D.Phil. / Clean water (i.e. water that is free of toxic chemicals and pathogens) is essential to human health and in South Africa the demand is fast exceeding the supply. The prevalence of toxic contaminants in water remains a huge challenge for water supplying companies and municipalities. However, the presently used water treatment technologies either fail to remove these contaminants to acceptable levels or they transform them into more toxic substances (e.g., DBPs). Nanocatalysts, especially TiO2 (titania) have a proven potential to treat ‘difficult-to-remove’ contaminants and hence are expected to play an important role in solving many serious environmental and pollution challenges. In this study TiO2 nanocatalysts were used for the degradation of Rhodamine B dye both under UV and visible light irradiation. Two phases of titania, i.e. anatase and rutile phases, were compared for the degradation of Rhodamine B under UV light irradiation. The anatase titania was found to be more photocatalytically active for the degradation of Rhodamine B than the rutile phase. It completely degraded 100 mg ℓ–1 (100 mℓ) of Rhodamine B within 270 min and was two times more photocatalytically active than the rutile phase (Kapp of 0.017 min–1 compared to 0.0089 min–1). To extend the band edge of the titania nanocatalysts towards visible-light, TiO2 was doped with metal ions (Ag, Co, Ni and Pd). These metal-ion-doped titania nanocatalysts were photocatalytically active under visible-light illumination. The Pd-doped titania had the highest photodegradation efficiencies, followed by Ag-doped and Co-doped, while Ni-doped had the lowest. The optimum metal-ion loading percentage was found to be at 0.4%, with the exception of Co-doped titania as it had the highest efficiencies at 1% loadings. The free and metal-ion-doped titania nanocatalysts were embedded on carbon-covered alumina (CCA) supports. The CCA-supported TiO2 nanocatalysts were more photocatalytically active under visible light illumination than they were under UV-light irradiation. The CCA-supported metal-ion-doped titania nanocatalysts were more photocatalytically active under visible light than their unsupported counterparts. The CCA-supported Pd-TiO2 nanocatalysts were the most active while CCA-supported Ni-TiO2 catalysts were the least active. The improved photocatalytic activities observed were as a result of increased surface areas of the CCA-supported nanocatalysts. Also, supporting the nanocatalysts did not destroy the anatase phase of the titania while doping with metal ions and supporting on CCAs resulted in decreased band gap energies, hence the visible-light photocatalytic activities. Finally, the metal-ion-doped titania nanocatalysts were supported on glass slides using the layer-by-layer thin film self-assembly technique. This was to overcome the aggregation and post treatment problems associated with the use of TiO2 in suspension form. PAH and PSS were the polyelectrolytes used. These metal-ion-doped titania thin films were highly porous and strongly adhered by the polyelectrolytes onto the glass slides. The thin films were photocatalytically active for the degradation of Rhodamine B under visible light irradiation. The photocatalytic degradation efficiencies observed were similar for all four metal-ions (i.e. Ag, Co, Ni and Pd) with average degradation of 30%, 50%, 70% and 90% for 5 catalysts (5 glass slides) of 1, 3, 5 and 10 bi-layers, respectively, after 330 min. Although, these were less active than the suspended titania nanocatalysts, this study proved as a stepping stone towards large scale use of titania nanocatalysts using solar energy as the irradiation source. Also, catalyst reusability studies were performed and the PAH/PSS m-TiO2 thin films were found to be highly stable over the five cycles it was tested for.
| Identifer | oai:union.ndltd.org:netd.ac.za/oai:union.ndltd.org:uj/uj:9551 |
| Date | 16 August 2012 |
| Source Sets | South African National ETD Portal |
| Detected Language | English |
| Type | Thesis |
Page generated in 0.0019 seconds