Cs137 is generated from fission nuclear reactor operations. It has a half-life time of 30 years, and it is considered to be an excellent source of gamma radiation. Cs137 needs to be separated from nuclear waste before its disposal. Electrically switched ion exchange (ESIX) is one method which can be used for its separation from nuclear waste.
ESIX consists of an ion exchange film that is deposited onto a conductive electrode surface. Typically, for Cs+ removal, this film is composed of nickel hexacyanoferrate, which is known for its selectivity for that ion. The ESIX method involves the sequential application of reduction and oxidation potentials to an ion exchange film to induce the respective loading and unloading of Cs+. ESIX can be used to separate Cs137 from nuclear radioactive waste as well as Cs+ from industrial wastewater.
The goal of this research was to enhance the capacity of the nickel hexacyanoferrate ion exchange film deposited on nickel electrodes by modulating the applied potential for the ESIX film preparation. This goal was achieved by preparing an ESIX film on a nickel substrate using a two-step process in which voltage is applied to a nickel electrode surface prepared prior to the film deposition using diamond sand paper 2500 grit. The results show the preparation of a film with capacity 63 times higher than that which is previously reported in the literature.
Another four ESIX films composed of nickel hexacyanoferrate were deposited on nickel substrates with varying potentials, again in a two-step process and with surface treatment using 800 grit diamond sand paper prior to the film deposition. The surface morphology of the films was studied using scanning electronic microscope (SEM) to note any differences which could have occurred from the changes in deposition procedures. Electrospray ionization-mass spectroscopy was used to quantify the Cs+ loaded and unloaded onto the film. The results show that all of the four prepared ESIX film have a high capacity compared to those reported in the literature and that their performance regarding Cs+ loading was affected by the applied potential used for the ESIX film preparation.
Another goal of this research was to enhance the capacity of the nickel hexacyanoferrate ESIX film by changing the substrate from nickel to graphite. This goal was achieved by adsorbing the film into the pores of graphite electrodes. X-ray tomography was used to visualize the nickel hexacyanoferrate film inside the graphite electrodes. Cyclic voltammetry was conducted to detect the response of the prepared film with Cs+. Electrospray ionization-mass spectroscopy was used to quantify the amount of Cs+ adsorbed and desorbed by the electrode. The x-ray tomography results show that the graphite electrode adsorbed nickel hexacyanoferrate material. The cyclic voltammetry figures confirm that the response of each electrode prepared with Cs+ was related to the concentration of nickel hexacyanoferrate in the graphite electrode. Finally, the results obtained from electrospray ionization-mass spectroscopy about how much Cs+ was adsorbed and desorbed confirms that the two prepared electrodes have a higher capacity for Cs+ adsorption based on their interaction with a prepared Cs+ solution as a test solution.
Another goal was to observe the performance of a new ESIX film material, namely nickel hexacyanocobaltate. This film was also adsorbed by graphite electrodes. Cyclic voltammetry was conducted to measure the performance of the hexacyanocobaltate film with regard to Cs+, and the results show a significant increase in the nickel hexacyanocobaltate material inside the graphite electrode and Cs+ in the test solution. Electrospray ionization-mass spectroscopy was used to quantify the Cs+ adsorbed and desorbed by the electrode. The Results show that nickel hexacyanocobaltate as an ESIX have high capacity for Cs+ adsorption from test solution. / Thesis / Doctor of Philosophy (PhD)
| Identifer | oai:union.ndltd.org:mcmaster.ca/oai:macsphere.mcmaster.ca:11375/16588 |
| Date | 06 January 2015 |
| Creators | Tawfic, Ahmed |
| Contributors | Dickson, Sarah, Younggy, Kim, Civil Engineering |
| Source Sets | McMaster University |
| Language | English |
| Detected Language | English |
| Type | Thesis |
Page generated in 0.002 seconds