Electrically conductive membranes (ECMs) are of significant research interest for their ability to mitigate fouling, enhance separation capacity, and induce electrochemical degradation of contaminants. Most ECM development has been in flat sheet format suitable for laboratory studies; in industrial applications, formats such as hollow fiber (HF) are preferred for their high packing density. While ECMs in HF format are emerging in research, these techniques typically employ the same methods proven for flat sheet, often involving direct deposition of conductive material onto a support membrane with no further investigation into how the deposition process affects ECM properties. This is a significant challenge for long (~1 m) HF membranes where coating uniformity is essential to ensure consistent performance. The goal of this project was to fabricate conductive HF membranes, ensuring uniform performance along the fiber. In this work, we have developed a “crossflow deposition” technique to deposit a uniform layer of single walled/ double walled carbon nanotubes (SW/DWCNTs) onto the interior surface of commercial polyether sulfone HF membranes. In a design-of-experiments model, feed pressure and crossflow velocity were shown to directly impact composite membrane conductivity and permeability. The highest permeability (~2900 LMH/bar) and conductivity (~670 S/m) were both achieved at the high pressure (0.2 bar) and high crossflow velocity (1.06 cm/s) condition. An inverse relationship was identified between conductivity and permeability for 29 different HF membranes coated under various flow and particle loading conditions. Similar trends were evident in ECM literature when comparing 80 membranes across 38 papers, covering various conductive materials, separation types, configurations, and applications. Metallic-based ECMs outperformed graphitic nanomaterial or conductive polymer-based ECMs with conductivities three orders of magnitude higher. This review also revealed a wide variation in performance testing with 35 unique pollutants in 63 total tests, indicating a need for standardization to accurately compare ECMs and a need for testing with more realistic feed sources. Finally, electrochemical degradation of methyl orange using the CNT-coated HF membranes was evaluated in batch and continuous removal experiments. Although no significant MO removal was detected in either configuration, these modules can be used for further optimization in terms of targeted conductivity, contact time, and electrochemical parameters such as applied voltage. This work highlights the existence of a conductivity/ permeability trade-off in ECM development and how manipulation of flow parameters during deposition can impact this trade-off in HF membrane development. / Thesis / Master of Applied Science (MASc) / Membrane separation technologies are a common purification strategy in many fields due to their simplicity and low energy requirements. Membranes operate by rejecting particles from feed water based on their chemical or physical properties such as size or charge. Long-term membrane operations are limited by fouling, incurring large operating costs for frequent cleaning cycles and downtime. Furthermore, traditional membrane separations only physically remove particles, presenting a risk for contaminant re-introduction into the environment. Electrically conductive membranes are an emerging strategy for addressing these concerns due to their demonstrated antifouling, enhanced selectivity, and redox capabilities. To date, these membranes have almost exclusively been developed as flat sheets with limited research into other membrane formats. Hollow fiber membranes resemble thin tubes ~1 mm in diameter and up to ~1 m in length where filtration occurs through the tubular wall of the fiber; the small diameter allows for hundreds of fibers to pack into an individual module, thus maximizing throughput. In this thesis, several issues with hollow fiber conductive membrane fabrication are addressed to ensure consistent performance along the length of the fiber. A key trade-off between membrane surface conductivity and throughput was found to exist universally in the conductive membrane field. This knowledge can be used to select fabrication methods and parameters to target certain performance ranges.
| Identifer | oai:union.ndltd.org:mcmaster.ca/oai:macsphere.mcmaster.ca:11375/26106 |
| Date | January 2020 |
| Creators | Larocque, Melissa |
| Contributors | Latulippe, David, de Lannoy, Charles, Chemical Engineering |
| Source Sets | McMaster University |
| Language | English |
| Detected Language | English |
| Type | Thesis |
Page generated in 0.0022 seconds