The thesis aims to provide an evaluation on the Volvo 1/5th scaled wind tunnel regarding its potentials and capabilities in aerodynamic study. The flow quality in the test section was evaluated. The experiments were performed included measurements of airspeed stability, tunnel-wall boundary layer profile and horizontal buoyancy. A numerical model was developed to predict the boundary layer thickness on the test floor. Repeatability tests were also conducted to establish the appropriate operating regime.A correlation study between the 1/5th scaled wind tunnel (MWT) and full scale wind tunnel (PVT) was performed using steady force and unsteady pressure measurements. The Volvo Aero 2020 concept car was selected to be the test model.The Reynolds effect and the tunnel-wall boundary layer interference were identified in the steady force measurements. Unsteady near-wake phenomena such as wake pumping and wake flapping were discussed in the unsteady base pressure measurements.

Turbulent boundary layers flowing over a smooth surface were studied to understand the influence of varying pressure gradients and flow Reynolds number on the boundary layer growth and mean turbulent properties. The test was conducted in the Virginia Tech Stability Wind Tunnel with a 0.914 m chord length, NACA 0012 Airfoil in the test section. This airfoil was rotated to different angles of attack to induce varying pressure gradients on the boundary layer developing on the test section walls. Mean pressure measurements, boundary layer pressure measurements, and time-resolved, wall-normal, stereoscopic particle image velocimetry (TR-PIV) measurements were made. The TR-PIV data was acquired at a chord-based Reynolds number of 1.2 million, 2 million, and 3.5 million, at a sampling rate of 1 kHz, in two different camera configurations. The boundary layer pressure measurements were acquired at different flow Reynolds numbers ranging between 0.76 million and 3.5 million. Both adverse and favorable pressure gradients of varying intensities were imposed on the boundary layer by rotating a 0.914 m chord NACA 0012 airfoil to angles of attacks between -{10}^o and {12}^o. Measurements at varying streamwise locations enabled the study of boundary layer flow development under changing pressure gradients. The pressure gradient influences were observed in the boundary layer characteristic properties, on the mean velocities, and on the Reynolds stresses present in the flow. The pressure gradient influences were found to be consistent at varying Reynolds numbers, but the intensity of their effects was influenced by the flow Reynolds number. Moreover, the influence of pressure gradients and flow Reynolds numbers was evident in both outer and inner scales. The test data acquired was also validated with previous works. / M.S. / The interaction of turbulent boundary layers and smooth surfaces is prevalent in our world. It plays a vital role in various phenomena, such as, aircraft stall, cabin noise, and structural vibrations. Varying flow conditions influence the behavior of boundary layers and the extent of their implications. The effects of pressure gradients and the level of turbulence, described by the Reynolds numbers, on turbulent boundary layer flow was studied. This was done through an experiment conducted at the Virginia Tech Stability Wind Tunnel facility. The test data was acquired through boundary layer pressure measurements and Time-Resolved, Stereoscopic Particle Image Velocimetry (TR-PIV) at varying streamwise locations in the test section. A 0.914 m chord, NACA 0012 airfoil was placed in the test section and its angle of attack was varied to -{10}^o,0^o,\ \ and\ {12}^o to induce a favorable, minimum, and an adverse pressure gradient, respectively. The TR-PIV measurements were acquired at a sampling rate of 1 kHz and in two different camera configurations. The flow Reynolds number was based on the airfoil chord length (Re_c) and was varied to 1.2 million, 2 million, and 3.5 million for the TR-PIV tests. The boundary layer pressure measurements were acquired using an array of 30 Pitot probes placed in the boundary layer of the flow. The flow Reynolds number for these test runs ranged between 0.76 million and 3.5 million. The acquired data was used to analyze the mean statistical properties of turbulent boundary layers primarily focusing on the mean velocities, boundary characteristic parameters, Reynolds normal stresses, and Reynolds shear stresses. The results showed that the nature of pressure gradient influences on the mean properties of turbulent boundary layers remained consistent regardless of the flow Reynolds number. However, the intensity of the pressure gradient effects was influenced by the flow Reynolds number. These observations were made at various streamwise data acquisition locations through which the evolution of the flow was also studied. Lastly, the results obtained in this experiment were validated with previous works.

When an aircraft is aerodynamically or structurally damaged in battle, it may not able to complete the mission and the damage may cause its loss. The subject of aircraft battle survivability is one of critical concern to many disciplines, whether military or civil. This thesis considered and focused on Computational Fluid Dynamics [CFD] predictions and experimental investigations into the effects of simulated battle damage on the low-speed aerodynamics of a fmite aspect ratio wing. Results showed that in two-dimensional [2d] and three-dimensional [3D] CFD simulations, Fluent's® models work reasonably well in predicting jets flow structures, pressure distributions, and pressure-coefficient Cp's contours but not for aerodynamic coefficients. The consequences were therefore that CFD prediction was poor on aerodynamic-coefficients increments. The prediction of Cp's achieved good agreement upstream and near the damage hole, but showed poor agreement at downstream of the hole. For the flow structure visualisation, at both weak and strong jet incidences, the solver always predicted pressure-distribution-coefficient lower at upstream and higher at downstream. The results showed relatively good agreement for the case of transitional and strong jet incidences but slightly poor for weak jet incidences. From the experimental results of Finite Wing, the increments for Aspect-ratio, AR6, AR8 and ARIO showed that as damage moves out towards the tip, aerodynamic-coefficients increments i.e. lift-loss and drag-rise decreased, and pitching-moment-coefficient increment indicated a more positive value at all incidence ranges and at all aspect ratios. Increasing the incidence resulted in greater magnitudes of lift-loss and drag-rise for all damage locations and aspect ratios. At the weak jet incidence 4° for AR8 and in all of the three damage locations, the main characteristics of the weak-jet were illustrated clearly. The increments were relatively small. Whilst at 8°, the flow structure was characterised as transitional to stronger-jet. In Finite Wing tests and for all damage locations, there was always a flow structure asymmetry. This was believed to be due to gravity, surface imperfection, and or genuine feature. An 'early strong jet' that indicated in Finite Wing-AR8 at 'transitional' incidence of 8°, also indicated in twodimensional results but at the weak-jet incidence of 4°. For the application of 2d data to AR6, AR8, and ARIO, an assessment of 2d force results led to the analysis that the tests in the AAE's Low Turbulence Tunnel for 2d were under-predicting the damage effects at low incidence, and over-predicting at high incidences. This suggested therefore that Irwin's 2d results could not be used immediately to predict three-dimensional.

The aerodynamic performance of low aspect ratio wings at low Reynolds numbers applicable to micro air vehicle design was studied in this thesis. There is an overall lack of data for this low Reynolds number range, particularly concerning details of local flow behavior along the span. Experiments were conducted to measure the local pressure distributions on a wing at various spanwise locations in a Reynolds number range 30000 < Re < 90000. The model wing consisted of numerous wing sections and had a rectangular planform with NACA0012 airfoil shape with aspect ratio of one. One wing section, with pressure ports at various chordwise locations, was placed at different spanwise locations on a wing to effectively obtain the local pressure information. Integration of the pressure distributions yielded the local lift coefficients. Comparison of the local lift distributions to optimal elliptic lift distribution was conducted. This comparison showed a sharply peaked lift distribution near the wing tip resulting in a drastic deviation from the equivalent elliptic lift distributions predicted by the finite wing theory. The local lift distributions were further analyzed to determine the total lift coefficients vs angle of attack curves, span efficiency factors and the induced drag coefficients. Measured span efficiency factors, which were lower than predictions of the elliptic wing theory, can be understood by studying deviations of measured lift from the elliptic lift distribution. We conclude that elliptic wing theory is not sufficient to predict these aerodynamic performance parameters. Overall, these local measurements provided a better understanding of the low Reynolds number aerodynamics of the low aspect ratio wings.

La thèse traite de recherches numériques et expérimentales sur l’écoulement à traves des conduites circulaires ou des tubes avec une petite entrée et un diamètre de sortie plus grand, parfois appelées élargissement ou divergents. L’écoulement dans un élargissement est globalement stable pour des nombres de Reynolds élevés. Ainsi la simulation numérique de ce type d’écoulement nécessite de grands domaines de calcul contenant la zone de recirculation, qui croît linéairement. En outre, les études expérimentales dans les élargissements brusques indiquent que la transition se produit à des nombres de Reynolds plus faibles que prévue par la théorie linéaire de stabilité. La raison pour cette transition précoce est due à la présence d’imperfections dans le dispositif expérimental, qui agit comme une perturbation d’amplitude finie de l’écoulement. Des simulations numériques directes des équations de Navier-Stokes ont été réalisées avec deux types différents de perturbations (i) l’inclination et (ii) le vortex. Tout d’abord, la perturbation de type inclinaison, qui est appliqué à l’entrée, crée une zone de recirculation asymétrique, puis se casse pour former une turbulence localisée en aval de l’expansion. Deuxièmement, la perturbation de type vortex, crée des structures qui ressemblent à un mode azimutal d’ordre inférieur, déjà identifié comme une perturbation optimale amplifiée. Il croît en raison de l’instabilité convective, puis forme une tâche de turbulence localisée. Enfin, la corrélation spatiale et la décomposition en modes propres révèlent que cette turbulence localisée obtient son énergie de l’écoulement d’entrée. / The thesis deals with numerical and experimental investigations of flow through circular pipes with smaller inlet and larger outlet diameter, also known as expansion pipes. The hydrodynamic expansion pipe flow is globally stable for high Reynolds number. In order to numerically simulate these types of flows, large computational domains that could accommodate the linearly growing symmetric recirculation region is needed. Moreover, experimental studies of expansion pipe flows indicate that the transition occurs at lower Reynolds number than predicted by the linear stability theory. The reason for early transition is due to the presence of imperfections in the experimental setup, which acts as a finite-amplitude perturbation of the flow. Three-dimensional direct numerical simulations of the Navier-Stokes equations with two different types of perturbations (i) the tilt and (ii) the vortex are investigated. First, the tilt perturbation, which applied at the inlet, creates an asymmetric recirculation region and then breaks to form localised turbulence downstream the expansion section. Second, the vortex perturbation, creates structures that looks like lower order azimuthal mode, resembles an optimally amplified perturbation. It grows due to convective instability mechanism and then breaks to form localised turbulence. Spatial correlation and the proper orthogonal decomposition reveal that this localised turbulence gains it energy from the core flow coming out of the inlet pipe.

Wind propulsion is a traditional way to propel ships over the oceans. In the recent development towards more sustainable shipping, sailing is considered in the industry again with high momentum. For a modern merchant ship, the aerodynamic forces generated on the particular rigging are unusual. Tailored research and experiments are required to understand their influence on the ship’s sailing behaviour. This work concerns the aerodynamic interactions on a model-sized car carrier with four 360° rotatable, symmetric, rigid wings aligned along the centreline on deck. Differential pressures on the wings are measured to capture the generated normal forces. In a comprehensive post-processing, data recorded in systematic experiments at two apparent wind angles were evaluated. A comparison for the different wing positions on board the model shows stronger interactions in upwind sailing conditions than when reaching. The two-dimensional data prove a significant influence of the hull in the normal force profiles over the wing span. The results of this work indicate that the aerodynamic conditions while sailing have to be attentively considered for efficient wing trimming. / Under en lång tid användes främst vindkraft för framdrivningen av fartyg. Det är först på senare år att seglingskonceptet har fått ett nytt uppsving inom marinindustrin med tanke på dess hållbarhet. För fraktfartyg är de aerodynamiska krafterna vid segling ovanliga. Därför behövs särskild forskning och experimentella metoder för att förstå hur de påverkar fartygens seglingsbeteende. I detta arbete undersöks aerodynamiska interaktioner på en modell av ett biltransportfartyg med fyra symmetriska, 360° roterbara vingsegel på däck längs midskeppslinjen. I systematiska experiment på två kurser mot vinden mättes differenstryck över vingprofilen för att undersöka de genererade normalkrafterna. En jämförelse av data från de fyra olika vingpositionerna och båda kurserna mot vinden visar att de aerodynamiska interaktionerna är starkare på kryss än vid halvvind. De upmätta profilerna av tvådimensionella normalkraftkoefficienter över vingspannet visar på betydande aerodynamiska interaktioner med fartygets skrov. Resultaten av detta arbete visar hur viktigt det är med en grundlig undersökning av strömningsförhållandena för en effektiv segeltrim.

Le présent travail concerne l'étude du décollement de coin de compresseurs par des investigations expérimentaux sur le banc d'essai subsonique grille d'aubes situé au LMFA (Re = 3.8 x 105, M = 0,12, profil NACA 65-009). Habituellement, cette particulière séparation tridimensionnelle a lieu dans le coin entre l'aubage et la paroi du moyeu des rangées d'aubes, également dans les stators et les rotors.Les performances de l’étage sont ainsi dégradées à cause des pertes de charge et du blocage conséquent à la séparation de l’écoulement. Bien que les caractéristiques stationnaires sont bien connues par la littérature, uniquement des récentes études expérimentales avancées combinées aux améliorations de simulations numériques, telles que URANS et LES, ont permis de découvrir le comportement très instable du décollement de coin. Des études préalables sur le même banc d'essai ont rapporté un comportement intermittent du décollement, appelé comportement bimodal. Dans la présente thèse de doctorat, il est montré que le comportement bimodal correspond à deux états spécifiques du champ fluide: une séparation fermée, presque supprimée, et une séparation ouverte caractérisée par un blocage massif. Il est clair que cette commutation bimodale du décollement de coin apparaissant dans une machine réelle pourrait avoir un impact fortement déstabilisant. En utilisant la méthode de mesure PIV haute vitesse couplée à des mesures de pression résolues en temps sur la surface de l'aubage, l'écoulement d'un canal inter-aube a été étudié pour deux différentes incidences. Les mesures PIV fournissent pour la première fois des visualisations résolues en temps et étendues à toute la section de l'aubage de la variation bimodale du décollement. L'interaction des grandes structures aléatoires de la couche limite à l'amont avec le bord d'attaque de l'aubage déstabilise le front du décollement et agrandit la région de recirculation. Une séparation ainsi massive persiste jusqu'à ce que le blocage dans le canal inter-aube provoque la rupture des plus grandes structures constituant la zone de recirculation. Successivement le débit recommence à accélérer et la séparation est presque supprimée. Cette dynamique coïncide avec le régime d'écoulement hautement instationnaire et apériodique des diffuseurs, appelé large transitory stall, caractérisé par des grandes amplitudes d'énergie dans la gamme des basses fréquences du spectre. Des moyennes conditionnelles de pression et la décomposition orthogonale modale (POD) des champs de vitesse ont été appliquées pour montrer l'effet rétroactif du blocage induit par la séparation ouverte sur l'angle local au bord d'attaque. Ces résultats supportent l’hypothèse d'une instabilité auto-entretenue causée par la diffusion imposée dans le stator. En fin, des mesures de pression totale résolues en temps ont été effectuées en utilisant des capteurs à haute réponse en fréquence, situés à la même position dans les différents canaux adjacents. La cohérence et la linéarité de l'angle de phase trouvée entre les capteurs confirment que l'instabilité du décollement peut se propager d'un canal a l'autre, en analogie avec les perturbations tournantes (rotating instabilities) apparaissant dans les bancs d'essai annulaires. Ceci montre pour la première fois que, même dans une grille d'aubes linéaire de compresseur, l'instabilité intrinsèque du décollement de coin peut déclencher la propagation d'instabilités. / The present work focuses on the study of the corner separation phenomenon in compressors carried out by experimental investigations on a subsonic linear cascade test rig (Re=3.8x105, M=0.12, blade profile NACA 65-009). Usually, this particular three-dimensional separation takes place in the corner between the blade and the endwall of compressor rows, mostly at hub, both in stators and rotors.Its main features are high total pressure losses and blockage of the flow, with consequent impacts on the efficiency. Whereas time averaged characteristics are well known from the past, only recent advanced experimental studies and improvements of numerical simulations, such as URANS and LES, have permitted to uncover the highly unsteady behavior of corner separation in compressors. Precedent studies on the same test rig have reported an intermittent unsteady behavior of corner separation, called bimodal behavior. In the present thesis it is shown that the bimodal behavior corresponds to two specific states of the flow: a closed separation, almost suppressed, and an open separation characterized by massive blockage and losses. Clearly hub-separation bimodal switches appearing in a real machine could have a first order detrimental effect on the stability of the flow in the compressor. By using high speed PIV coupled with unsteady pressure measurements on the surface of the blade the flow in a single blade passage has been investigated for different incidences. The PIV measurements provide, for the first time, time-resolved flow visualizations of the size switch of the separation with an extended field of view covering the entire blade section. The interaction of random large structures of the incoming boundary layer with the blade is found to be a predominant element that destabilizes the separation boundary and enlarges the recirculation region. Such a massive separation persists until the blockage in the passage causes the breakdown of the largest structures in the aft part of the blade, reestablishing the closed separation state. Such dynamics coincide with the aperiodic intermittent flow regime of diffusers, called transitory stall regime, and the associated Fourier spectra show the largest energy amplitudes in the low frequency range. Conditional ensemble averages of pressure and proper orthogonal decomposition (POD) of velocity fields have been applied to show the feedback effect of the blockage of the separation on the flow angle around the blade leading edge. These results draw the picture of a self-sustained instability caused by the diffusion imposed by the inter-blade passage. To answer the question about the interaction between adjacent corner separations, time-resolved total pressure measurements have been carried out by using high frequency response sensors positioned in bimodal points of multiple passages. The coherent propagation velocity and the linearity of the phase angle found between the signals confirm that the unsteadiness of the separation can propagate in pitch-wise direction. It is interesting to underline that equivalent elements characterize rotating disturbances appearing in annular test rigs. This finally shows that, even in an isolated stator blade row, the intrinsic unsteadiness of corner separation can start the propagation of instabilities. It is the first time that such a propagation effect is observed in a linear compressor cascade.

Le stockage d'hydrogène en phase solide sous forme d'hydrures, est l'une des solutions non-polluantes futures pour le stockage et le transport de l'énergie. Parmi les matériaux candidats, LiBH4 a été sélectionné vu sa capacité gravimétrique élevée en hydrogène (jusqu'à 13,6 % H2 en masse). Ce matériaux possède des propriétés thermodynamiques et cinétiques insuffisamment établies pour comprendre son comportement dans les applications futures. Sa décomposition peut être facilitée en présence de l'hydrure MgH2. Ainsi, le composite MgH2-xLiBH4 / Hydrides for solid-state hydrogen storage are one of the future solutions - pollutant free - for the storage and the transport of energy. Among the candidates, LiBH4 was selected considering its high gravimetric hydrogen capacity (up to 13.6 wt.% H2). This material has thermodynamic and kinetic properties insufficiently established to be included in future applications. Its decomposition can be facilitated within the presence of the hydride MgH2. Thus, the composite MgH2-xLiBH4 (0< x< 3.5) reactivated by high energy ball-milling, was studied regarding its microstructural properties and stability of the phases. The desorption reaction of hydrogen, with or without additives, shows the appearance of additional phases accompanying the principal reaction. Heat capacity measurements of LiBH4 revealed the presence of an abnormal behaviour before the polymorphous transition (Ttrs = 386 K), attributed to the increase of crystal defects in agreement with the existence of a hypo-stoichiometric domaine LiBH4-ε observed at higher temperatures. The stability of the three-phase system LiBH4-LiH-B was studied resulting to the principal reaction of decomposition: LiBH4(s,l) → LiH(s) + B(s) + 1,5H2(g). Vapour pressure measurements of LiBH4 showed that H2 is the major component of decomposition with minor species such as B2H6 and BH3. The thermodynamic properties of LiBH4 were critically assessed, gathering the new data with those existing in the literature, in the aim of modelling of reactions occurring in hydride mixtures.

Energy efficiency and renewable energy use are two main priorities leading to industrial sustainability nowadays according to European Steel Technology Platform (ESTP). Modernization efforts can be done by industries to improve energy consumptions of the production lines. These days, steel making industrial applications are energy and emission intensive. It was estimated that over the past years, energy consumption and corresponding CO2 generation has increased steadily reaching approximately 338.15 parts per million in august 2010 [1]. These kinds of facts and statistics have introduced a lot of room for improvement in energy efficiency for industrial applications through modernization and use of renewable energy sources such as solar Photovoltaic Systems (PV).The purpose of this thesis work is to make a preliminary design and simulation of the solar photovoltaic system which would attempt to cover the energy demand of the initial part of the pickling line hydraulic system at the SSAB steel plant. For this purpose, the energy consumptions of this hydraulic system would be studied and evaluated and a general analysis of the hydraulic and control components performance would be done which would yield a proper set of guidelines contributing towards future energy savings. The results of the energy efficiency analysis showed that the initial part of the pickling line hydraulic system worked with a low efficiency of 3.3%. Results of general analysis showed that hydraulic accumulators of 650 liter size should be used by the initial part pickling line system in combination with a one pump delivery of 100 l/min. Based on this, one PV system can deliver energy to an AC motor-pump set covering 17.6% of total energy and another PV system can supply a DC hydraulic pump substituting 26.7% of the demand. The first system used 290 m2 area of the roof and was sized as 40 kWp, the second used 109 m2 and was sized as 15.2 kWp. It was concluded that the reason for the low efficiency was the oversized design of the system. Incremental modernization efforts could help to improve the hydraulic system energy efficiency and make the design of the solar photovoltaic system realistically possible. Two types of PV systems where analyzed in the thesis work. A method was found calculating the load simulation sequence based on the energy efficiency studies to help in the PV system simulations. Hydraulic accumulators integrated into the pickling line worked as energy storage when being charged by the PV system as well.

Les instabilités aéroélastiques de bandes d’acier constituent aujourd’hui l’un des problèmes majeurs dans les sections de refroidissement par jets impactants des lignes de recuit continues.En effet, le traitement thermique des nouveaux aciers nécessite de très fortes pentes de température impliquant constamment des augmentations de vitesse de soufflage susceptibles de mettre en jeu des instabilités aéroélastiques. Des flottements ainsi que des divergences de bande ont déjà été constatées et identifiées. Ces deux instabilités impliquent dans la plupart des cas des chocs entre la bande et les buses de soufflage ce qui engendre des défauts de surface sur la bande.Un banc d’essai a été conçu et fabriqué dans le but d’analyser ces instabilités et d’anticiper leur apparition. A partir d’observations, la dynamique structurelle de la bande a été simplifiée à un mode de rotation rigide. Le banc comporte une plaque oscillante en mouvement forcé.Celle-ci est impactée par un dispositif de plusieurs jets axisymétriques turbulents ayant une disposition identique à celle des tours industrielles. Les efforts aérodynamiques stationnaires et instationnaires agissant sur la plaque sont mesurés au moyen de capteurs de pression.L’impact de plusieurs jets en interaction crée de très importants gradients de pression sur la plaque il est donc nécessaire que la grille de prises de pression soit très fine pour que l’estimation des efforts aérodynamiques soit correcte. La plaque est donc instrumentée de 91capteurs de pression sur une surface de 18 cm². Elle peut également être translatée dans les ois directions de l’espace, ce qui permet d’obtenir la distribution des efforts instationnaires ainsi que des coefficients aéroélastiques sur une grande surface de plaque et à différentes distances d’impact.Les mesures de pression stationnaires ont permis d’établir les courbes d’évolution des efforts d’impact des jets sur la plaque en fonction de la distance jet-plaque ainsi que de la géométrie des buses. Les résultats ont permis de déterminer la stabilité statique de la plaque en mouvement de pompage. Les mesures de vitesses des jets libres ont été effectuées paranémométrie à fil chaud et ont permis de déterminer leurs propriétés statistiques.Les mesures de coefficients aéroélastiques sur la plaque en rotation ont été effectuées surune seule géométrie de soufflage, pour différentes vitesses réduites. Les résultats mettent en évidence l’importance des effets de bords sur la stabilité de plaque. Des méthodes de post traitements ont proposées afin d’extrapoler les résultats à différentes largeurs de bande. Ils sont confrontés aux travaux de Regardin et al. (réf. [1]) et mettent en évidence des désaccords avec le cas réel. Des suggestions sont apportées afin d’améliorer la représentativité du banc vis-à-vis des bandes industrielles. / Aeroelastic instabilities of steel strips impinged by arrays of cooling gas jets have becomeone of the main issues in cooling sections of continuous annealing lines. Indeed, the new steeltreatments require very high temperature variation rates which involve increases in jetvelocities that are likely to onset some aeroelastic instabilities. Strip flutter and divergencehave already been observed and identified. These two aeroelastic instabilities imply a strongrisk of contact with the blowing boxes, which can seriously blemish the strip.An experimental test rig was designed and built in order to analyze and predict of theseinstabilities. From observations, the strip’s structural dynamics was simulated by a rigidrotation mode. The rig included a forced oscillating plate which is impinged by an array ofaxisymmetric jets having the exact industrial geometry. The plate was instrumented withpressure sensors to measure the steady and unsteady surface pressures. The impingement ofinteracting jets creates very large pressure gradients on the plate and therefore a tight mesh ofpressure taps (91 over an 18cm² jet impingement surface) was necessary to allow a goodestimation of the aerodynamic loads The plate could also be moved in the three coordinatedirections as to obtain surface mappings of the unsteady jet forces and aeroelastic coefficientscan be obtained over a wide area and different jet-to-plate distances.The variation of the impinging aerodynamic forces was established as a function of the jetto-plate distance for different nozzle geometries. These results were used to determine the jetstatic stability in plunging motion. Velocity and turbulence measurements in free jets werecarried out using hot wire anemometry in order to determine their statistical properties.Aeroelastic coefficient measurements were carried out on the oscillating plate with onlyone nozzle geometry and different reduced velocities. Results show that the plate’s stability ismainly dependent on the boundary effects. Post processing methods are suggested in order toapply the results to larger plates. Results are compared to the data of Regardin et al. (réf. [1])and emphasize some discrepancies with respect to the real case. Finally some improvementsto the test-rig are suggested for it to be more representative of the industrial situation.