Thesis (MScEng (Civil Engineering))--Stellenbosch University, 2008. / There are currently well established compaction methods being used in laboratories globally
to prepare specimens for material testing. None of these methods provides the repeatability
and reproducibility, ease of execution or simulation and correlation to field compaction desired
by engineers. The research presented in this report was aimed at the development of a new
or adapted compaction method for bituminous stabilized materials (BSM) that would address
the aforementioned factors, by making use of a vibratory hammer. Along with this, a new
protocol was to be established.
The initial vibratory hammer that was tested was the Kango 637®. This specific vibratory
hammer suffered irreparable damage to the gearbox during the research. A replacement
Kango hammer could not be purchased, therefore a substitute hammer was purchased i.e. a
Bosch GSH 11E®, for which back-up service and replacement parts are readily available
throughout South Africa.
Significant progress had been made with the development of a laboratory compaction
protocol for BSM using the Kango Hammer. The specifications of the Bosch® hammer showed
it was superior in terms of power, weight and other technical features. Comparative testing
was therefore carried out. This allowed for the adaptation of the results achieved to that
point.
Extensive experimentation was then carried out using two types of BSM i.e. foamed bitumen
(80/100 bitumen) and bitumen emulsion (60/40 Anionic Stable Grade) stabilized material. The
initial material used for the experimentation was a G2 quality graded crushed stone.
Additional material was also obtained from a recycling project taking place along the N7 near
Cape Town. The N7 material was used to perform correlation experiments so as to determine
how representative the laboratory compacted specimens were to field compacted material.
Results showed that the vibratory hammer is capable of producing specimens for testing in
the laboratory as well as providing a possible benchmark method for accurately controlling the
quality of work on site i.e. field density control. This was done by identifying the time to and
level of refusal density compaction. The level of refusal density compaction was expressed as
a percentage of Mod AASHTO compaction and using current specifications, a potentially new
site compaction level specification was determined.
In order to asses the material applicability of the vibratory hammer compaction method, tests
regarding moisture sensitivity analysis were carried out on a G5 material. The vibratory
compaction protocol includes a specification for the type of hammer, guide-frame, surcharge
weight, compaction moisture and number of layers. Vibratory compaction can be used to
prepare two types of specimens:
• Specimens for triaxial testing with a diameter of 150mm and a height of 300mm
• Specimens for laboratory testing with a diameter of 150mm and a height of 125mm. Tests showed that the material properties prove to have an influence on the compactability
of the material. Material from the N7 recycling project had been milled out thus altering the
grading and including some RAP. This in turn influenced compaction. The vibratory hammer
moisture curve was found to shift slightly to the left when compared to the Mod AASHTO
moisture curve. The variability of the vibratory hammer was found to be well below the
specified variability of 15%. Repeatability experiments on G5 material indicate that vibratory
hammer compaction may be used on lesser quality granular materials.
A recommended procedure for the compaction of BSM was developed following the
experimentation results.
| Identifer | oai:union.ndltd.org:netd.ac.za/oai:union.ndltd.org:sun/oai:scholar.sun.ac.za:10019.1/2701 |
| Date | 12 1900 |
| Creators | Kelfkens, Rex Willem Constantyn |
| Contributors | Jenkins, K. J., Stellenbosch University. Faculty of Engineering. Dept. of Civil Engineering. |
| Publisher | Stellenbosch : Stellenbosch University |
| Source Sets | South African National ETD Portal |
| Language | English |
| Detected Language | English |
| Type | Thesis |
| Rights | Stellenbosch University |
Page generated in 0.0022 seconds