The contious reduction in size and work voltage of the new generation integrated circuits (ICs) requires the reducction of the thickness of the different layers that make up (especially the gate oxides and levels of isolation between conductors), in order to increase its density and speed of integration, reducing its energy consumption. However, these improvements involve an increase in their sensitivity to external perturbations such as fluctuations in the electricity network, capacitive coupling or electrostatic discharge (ESD). Although there is a wide range of electronic devices designed to protect ICs from such disturbances avoiding destruction (Zener diodes, thyristors, etc.), The continuous reduction of voltage operation and increasing the frequency of work has required a major research effort to adapt the protective devices to the new conditions of operation. The main features that should satisfy any device designed to protect an electronic system are: fast response, low parasitic capacity, driving in low resistance, high absorption capacity of current, low leakage current in reverse, minimum size, low cost, should not interfere in the normal mode of operation of the system that protects and must maintain unchanged its electrical characteristics over time. In high voltage applications, Zener diodes and thyristors are the most used, both in format as a discreet way to the monolithic IC, for protection against ESD phenomena. However, new generations of ICs for mobile applications (portable computers, telecommunications, remote control systems, etc.) Require devices capable of working at low voltage and low energy consumption (in order to maximize the life of batteries ). Under these conditions, the protection of traditional elements are not optimal, so that further protection devices with low voltage and low shooting leakage current in his block state. In this situation, the use of new protective structures based on a process of rupture by emptying (punch-through) improves the characteristics of those based on a break by avalanche (base of the traditional components). Thus, this study aims to analyze, optimize, design and produce new elements of protection by breaking with punch-through, known as Transient Voltage Suppressors (TVS), which improve the performance of Zener diodes in applications from low tension (less than 3 V). Thus, Chapter 1 describes the main electric perturbation and sources that originated, along with a description of its effect on the CIs. It also provides a description of the different existing devices suppressors, with special emphasis on TVS, the main topic for this work. In Chapter 2 presents a study of the vertical TVS based in the punch-through effect, which analyzes the electrical characteristics of its two configurations (TVS 3 layers, TVS 4 layers). It also presents the theoretical model of rupture developed for this type of structures as well as the verification of it through numerical simulations and experimental data. Chapter 3 deals with the design, fabrication and characterization of vertical TVS. We show the technological processes done and the improvements are detailed, demonstrating the superiority of TVS 4 layers respect to the TVS 3 layers and Zener diodes. Chapter 4 presents the first study published on lateral punch-through TVS devices intended to be integrated with the circuitry to protect. The study was conducted for different configurations proposed in technology Bulk Silicon, compared among themselves and choose the configuration that shows better characteristics. This chapter also presents a novel way of using the field plate to reduce the breakdown voltage into the lateral TVS. Finally, and as a line of the future, assessing the feasibility of integrating lateral TVS devices in SOI (Silicon-On-Insulator) substrates. Finally, Chapter 5 shows the manufacturing of lateral TVS. Details the technological process, the design of masks, clean room manufacturing in the characterization and finally, whether technological, using techniques of Reverse Engineering, as electric.

Orientador: Jose Pissolato Filho / Dissertação (mestrado) - Universidade Estadual de Campinas, Faculdade de Engenharia Eletrica e de Computação / Made available in DSpace on 2018-08-06T10:45:47Z (GMT). No. of bitstreams: 1 MarinMesa_HenryRamon_M.pdf: 775188 bytes, checksum: d44b6096c03070dff5fb491bb2b0d7dd (MD5) Previous issue date: 2005 / Resumo: Este trabalho apresenta uma análise computacional usando a técnica numérica TLM (Transmission Line Method) do comportamento das tensões transitórias em sistemas de aterramento, quando submetidas a fenômenos impulsivos do tipo descargas atmosféricas. É apresentada uma revisão bibliográfica sobre o tema e os diferentes métodos numéricos usados para modelar sistemas de aterramento. A técnica numérica TLM é apresentada, assim como, as equações para a determinação dos parâmetros usados nas simulações e o fluxograma do programa computacional desenvolvido. O programa foi escrito em Fortran e validado comparando os resultados obtidos com simulações e testes experimentais publicados por outros autores. Com o objetivo de obter o comportamento das tensões transitórias sobre diferentes situações, foi estudada a influência de alguns parâmetros no comportamento transitório das malhas de aterramento / Abstract: This work, by using the TLM (Transmission Line Method) numeric technique, presents a computational analysis of the transitory tensions behavior in grounding systems, when submitted to impulsive phenomena of the atmospheric discharge type. A bibliographical revision on the theme and the different numeric methods used for modelling grounding systems, including the TLM numeric technique, are explained, as well as the equations for the determination of the parameters used in the simulations and the flowchart of the software developed. The program written in Fortran was validated comparing simulations and experimental tests published by other authors. For the purpose of obtaining the transitory tensions behavior in different situations, we studied the influence of some parameters in the transitory behavior of grounding meshes / Mestrado / Energia Eletrica / Mestre em Engenharia Elétrica