The initial torsional stability of a cementless total hip arthroplasty (THA) is one of the key factors in determining the biological fixation of the implant. The success of a cementless hip replacement relies on the quantity and quality of bone ingrowth that occurs. This study looked at the effects of femoral neck resection level on the initial torsional stability of cementless THA in the canine population. Twenty paired cadaver femurs were collected from dogs and implanted with canine cementless hip stems. One femur from each pair was prepared with a neck cut with its medial aspect located at the proximal aspect of the lesser trochanter (low neck cut) and the other with a neck cut with its proximo-lateral aspect at the ossum collis femoris isthmus of the greater trochanter and femoral neck (high neck cut). The specimens were then subjected to cyclic torque loads in the caudal direction (Amplitude: -0.1 N-m to set torque) at four torque levels (1 N-m, 2 N-m, 4 N-m, and 6 N-m) and the torsional displacement, axial subsidence, and strain were all recorded. A paired statistical analysis was completed so that specimens from the same dogs could be compared to each other. The low neck cut group was found to have significantly less micromotion than the high neck cut group during the 1 N-m and 4 N-m torque tests (p = 0.02 for both). Because the high neck cut specimens tended to have more micromotion they may be apt to have lower quality bone ingrowth. A significant difference was not found between the torsional displacements of the two groups. The high neck cut specimens were found to have significantly (p = 0.02) more implant rotation at 1.6 N-m of torque, however the average difference was only about 0.22 degrees which most likely does not indicate a clinically significant difference. No statistical difference was found between the axial subsidence of the high and low neck cut specimens other than at the 6 N-m level (p = 0.02). At 6 N-m the stems in the low neck cut specimens had an average upward movement of 255 +/- 310 um while the stems in the high neck cuts moved in the opposite direction and had an average downward movement of 280 +/- 695 um. The low neck specimens were found to have significantly more canal fill and implant impaction than the high neck cut specimens. This suggests that surgeons need to be mindful that they may not insert stems as deeply in femurs prepared with high neck cuts as they do in femurs with low neck cuts. This study was not able to show that one neck cut level was superior to the other, however the data indicate that the low neck cut group had slightly better stability based on having less micromotion at 1 N-m and 4 N-m and less at rotation at 1.6 N-m.
| Identifer | oai:union.ndltd.org:NCSU/oai:NCSU:etd-12122006-175747 |
| Date | 22 March 2007 |
| Creators | Brooks, Daniel John |
| Contributors | Denis J. Marcellin-Little, Ola L.A. Harrysson, C. Frank Abrams, Peter L. Mente |
| Publisher | NCSU |
| Source Sets | North Carolina State University |
| Language | English |
| Detected Language | English |
| Type | text |
| Format | application/pdf |
| Source | http://www.lib.ncsu.edu/theses/available/etd-12122006-175747/ |
| Rights | unrestricted, I hereby certify that, if appropriate, I have obtained and attached hereto a written permission statement from the owner(s) of each third party copyrighted matter to be included in my thesis, dis sertation, or project report, allowing distribution as specified below. I certify that the version I submitted is the same as that approved by my advisory committee. I hereby grant to NC State University or its agents the non-exclusive license to archive and make accessible, under the conditions specified below, my thesis, dissertation, or project report in whole or in part in all forms of media, now or hereafter known. I retain all other ownership rights to the copyright of the thesis, dissertation or project report. I also retain the right to use in future works (such as articles or books) all or part of this thesis, dissertation, or project report. |
Page generated in 0.0021 seconds