This thesis investigates the impact of upstream duct convolution on the plume development for high speed jets. In particular, investigations are carried out into an unconventional aero-engine exhaust systems comprised of a modified convergent-divergent rectangular nozzle where the converging section of the nozzle includes an S-bend in the duct. The motivation for this work comes from both the military and civilian sectors of the aerospace industry. The growing interest into highly efficient engines in the civilian sector and increasing complexities involved in stealth technologies for military applications has led to new design constraints on aero-engine exhaust systems that require further research into flows through more complex duct geometries. Due to a lack of experimental data into this area in the open literature validation studies are undertaken into flows through an S-bend duct and exhaust plume development from a rectangular convergent-divergent nozzle. The validation work is simulated using RANS CFD with common industrial turbulence models as well as LES with artificial inlet conditions. Subsequently, a CFD investigation into three unconventional aero-engine exhaust systems, with over-expanded conditions, with differing angles of curvature across the converging S-bend is undertaken using both RANS and LES methodologies governed by the validation work. As the curvature of the S-bend was increased it was found that the thrust and effective NPR both decrease. Whilst these changes were within acceptable levels (with some optimisation) for a circumferential extent of up to 53.1 the losses became prohibitive large at extents. For the ducts with a greater circumferential extents separation was seen to occur at the throat of the nozzle; this changes the design parameters of the nozzle leading to a higher Mach number and could potentially be harnessed to improve performance of the engine creating a `variable throat' nozzle. The impact of using different numerical solvers to simulate the flow through an unconventional aero-engine exhaust system has also been considered. The use of LES has shown that the octagonal, hexahedral and trapezoidal shapes initially observed in the development of the plumes of the RANS cases are likely to be an artifact caused by the RANS solver, as would the transverse total pressure gradients observed in the RANS cases at the nozzle exit as they are both absent from all of the LES results. Likewise the implementation of realistic inlet conditions has a significant impact on the development of the plume, particularly in the length of the potential core and the number of shock cells.

abstract: The objective of this study is to understand how to integrate conical spike external compression inlets with high bypass turbofan engines for application on future supersonic airliners. Many performance problems arise when inlets are matched with engines as inlets come with a plethora of limitations and losses that greatly affect an engine’s ability to operate. These limitations and losses include drag due to inlet spillage, bleed ducts, and bypass doors, as well as the maximum and minimum values of mass flow ratio at each Mach number that define when an engine can no longer function. A collection of tools was developed that allow one to calculate the raw propulsion data of an engine, match the propulsion data with an inlet, calculate the aerodynamic data of an aircraft, and combine the propulsion and aerodynamic data to calculate the installed performance of the entire propulsion system. Several trade studies were performed that tested how changing specific design parameters of the engine affected propulsion performance. These engine trade studies proved that high bypass turbofan engines could be developed with external compression inlets and retain effective supersonic performance. Several engines of efficient fuel consumption and differing bypass ratios were developed through the engine trade studies and used with the aerodynamic data of the Concorde to test the aircraft performance of a supersonic airliner using these engines. It was found that none of the engines that were tested came close to matching the supersonic performance that the Concorde could achieve with its own turbojet engines. It is possible to speculate from the results several different reasons why these turbofan engines were unable to function effectively with the Concorde. These speculations show that more tests and trade studies need to be performed in order to determine if high bypass turbofan engines can be developed for effective usage with supersonic airliners in any possible way. / Dissertation/Thesis / Run file and text files from the propulsion simulations performed in NPSS. / Input and output file used in EDET to generate aerodynamic data of Concorde. / Five column propulsion data of tested engines after inlet matching. / Masters Thesis Aerospace Engineering 2018