ITC/USA 2007 Conference Proceedings / The Forty-Third Annual International Telemetering Conference and Technical Exhibition / October 22-25, 2007 / Riviera Hotel & Convention Center, Las Vegas, Nevada / This paper focuses on the transceiver design using BOC signal in the telemetry field, including the transmitter and receiver. The transmitter is similar as that using BPSK except from the sub-carrier modulation. But the receiver design is totally different because the BOC signal has different performance. The acquisition methods of BOC signal have been discussed such as the single-side BPSK-like, double-sides BPSK-like and hybrid processing methods, which can restrain side-peak and eliminate ambiguities. The three acquisition process principles and their performances include arithmetic complexity are described, compared and simulated using MATLAB.

International Telemetering Conference Proceedings / October 25-28, 1999 / Riviera Hotel and Convention Center, Las Vegas, Nevada / Employment of the retro-directive technique described in Reference 1 describes a totally Autonomous Ground Station providing hemispheric coverage and continuous tracking. This System establishes communications between the satellite and ground station without human intervention or moving parts. When a satellite is in view, the ground station beacon antenna, using CDMA, enables the desired satellite transmitter and directs its beam to the ground station. The ground station, using the satellite’s transmitted signal, directs it’s receive and transmit arrays to point the ground station beams to the satellite, establishing two-way communications. The process is automatic and provides continuous horizon to horizon tracking.

This thesis presents a solid state approach to the ion detection system used in the back-end of modern mass spectrometers. Although various techniques already exist to detect ions – even with the sensitivity of a single particle, the existing techniques require high voltage or lower operation temperature to counteract the noise inherent in the system. The suggested design presents an alternative to the more popular detection system whereby the requirement of high operation voltage or low operation temperature can be precluded. This is made possible through the gate capacitance of a Metal Oxide Semiconductor Field Effect Transistor (MOSFET). This thesis presents the design that utilizes the MOSFET as an ion signal amplifier; including the simulation and silicon testbench results.

BACKGROUND: Based on mainly vascular diseases and traumatic injuries, around 40,000 upper limb amputations are performed annually worldwide. The affected persons are strongly impaired in their physical abilities by such an intervention. Through myoelectric prostheses, affected persons are able to recover some of their abilities. METHODS: In order to control such prostheses, a system is to be developed by which electromyographic (EMG) measurements on the upper extremities can be carried out. The data obtained in this way should then be processed to recognize different gestures. These EMG measurements are to be performed by means of a suitable microcontroller and afterwards processed and classified by adequate software. Finally, a model or prototype of a hand is to be created, which is controlled by means of the acquired data. RESULTS: The signals from the upper extremities were picked up by four MyoWare sensors and transmitted to a computer via an Arduino Uno microcontroller. The Signals were processed in quantized time windows using Matlab. By means of a neural network, the gestures were recognized and displayed both graphically and by a prosthesis. The achieved recognition rate was up to 87% across all gestures. CONCLUSION: With an increasing number of gestures to be detected, the functionality of a neural network exceeds that of any fuzzy logic concerning classification accuracy. The recognition rates fluctuated between the individual gestures. This indicates that further fine tuning is needed to better train the classification software. However, it demonstrated that relatively cheap hardware can be used to create a control system for upper extremity prostheses.

No description available.

No description available.

International Telemetering Conference Proceedings / October 28-31, 1985 / Riviera Hotel, Las Vegas, Nevada / Digital processing techniques and related algorithms for receiving and processing space vehicle downlink signals are discussed. The combination of low minimum signal to noise density (C/No), large signal dynamic range, unknown time of arrival, and high space vehicle dynamics that is characteristic of some of these downlink signals results in a difficult acquisition problem. A method for rapid acquisition is described which employs a Fast Fourier Transform (FFT). Also discussed are digital techniques for precise measurement of space vehicle range and range rate using a digitally synthesized number controlled oscillator (NCO).

We present hereafter the development of the Liebherr Intelligent Hydraulic Cylinder, in which the hydraulic component is used as smart sensing element providing useful information for the system in which the cylinder is operated. The piston position and velocity are the most important signals derived from this new measuring approach. The performance under various load and temperature conditions (measured both on dedicated test facilities and in field in a real machine) will be presented. An integrated control electronics, which is performing the cylinder state processing, additionally allows the synchronized acquisition of external sensors. Providing comprehensive state information, such as temperature and system pressure, advanced control techniques or monitoring functions can be realized with a monolithic device. Further developments, trends and benefits for the system architecture will be briefly analyzed and discussed.

Este trabalho descreve o projeto, a construção e a avaliação de um digitalizador de sinais controlado por microprocessador, desenvolvido para ser utilizado em Tomografia por Ressonância Magnética Nuclear, TORM. O digitalizador apresenta dois canais de entrada com digitalização simultânea em 256, 512 ou 1024 palavras por canal e com taxa de amostragem máxima de 22,7 Khz. A resolução é de 12 bits com conversão analógico/digital por aproximação sucessiva. Não há controles manuais o que exige um computador hospedeiro para o ajuste de parâmetros via interface de comunicação paralela destinada para este fim. Opcionalmente pode-se utilizar uma interface serial do tipo RS232C-EIA operando com velocidade máxima de 9600 bauds. O equipamento efetua o processamento local da média acumulativa do sinal, técnica empregada para melhorar a relação sinal/ruído no caso de ruído aleatório. Um circuito dedicado à monitoração permite que se visualize em monitor X-Y tanto o sinal como a sua média. No caso da média, por ela ser acumulativa, há um ajuste automático de escala / This work describes the design, construction and evaluation of a microprocessor controlled digitizer developed to be used in Magnetic Resonance Tomography or Imaging, MRI. The digitizer presents two input channels with simultaneous digitalization in 256, 512 or 1024 words per channel with a sample rate up to 22.7 Khz. A resolution of 12 bits is obtained with successive approximation A/D conversion. There are no manual controls. So a host computer is needed to adjust the parameters through a parallel communication interface available for this purpose. Optionally, a RS232-EIA type serial interface may be used, operating at speeds up to 9600 bauds. Signal average can be processed locally by the equipment. This technique is used to improve the signal to noise ratio in case of random noise. A dedicated circuit permits the visualization of the signal and or its average on an x-y monitor. To monitor cumulative averaged data an automatic scale adjustment is provided

[pt] A presente dissertação apresenta o desenvolvimento de um transdutor de pressão de alta sensibilidade, desenvolvido para aplicações biomédicas. O transdutor é baseado em um sensor de magnetoimpedância gigante (MIG), anteriormente desenvolvido, pelo Laboratório de Biometrologia da PUC-Rio. O conhecimento a cerca das principais características do fenômeno MIG serviu de guia para as ações que foram tomadas, a fim de se estabelecer uma configuração que apresentasse maior sensibilidade ao transdutor. Mesmo que algumas dificuldades encontradas, principalmente devidas a características acústicas não levadas em consideração, apontem para a necessidade de aperfeiçoamentos, com a configuração desenvolvida no presente trabalho já é possível obter o registro do pulso arterial carotídeo. Comparações entre o transdutor ora desenvolvido e com outros transdutores de pressão existentes no mercado também destinados a aplicações biomédicas, apontam para uma sensibilidade do transdutor ora desenvolvido de magnitude igual ou mesmo superior aos convencionais. / [en] This dissertation presents a high sensitivity pressure transducer, developed for biomedical applications. The transducer is based on a Giant Magnetoimpedance (GMI) sensor previously developed at the Laboratory of Biometrology of PUC-Rio. Knowing the main characteristics of the phenomenon and of the GMI strips used, the configuration which should yield the highest possible sensitivity has been implemented. Even though some enhancements in the acoustic characteristics of the transducer are still necessary, it was already possible to record the carotid arterial pulse. Comparing the transducer herein presented with other pressure transducers also destined to biomedical applications, it already has a sensitivity of the same order of magnitude or even higher.