Acoustic metamaterials have been shown to support acoustic surface waves when excited by a broadband signal in a quiescent environment and these waves could be manipulated by varying the geometry of the structure making up the metamaterial. The study presented here demonstrates the generation of trapped acoustic surface waves when excited by a turbulent flow source. The metamaterial and flow were interfaced using a Kevlar covered single cavity whose Kevlar side faced the flow to ensure no significant disturbance to the flow and the other side was open to a quiescent (stationary) environment housing the metamaterial. Acoustic measurements were performed very close to the surface of the metamaterial in the Anechoic Wall Jet Facility at Virginia Tech using two probe-tip microphones and correlation analysis yielded the structure of the surface waves. Two different metamaterials; slotted array and meander array were tested and characterized by their dispersion relations, temporal correlations, and spatial-temporal structure. The measurements proved the existence of surface waves with propagating speeds of a tenth of the speed of sound, when excited by a turbulent boundary layer flow. These waves were much weaker than the overlying flow exciting them but showcased excellent attenuation properties away from the source of excitation. Measurements along the length of the unit-cell geometry of the metamaterial demonstrated high coherence over a range of frequencies limited by the dimension of the cell. This was a surprising behavior provided the cavity was excited by a fully developed turbulent flow over a flat plate and indicated to an area averaging phenomenon.
A wall normal two-dimensional particle image velocimetry (2D-PIV) measurement was performed over the Kevlar covered cavity and a smooth surface to study the effects of the cavity on the flow. The field of view was the same for both cases which made direct flow comparison possible. Flow characteristics such as the boundary layer profiles, Reynolds stress profiles and fluctuating velocity spectrum were studied over the cavity and at downstream locations to quantify the differences in the flows. The boundary layer profiles collapsed in the inner region of the boundary layer but there were small differences in the outer region. The Reynolds stress profiles were also very similar with differences within the uncertainties of processing the images and it reflected similar average behavior of the flow over a smooth wall and a Kevlar covered cavity. The fluctuating velocity spectrum studied over the cavity location showed some differences at low frequencies for all wall normal locations while at higher frequencies the differences were within ±3 dB. These measurements showcased the underlying physics behind the interaction of acoustic metamaterials and turbulent boundary layer flows creating possibilities of using these devices for flow control although further analysis/optimization is needed to fully understand the capabilities of these systems. The demonstration of no significant effect on flow by the Kevlar covered cavity stimulated development of sensors which can average over a region of the wall pressure spectrum. / M.S. / In the field of physics, acoustic metamaterials have gained popularity due to their ability to exhibit certain properties such as sound manipulation which cannot be seen in regular materials. These materials have a key feature which is the periodic arrangement of geometric elements in any dimension. These materials can support a phenomenon termed as acoustic surface waves which are essentially pressure disturbances in the medium which behave differently than some known phenomenon such as sound waves when excited by a broadband pressure signal in a stationary medium. Also, it has been shown that these materials can change the nature of the acoustic surface waves if their geometry is changed. Here a successful attempt has been made to link two different fields in physics: acoustic metamaterials (acoustics) and turbulent flows (fluid dynamics).
The study here uses turbulent boundary layer flows to excite these metamaterials to show the existence of acoustic surface waves. This is done by creating an interface between the flow and the metamaterial using a Kevlar covered through cavity which is essentially a through hole connecting to different sides: flow side and the stationary air/quiescent side. This cavity acted as the source of excitation for the metamaterial. The Kevlar covering ensures that the flow does not get disturbed due to the cavity which was also proved in this study using a visualization technique: Particle Image Velocity (PIV). Two microphones were used to study the pressure field very close to two metamaterials; one was referred to as the slotted array comprised of slot cavities arranged in one dimension (along the direction of the flow), while the other was termed as the meander array and it comprised of a meandering channel. The pressure field was well characterized for both the acoustic metamaterials and it was proved that these metamaterials could support acoustic surface waves even when excited by a turbulent flow. The idea here was to fundamentally understand the interaction of acoustic metamaterials and turbulent flows, possibly finding use in applications such as trailing edge noise reduction. The use of these metamaterials in direct applications needs further investigation. A finding from the pressure field study showed that the pressure measured along the length of the Kevlar covered cavity was uniform. The flow visualization study looked at the turbulent flow on a smooth wall and over a Kevlar covered cavity. This was done by injecting tiny particles in air and shooting a laser sheet over these to illuminate the flow. Images were recorded using a high-speed camera to track the movement of these particles. It was found that the flow was unaffected with or without the presence of a Kevlar covered cavity. This result coupled with the pressure field uniformity could have some wide applications in the field of pressure sensing.
| Identifer | oai:union.ndltd.org:VTETD/oai:vtechworks.lib.vt.edu:10919/104742 |
| Date | 28 July 2021 |
| Creators | Damani, Shishir |
| Contributors | Aerospace and Ocean Engineering, Devenport, William J., Lowe, K. Todd, Alexander, W. Nathan |
| Publisher | Virginia Tech |
| Source Sets | Virginia Tech Theses and Dissertation |
| Language | English |
| Detected Language | English |
| Type | Thesis |
| Format | ETD, application/pdf, application/pdf |
| Rights | Creative Commons Attribution-NonCommercial 4.0 International, http://creativecommons.org/licenses/by-nc/4.0/ |
Page generated in 0.0024 seconds