfully realized a microwave photonic bandgap structure whose bandgap could be continuously tuned with a bias voltage. The very good agreement between simulated and measured results validate the computational and experimental methods used, particularly the resonance-based technique for permittivity measurement. This work's results may be applied to many applications, including microwave filters, negative group velocity/negative refraction materials, and microwave permittivity measurement of liquid crystals.

京都大学 / 0048 / 新制・論文博士 / 博士(工学) / 乙第12984号 / 論工博第4131号 / 新制||工||1637(附属図書館) / 32454 / 京都大学大学院工学研究科電子物性工学専攻 / (主査)教授 北野 正雄, 教授 竹内 繁樹, 准教授 久門 尚史 / 学位規則第4条第2項該当 / Doctor of Philosophy (Engineering) / Kyoto University / DFAM

京都大学 / 0048 / 新制・課程博士 / 博士(工学) / 甲第20380号 / 工博第4317号 / 新制||工||1669(附属図書館) / 京都大学大学院工学研究科電子工学専攻 / (主査)教授 北野 正雄, 教授 山田 啓文, 教授 松尾 哲司 / 学位規則第4条第1項該当 / Doctor of Philosophy (Engineering) / Kyoto University / DFAM

Nikolai Tesla's revolutionary experiments demonstrated the possible benefits of transmitting power wirelessly as early as 1891. Applications for the military, consumers, emergency personnel, remote sensors, and others use Tesla’s discovery of wireless power. Wireless power transmission (WPT) has the potential to be a common source of consumable energy, but it will only receive serious consideration if the transmit and receive systems are extremely efficient and capable of delivering usable amounts of power. Research has been conducted to improve the efficiency and performance of nearly every aspect of WPT systems, but the relatively new field of metamaterials (MTMs) has yet to play a dominate role in improving system performance. A gradient index (GRIN) MTM lens was designed using Ansoft’s High Frequency Structure Simulator (HFSS) to improve antenna gain and thereby increase WPT system performance. A simple WPT demonstration system using microstrip patch antennas (MPAs) confirmed the benefits of the GRIN MTM lens. The WPT demonstration system, MPAs, and GRIN MTM lens were constructed and experimentally tested near 2.45 GHz. The theoretical and experimental gain improvement of the MPA due to the GRIN MTM lens is 5.91 dB and 7.06 dB, respectively.

Efficient absorption of light is required for a large number of applications such as thermo-photovoltaics,thermal imaging, bio-sensing, thermal emitters, astronomy, and stealth technology. Strong light absorbers found in nature with high intrinsic losses such as carbon black, metal-black, and carbon nano-tubes etc. are bulky, not design-tunable and are hard to pattern for micro- and nano- devices. We developed thin-film, high performance absorbers in the visible, near-, mid-, long-wave - and far-IR region based on a 3 layer metal-dielectric-metal (MDM) structure. We fabricated a 3-layerMDMabsorber with large band-widths in the visible and near IR spectral range without any lithographic patterning. This was the first demonstration in the optical range of the Salisbury Screen, which was originally invented for radar absorption. A Fabry-Perot cavity model depending on the thickness of the dielectric, but also the effective permittivity of the semi-transparent top metal gives calculated spectra that agree well with experiment. Secondly, we fabricated long-wave IR and far-IR MDM absorbers comprising surface patterns of periodic metal squares on the dielectric layer. Strong absorption in multiple bands were obtained, and these depended weakly on polarization and angle of incidence. Though such absorbers had been extensively studied by electrodynamic simulations and experiment in the visible to far- R regions, there existed no analytic model that could accurately predict the wavelengths of the multiple resonances. We developed a theoretical model for these absorbers based on standingwave resonances, which accurately predicts resonance wavelengths for experiment and simulation for the first time. Unlike metamaterial theories our model does not depend on the periodicity of the squares but only on their lateral dimension and the thickness of the dielectric. This feature is confirmed by synchrotron-based IR spectral imaging microscopy of single isolated squares.

Yes / A novel 50μm Silicon-based on-chip antenna is presented that combines metamaterial (MTM) and substrate integrated waveguide (SIW) technologies for integration in THz circuits operating from 0.28 to 0.30 THz. The antenna structure comprises a square patch antenna implemented on a Silicon substrate with a ground-plane. Embedded diagonally in the patch are two T-shaped slots and the edges of the patch is short-circuited to the ground-plane with metal vias, which convert the structure into a substrate integrated waveguide. This structure reduces loss resulting from surface waves and Silicon dielectric substrate. The modes in the structure can be excited through two coaxial ports connected to the patch from the underside of the Silicon substrate. The proposed antenna structure is essentially transformed to exhibit metamaterial properties by realizing two T-shaped slots, which enlarges the effective aperture area of the miniature antenna and significantly enhances its impedance bandwidth and radiation characteristics between 0.28 THz to 0.3 THz. It has an average gain and efficiency of 4.5dBi and 65%, respectively. In addition, it is a self-isolated structure with high isolation of better than 30dB between the two ports. The on-chip antenna has dimensions of 800×800×60 μm3. / H2020-MSCA-ITN-2016 SECRET-722424 and the financial support from the UK Engineering and Physical Sciences Research Council (EPSRC) under grant EP/E0/22936/1