A visible light communication (VLC) system with green technology is available and enables users to use white LEDs for illumination as well as for high data rate transmission over wireless optical links. In addition, LEDs have advantages of low power consumption, high speed with power efficiency and low cost. Therefore, a great deal of research is considered for indoor VLC, as it offers huge bandwidth whilst using a significant modulation technique. This thesis is concerned with the investigation and implementation of the dicode pulse position modulation (DiPPM) scheme over a VLC link using white LED sources. Novel work is carried out for applying DiPPM over a VLC channel theoretically and experimentally including a comparison with digital PPM (DPPM) in order to examine the system performance. Moreover, a proposal of variable DiPPM (VDiPPM) is presented in this thesis for dimming control. The indoor VLC channel characteristics have been investigated for two propagation prototypes. Two models have been proposed and developed with DiPPM and DPPM being applied over the VLC channel. A computer simulation for the proposed models for both DiPPM and DPPM systems is performed in order to analyse the receiver sensitivity with the effect of intersymbol interference (ISI). Both systems are operating at 100 Mbps and 1 Gbps for a BER of 10-9. An improvement in sensitivity being achieved by the DiPPM compared to the DPPM VLC system. The system performance has been carried out by Mathcad software. The predicted DiPPM receiver sensitivity outperforms DPPM receiver at by -5.55 dBm and -8.24 dBm, at 1 Gbps data rate, and by -5.53 dBm and -8.22 dBm, at 100 Mbps, without and with guard intervals, respectively. In both cases the optical receiver sensitivity is increased when the ISI is ignored. These results based on the received optical power required by each modulation scheme. Further work has been done in mathematical evaluation carried out to calculate the optical receiver sensitivity to verify the comparison between the two systems. The original numerical results show that DiPPM VLC system provides a better sensitivity than a DPPM VLC system at a selected BER of 10-9 when referred to the same preamplifier at wavelength of 650 nm and based on the equivalent input noise current generated by the optical front end receiver. The results show that the predicted sensitivity for DPPM is greater than that of DPPM by about 1 dBm when both systems operating at 100 Mbps and 1 Gbps. Also, it is show that the receiver sensitivity is increased when the ISI is limited. Experimentally, a complete indoor VLC system has been designed and implemented using Quartus II 11.1 software for generating VHDL codes and using FPGA development board (Cyclone IV GX) as main interface real-time transmission unit in this system. The white LEDs chip based transmitter and optical receiver have been constructed and tested. The measurements are performed by using LED white light as an optical transmitter faced to photodiode optical receiver on desk. Due to the LED bandwidth limitation the achieved operating data rate, using high speed LED driver, is 5.5 Mbps at BER of 10-7. The original results for the measurements determined that the average photodiode current produced by using DiPPM and DPPM optical receivers are 8.50 μA and 10.22 μA, respectively. And this in turn indicates that the DiPPM receiver can give a better sensitivity of -17.24 dBm while compared to the DPPM receiver which gives is -16.44 dBm. The original practical results proved the simulation and theoretical results where higher performance is achieved when a DiPPM scheme is used compared to DPPM scheme over an indoor VLC system.
Identifer | oai:union.ndltd.org:bl.uk/oai:ethos.bl.uk:668185 |
Date | January 2015 |
Creators | Buhafa, Adel Mohamed |
Contributors | Sibley, Martin |
Publisher | University of Huddersfield |
Source Sets | Ethos UK |
Detected Language | English |
Type | Electronic Thesis or Dissertation |
Source | http://eprints.hud.ac.uk/id/eprint/26166/ |
Page generated in 0.0025 seconds