The overall goal of this research work is to enhance the capabilities of large-format, polymer material extrusion, additive manufacturing (AM) systems. Specifically, the aims of this research are to (1) Construct, and develop a robust workflow for, a large-format, robotic, AM system; (2) Develop an algorithm for determining and relaying proper rotation commands for 5 degree of freedom (DoF) multi-axis deposition; and (3) Create a method for printing a removable support material in large-format AM. The development and systems-integration of a large-format, pellet-fed, polymer, material extrusion (ME), AM system that leverages an industrial robotic arm is presented. The robotic arm is used instead of the conventional gantry motion stage due to its multi-axis printing ability, ease of tool changes for multi-material deposition and/or subtraction, and relatively small machine footprint. A novel workflow is presented as a method to control the robotic arm for layer-wise fabrication of parts, and several machine modifications and workflow enhancements are presented to extend the multi-axis manufacturing capabilities of the robot. This workflow utilizes existing AM slicers to simplify the motion path planning for the robotic arm, as well as allowing the workflow to not be restricted to a single robotic deposition system.
To enable multi-axis deposition, a method for generating tool orientations and resulting deposition toolpaths from a geometry's STL file was developed for 5-DoF conformal printing and validated via simulation using several different multi-DOF robotic arm platforms. Furthermore, this research proposes a novel method of depositing a secondary sacrificial support material was created for large-format AM to enable the fabrication of complex geometries with overhanging features. This method employs a simple tool change to deposit a secondary, water-soluble polymer at the interfaces between the part and supporting structures. In addition, a means to separate support material into smaller sections to extend the range of geometries able to be manufactured via large-format AM is presented. The resultant method was used to manufacture a geometry that would traditionally be considered unprintable on conventional large-format AM systems. / Master of Science / Additive manufacturing (AM), also known as 3D printing, is a method of manufacturing objects in a layer-by-layer technique. Large-format AM is typically defined as an AM system that can create an object larger than 1 m3. There are only a few manufacturers in the world of these systems, and all currently are built on gantry-based motion stages that only allow movement of the printer in three principal axes (X, Y, Z). The primary goal of this thesis is to construct a large-format AM system that uses a robotic arm to enable printing in any direction or orientation. The use of an industrial robotic arm enables printing in multiple planes, which can be used to print structures without support structures, print onto curved surfaces, and to purt with curved layers which produces a smoother external part surface. The design of the large-format AM system was validated through successful printing of objects as large as 1.0x0.5x1.2 m, simultaneous printing of a sacrificial support material to enable overhanging features, and through completing multi-axis printing.
To enable multi-axis printing, an algorithm was developed to determine the proper toolpath location and relative orientation to the part surface. Using a part's STL file as input, the algorithm identifies the normal vector at each movement command, which is then used to calculate the required tool orientation. The tool orientations are then assembled with the movement commands to complete the multi-axis toolpath for the robot to perform.
Finally, this research presents a method of using a second printing tool to deposit a secondary, water-soluble material to act as supporting structures for overhanging and bridging part features. While typical 3D printers can generally print sacrificial material for supporting overhangs, large-format printers produce layers up to 25 mm wide, rendering any support material impossible to remove without post-process machining. This limits the range of geometries able to be printed to just those with no steep overhangs, or those where the support material is easily reachable by a tool for removal. The solution presented in this work enables the large scale AM processes to create complex geometries.
| Identifer | oai:union.ndltd.org:VTETD/oai:vtechworks.lib.vt.edu:10919/98843 |
| Date | 12 June 2020 |
| Creators | Woods, Benjamin Samuel |
| Contributors | Mechanical Engineering, Williams, Christopher B., King, Jonathan Lee, Nelson, Douglas J. |
| Publisher | Virginia Tech |
| Source Sets | Virginia Tech Theses and Dissertation |
| Detected Language | English |
| Type | Thesis |
| Format | ETD, application/pdf |
| Rights | In Copyright, http://rightsstatements.org/vocab/InC/1.0/ |
Page generated in 0.0027 seconds