The content of this dissertation is to utilize foundations of heat consumption in Velký Karlov and to propose and replace the main district heating plant into the heating plant which uses biomass as its fuel. With techno-economic evaluation of the annual operating central heating plant evaluate the suitability of using a steam turbine or steam engine. The proposal for a steam turbine is chosen by the preliminary calculation. There are showed suitable possibilities of working and its evaluation considered to return period.

The aim of the work is to design a plain wood combustion boiler of 60 t/h output. Fuelling component analysis has been added to the basic boiler parameters. Stechiometric calculations were performed for given fuel composition. Thermal efficiency was set after making thermal balance. Separate convective areas and boiler proportions were designed together with separate steam output parameters (temperature, pressure, amount). Design documentation was added.

The content of this diploma thesis is proposal of repair, reconstruction of equipment and installation of electrohydraulic regulation of steam turbine. Thesis is given for specific case. At the beginning there is a basic description of repairing turbine. The next part of thesis deals with checking of main turbine parts and recalculation of gland steam. In the following part there is revisional report with repair or exchange suggestions of demaged turbine parts, followed by description of turbine regulation reconstruction. The last part deals with economical evaluation used innovation and recommendations for repairment procedure.

The work is focused on the design heat generation source in my chosen location. The entire facility should be designed to meet the basic requirements of the client. The primary objective of this work is alternatively propose solutions to perform basic balance calculations and determine the performance of each device. Based on the location selected diagram to produce annual heat needs and recommend the best possible solution.

The present diploma thesis "Animated models of heat engines" describes the design of an interactive application. The theoretical part deals with the classification of heat engines and their rotations. The result of the present diploma thesis is the new application "Animation of heat engines" designed in Flash programme. This application is focused on the basic function principle of four demonstrated engines. The present work also deals with assessing and comparison of real engines, their cuts, real models and animated engines.

The purpose of the thesis is to create a model for an analysis of a steam conditioning valve whose function is to reduce the temperature of the steam using a spray water system. First of all, simulation of the fluid flow and heat transfer is done using CFD analysis. Then the results are used for thermal stress calculation.

This thesis concerns with recalculation of steam boiler. Arrangement for reaching of new steam boiler parameters and temperature of combustion gases was suggested at first. Then it was verified with thermal calculation, all necessities included.

Thesis deals with oil-turbine frame of the model SST 300 SST 400. This work is divided into several parts. Beginning of this thesis deals with a description of the problem and the oil economy. Next part is concerned with 3D design model of the oil tank in the program ProEngineer Wildfire 2.0. Final part describes a creation of manufacturing drawings with BOMs. In conclusion, the thesis presents the results of additional topics, such as a computational model in Ansys 11 and making the calculation of tension or bonds in an oil suspension in the frame. The result of this work is the full-fledged design of the weldment of oil frame, which was submitted for approval to the Siemens Company, which will continue in the subproject tasks of new turbo model SST 300 pattern SST 400.

The aim of this thesis is to analyze the heat transfer in steam generator of blocks in the nuclear power plant VVER 440. The steam generator represents the border between the primary and the secondary circuit. The heat is carried from a warm water from reactor to a cold water. The steam arises after the heat transfer and drives the steam turbine. An important quantity which represents the heat transfer is a heat transfer factor. This thesis is divided into theoretical and a practical part. In the theoretical part is mentioned a principle of the steam generator and the theoretical calculation of the heat transfer factor, which comes first of all from the character of the streaming in the steam generator. The practical part brings a comparison of the heat transfer factor calculated from data measured after the start of the third block of EDU in 1986, with the heat transfer factor which comes from the measurement after the power-increase for 105 % of nominal power of the same block in 2009. Further is shown the prediction of the heat transfer factor for next power-increase and the following service is shown too.

The Diploma Thesis deals with a design of a backpressure turbine without any bleeds. The fundament of the Diploma Thesis is a thermodynamical calculation of particular parts of the turbine. Technical solutions are designed according to given details of a steam and chosen conditions of use.