No description available.

No description available.

<p>Hypersonic flow over two generic missile configurations was investigated using CFD meth-</p> <p>ods. CFD results were compared with experimental results obtained by the hypersonic flight</p> <p>lab at Texas A&M University. Baseline RANS computations involving the missile configurations at a zero deg angle-of-attack were performed, along with computations at higher angles-of-attack. As the angle-of-attack was increased, complex vortex interactions were observed in the region between the fins. Increasing the angle-of-attack generally increased heating on the windward side of the missile geometries, especially on wall surface regions</p> <p>adjacent to the fin-root vortices. The results presented highlight observed fin region vortices and regions of intense heating on the body surface. DES simulations methods were also used to explore unsteady aspects of flow around the two generic missile configurations through time-accurate CFD simulations. Power spectral plots were generated to quantify the dominant frequencies of large-scale unsteadiness.</p>

A prerequisite for aeroelastic stability prediction inturbomachines is the understanding of the fluctuatingaerodynamic forces acting on the blades. Unsteady transonicflows are complex because of mutual interactions betweentravelling pressure waves, outlet disturbances, shock motion,and fluctuating turbulent boundary layers. Complex phenomenaappear in the shock/boundary layer region and produce phaselags and high time harmonics, which can give a significantcontribution to the overall unsteady lift and torque, andtherefore affect flutter boundaries, cause large localstresses, or even severely damage the turbomachine. The present research work is concerned with theunderstanding of phenomena associated with travelling waves innon-uniform transonic flows and how they affect the unsteadypressure distribution on the surface as well as the far fieldradiated sound. In similitude with turbomachines potentialinteraction, the emphasis was put on the unsteady interactionof upstream propagating acoustic waves with an oscillatingshock in 2D and 3D nozzle flows. Both numerical andexperimental studies are carried out and compared with eachother. Results shows that the unsteady pressure distribution, bothon the bump surface and within the channel, results from thesuperposition of upstream and downstream propagating waves. Itis believed that outlet pressure perturbations propagateupstream in the nozzle, interact in the high subsonic flowregion according to the acoustic blockage theory, and arepartly reflected or absorbed by the oscillating shock,depending on the frequency of the perturbations and theintensity of the SBLI. Furthermore the shock motion amplitudeis found to be related to the mean flow gradients and localwave length of the perturbations rather than to the shockboundary layer interaction. The phase angle between incomingpressure perturbations and the shock motion increases with theperturbation frequency but also depends on the intensity of theSBLI. Additionally the phase angle "shift" observed underneaththe shock location linearly increases with the perturbationfrequency and the shock strength. Such phase shift is criticalregarding aeroelastic stability and might have a significantimpact on the phase angle of the overall aerodynamic forceacting on the blade and shift the aerodynamic damping fromstable to exciting. <b>Keywords:</b>Shock Boundary Layer Interaction, ShockMotion, Unsteady Flows, Nozzle Flows, Potential Interaction,Back Pressure Perturbations.

No description available.

<p>A prerequisite for aeroelastic stability prediction inturbomachines is the understanding of the fluctuatingaerodynamic forces acting on the blades. Unsteady transonicflows are complex because of mutual interactions betweentravelling pressure waves, outlet disturbances, shock motion,and fluctuating turbulent boundary layers. Complex phenomenaappear in the shock/boundary layer region and produce phaselags and high time harmonics, which can give a significantcontribution to the overall unsteady lift and torque, andtherefore affect flutter boundaries, cause large localstresses, or even severely damage the turbomachine.</p><p>The present research work is concerned with theunderstanding of phenomena associated with travelling waves innon-uniform transonic flows and how they affect the unsteadypressure distribution on the surface as well as the far fieldradiated sound. In similitude with turbomachines potentialinteraction, the emphasis was put on the unsteady interactionof upstream propagating acoustic waves with an oscillatingshock in 2D and 3D nozzle flows. Both numerical andexperimental studies are carried out and compared with eachother.</p><p>Results shows that the unsteady pressure distribution, bothon the bump surface and within the channel, results from thesuperposition of upstream and downstream propagating waves. Itis believed that outlet pressure perturbations propagateupstream in the nozzle, interact in the high subsonic flowregion according to the acoustic blockage theory, and arepartly reflected or absorbed by the oscillating shock,depending on the frequency of the perturbations and theintensity of the SBLI. Furthermore the shock motion amplitudeis found to be related to the mean flow gradients and localwave length of the perturbations rather than to the shockboundary layer interaction. The phase angle between incomingpressure perturbations and the shock motion increases with theperturbation frequency but also depends on the intensity of theSBLI. Additionally the phase angle "shift" observed underneaththe shock location linearly increases with the perturbationfrequency and the shock strength. Such phase shift is criticalregarding aeroelastic stability and might have a significantimpact on the phase angle of the overall aerodynamic forceacting on the blade and shift the aerodynamic damping fromstable to exciting.</p><p><b>Keywords:</b>Shock Boundary Layer Interaction, ShockMotion, Unsteady Flows, Nozzle Flows, Potential Interaction,Back Pressure Perturbations.</p>

<p>Vehicles with internal combustion (IC) engines fueled by hydrocarbon compounds have been used for more than 100 years for ground transportation. During the years and in particular in the last decade, the environmental aspects of IC engines have become a major political and research topic. Following this interest, the emissions of pollutants such as NO_x, CO₂ and unburned hydrocarbons (UHC) from IC engines have been reduced considerably. Yet, there is still a clear need and possibility to improve engine efficiency while further reducing emissions of pollutants. The maximum efficiency of IC engines used in passenger cars is no more than $40\%$ and considerably less than that under part load conditions. One way to improve engine efficiency is to utilize the energy of the exhaust gases to turbocharge the engine. While turbocharging is by no means a new concept, its design and integration into the gas exchange system has been of low priority in the power train design process. One expects that the rapidly increasing interest in efficient passenger car engines would mean that the use of turbo technology will become more widespread. The flow in the IC-engine intake manifold determines the flow in the cylinder prior and during the combustion. Similarly, the flow in the exhaust manifold determines the flow into the turbine, and thereby the efficiency of the turbocharging system. In order to reduce NO_x emissions, exhaust gas recirculation (EGR) is used. As this process transport exhaust gases into the cylinder, its efficiency is dependent on the gas exchange system in general. The losses in the gas exchange system are also an issue related to engine efficiency. These aspects have been addressed up to now rather superficially. One has been interested in global aspects (e.g. pressure drop, turbine efficiency) under steady state conditions.In this thesis, we focus on the flow in the exhaust port and close to the valve. Since the flow in the port can be transonic, we study first the numerical modeling of such a flow in a more simple geometry, namely a bump placed in a wind tunnel. Large-Eddy Simulations of internal transonic flow have been carried out. The results show that transonic flow in general is very sensitive to small disturbances in the boundary conditions. Flow in the wind tunnel case is always highly unsteady in the transonic flow regime with self excited shock oscillations and associated with that also unsteady boundary-layer separation. To investigate sensitivity to periodic disturbances the outlet pressure in the wind tunnel case  was varied periodically at rather low amplitude. These low amplitude oscillations caused hysteretic behavior in the mean shock position and appearance of shocks of widely different patterns. The study of a model exhaust port shows that at realistic pressure ratios, the flow is transonic in the exhaust port. Furthermore, two pairs of vortex structures are created downstream of the valve plate by the wake behind the valve stem and by inertial forces and the pressure gradient in the port. These structures dissipate rather quickly. The impact of these structures and the choking effect caused by the shock on realistic IC engine performance remains to be studied in the future.</p> / CICERO

<div>Initial experiments on separated shock/boundary-layer interactions were carried out within the Boeing/AFOSR Mach-6 Quiet Tunnel. Measurements were made of hypersonic laminar-turbulent transition within the separation above a compression corner. This wind tunnel features freestream fluctuations that are similar to those in</div><div>flight. The present work focuses on the role of traveling instabilities within the shear layer above the separation bubble.</div><div>A 7 degree half-angle cone with a slice and a finite-span compression ramp was designed and tested. Due to a lack of space for post-reattachment sensors, early designs of this</div><div>generic geometry did not allow for measurement of a post-reattachment boundary layer. Oil flow and heat transfer measurements showed that by lengthening the ramp, the post-reattachment boundary layer could be measured. A parametric study was completed to determine that a 20 degree ramp angle caused reattachment at 45% of the</div><div>total ramp length and provided the best flow field for boundary-layer transition measurements.</div><div>Surface pressure fluctuation measurements showed post-reattachment wave packets and turbulent spots. The presence of wave packets suggests that a shear-layer</div><div>instability might be present. Pressure fluctuation magnitudes showed a consistent transition Reynolds numbers of 900000, based on freestream conditions and distance</div><div>from the nosetip. Pressure fluctuations grew exponentially from less than 1% to roughly 10% of tangent-wedge surface pressure during transition.</div><div>A high-voltage pulsed plasma perturber was used to introduce controlled disturbances into the boundary layer. The concept was demonstrated on a straight 7 degree half-angle circular cone. The perturbations successfully excited the second-mode instability at naturally unstable frequencies. The maximum second-mode amplitudes prior to transition were measured to be about 10% of the mean surface static pressure. </div><div>The plasma perturber was then used to disturb the boundary layer just upstream of the separation bubble on the cone with the slice and ramp. A traveling instability was measured post-reattachment but the transition location did not change for any tested condition. It appears that the excited shear-layer instability was not the dominant mechanism of transition.</div>

Vehicles with internal combustion (IC) engines fueled by hydrocarbon compounds have been used for more than 100 years for ground transportation. During the years and in particular in the last decade, the environmental aspects of IC engines have become a major political and research topic. Following this interest, the emissions of pollutants such as NOx, CO2 and unburned hydrocarbons (UHC) from IC engines have been reduced considerably. Yet, there is still a clear need and possibility to improve engine efficiency while further reducing emissions of pollutants. The maximum efficiency of IC engines used in passenger cars is no more than $40\%$ and considerably less than that under part load conditions. One way to improve engine efficiency is to utilize the energy of the exhaust gases to turbocharge the engine. While turbocharging is by no means a new concept, its design and integration into the gas exchange system has been of low priority in the power train design process. One expects that the rapidly increasing interest in efficient passenger car engines would mean that the use of turbo technology will become more widespread. The flow in the IC-engine intake manifold determines the flow in the cylinder prior and during the combustion. Similarly, the flow in the exhaust manifold determines the flow into the turbine, and thereby the efficiency of the turbocharging system. In order to reduce NOx emissions, exhaust gas recirculation (EGR) is used. As this process transport exhaust gases into the cylinder, its efficiency is dependent on the gas exchange system in general. The losses in the gas exchange system are also an issue related to engine efficiency. These aspects have been addressed up to now rather superficially. One has been interested in global aspects (e.g. pressure drop, turbine efficiency) under steady state conditions.In this thesis, we focus on the flow in the exhaust port and close to the valve. Since the flow in the port can be transonic, we study first the numerical modeling of such a flow in a more simple geometry, namely a bump placed in a wind tunnel. Large-Eddy Simulations of internal transonic flow have been carried out. The results show that transonic flow in general is very sensitive to small disturbances in the boundary conditions. Flow in the wind tunnel case is always highly unsteady in the transonic flow regime with self excited shock oscillations and associated with that also unsteady boundary-layer separation. To investigate sensitivity to periodic disturbances the outlet pressure in the wind tunnel case  was varied periodically at rather low amplitude. These low amplitude oscillations caused hysteretic behavior in the mean shock position and appearance of shocks of widely different patterns. The study of a model exhaust port shows that at realistic pressure ratios, the flow is transonic in the exhaust port. Furthermore, two pairs of vortex structures are created downstream of the valve plate by the wake behind the valve stem and by inertial forces and the pressure gradient in the port. These structures dissipate rather quickly. The impact of these structures and the choking effect caused by the shock on realistic IC engine performance remains to be studied in the future. / CICERO

No description available.